Installation Guide

ManualsBrandsAmerican Standard ManualsBathTown Square Right Height Elongated Toilet Bowl Only in White

IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in).

First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.

The second suggested position is next to the toilet. Between these two positions, the space for the supply

between wall and toilet is limited to 3-1/2". In this case, check your supply and hose dimensions.

2-1/4"

(57mm)

29-3/4"

(756mm)

7-1/2"

(191mm)

(25mm)

18-1/2"

(470mm)

3-1/2"

(88mm)

2-5/8"

(67mm)

8-1/2"

(217mm)

14-5/8"

(373mm)

12-3/4"

(326mm)

16-1/2"

(419mm)

15-1/4"

(390mm)

31-1/8"

(791mm)

12"

(305mm)

FINISHED

FLOOR

C/L OF SEAT POST

HOLES 5-1/2"

(140mm) CENTERS

SUPPLY

REQUIRED

(position 1 or

position 2)

(152mm)

5-1/2"

(140mm)

14"

(356mm)

(204mm)

BACK VIEW

(for reference)

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

SAVE FOR FUTURE USE

7301456-100 Rev. C

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

Town Square 1.6 gpf / 6 Lpf 2-piece Toilet

Town Square 1.28 gpf / 4.8 Lpf 2-piece Toilet

Model 2817 - Elongated, Right Height

™

with Seat

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet

flange so bolts project through mounting holes.

b. Loosely install retainer washers and nuts. Side of

washers marked "THIS SIDE UP" must face up!

NUT

TAPERED

WASHER

FLANGE

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is

installed properly, please read these instructions carefully before you begin. (Certain installations may require

professional help.) Also be sure your installation conforms to local codes.

CLOSET

FLANGE

CLOSET

BOLTS

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn

, and slide into place 6" (152 mm)

apart and parallel to wall.

ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet flange centerline must be as listed below:

IMPORTANT: Water supply on

the wall is required at 2-1/4" or

8" from centerline of the toilet

(see rough-in). First suggested

position is hidden behind the

toilet. The geometry of the toilet

gives space for this installation.

The second suggested position

is next to the toilet. Between

these two positions, the space

for the supply between wall and

toilet is limited to 3-1/2". In this

case, check your supply and

hose dimensions.

WAX RING

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent

damage), and install wax ring evenly

around waste flange (horn), with

tapered end of ring facing toilet. Apply a

thin bead of sealant around toilet base.

CLOSET

BOLT

Certiﬁed by

IAPMO R&T

SEALANT

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Town Square 1.6 gpf / 6 Lpf 2-piece Toilet Town Square 1.28 gpf / 4.8 Lpf 2-piece Toilet Model 2817 - Elongated, Right Height™ with Seat Certified by IAPMO R&T Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.
PAGE 2
6 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. ! b. 2. 3. 4. 5. 6. 7 CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! Back Side Peel both protective films off and stick bolt cover to toilet. Install bolt covers: 1. c. BOLT COVER Make sure that the bolt cover area on the toilet is clean and dry (see figure).
PAGE 3
10 11 ARM NIPPLE TOP ADJUSTMENTS REFILL TUBE a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. TANK LEVER CRITICAL LEVEL MARK ("C.L.") MUST BE 1" ABOVE OVERFLOW PIPE See Step 11 for water level adjustment method FLOAT CUP FILL VALVE b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead chain from the retainment clip and take up slack on the chain, and reinsert on lift rod.
PAGE 4
COMBO NUMBER REPAIR PARTS LIST Repair parts are determined by toilet tank number which can be found marked inside tank. 2817 2817 1.6 1.28 gpf gpf NOTE: "XXX" represents color or trim finish options. Specify when ordering. PART NO. DESCRIPTION 4216.060.XXX TOWN SQUARE TANK - 1.6 gpf (with valves and lever) 4216.128.XXX TOWN SQUARE TANK - 1.28 gpf (with valves and lever) 7381105-XXX0A TRIP LEVER ✔ ✔ 7381073-200.XXX0A BOLT CAP KIT ✔ ✔ 738565-439.