Installation Guide

ManualsBrandsAmerican Standard ManualsToilet Bowls3249.001.020

SAVE FOR FUTURE USE

7301166-100 Rev. A

Product names listed herein are trademarks of AS Americas Inc.

Putty Knife Sealant

Tape Measure

Regular Screwdriver

Adjustable Wrench

Carpenters Level

Flush Valve

RECOMMENDED TOOLS AND MATERIALS

Pictures may not exactly define contour of china

Model 3461, 3462, 3463, 3464, 3465, 3466

Model 3461, 3462, 3465, 3466 Model 3463, 3464

MADERA 16-1/2" HEIGHT FLUSH VALVE

FLOOR MOUNTED TOILETS

CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR

HANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY!

NOTE: For proper operation product requires a minimum of 30 psi working line pressure

Meets the American Disabilities Act Guidelines and ANSI A117.1

Requirements for the Physically Challenged

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this

product is installed properly, please read these instructions carefully before you begin. (Certain installations may

require professional help.) Also be sure your installation conforms to local codes.

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90°, and slide

into place 6" (152 mm) apart and parallel to wall.

CLOSET FLANGE

CLOSET BOLTS

10"

254mm

WAX RING

SEALANT

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and

install wax ring evenly around waste flange (horn), with

tapered end of ring facing toilet. Apply a thin bead of

sealant around toilet base.

730mm

(28-3/4)

1 - 1/2

SPUD

121mm

(4-3/4)

238mm

(9-3/8)

419mm

(16-1/2)

470mm

(18-1/2)

356mm

(14)

338mm

(13-5/16)

150mm

(5-7/8)

254mm

(10)

13mm

(1/2)

25mm

(1)

102mm

(4)

718mm

(28-1/4)

C/L OF SEAT POST HOLES

140mm (5-1/2) CENTERS

FINISHED WALL

FINISHED

FLOOR

C/L OF OUTLET

1" N.P.T. OR 1" C.W.T. SUPPLY

TO FLUSH VALVE

238mm

(9-3/8)

419mm

(16-1/2)

438mm

(17-1/4)

470mm

(18-1/2)

356mm

(14)

338mm

(13-5/16)

150mm

(5-7/8)

254mm

(10)

13mm

(1/2)

76mm

(3)

718mm

(28-1/4)

C/L OF SEAT POST HOLES

140mm (5-1/2) CENTERS

FINISHED WALL

FINISHED

FLOOR

C/L OF OUTLET

INSTALLATION

INSTRUCTIONS

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS MADERA 16-1/2" HEIGHT FLUSH VALVE FLOOR MOUNTED TOILETS Model 3461, 3462, 3463, 3464, 3465, 3466 Meets the American Disabilities Act Guidelines and ANSI A117.1 Requirements for the Physically Challenged NOTE: For proper operation product requires a minimum of 30 psi working line pressure RECOMMENDED TOOLS AND MATERIALS Putty Knife Sealant Tape Measure Carpenters Level Flush Valve Pictures may not exactly define contour of china 1" N.P.T. OR 1" C.W.T.
PAGE 2
5 4 BOLT CAP NUT FLANGE CLOSET FLANGE TAPERED WASHER CLOSET BOLT WASHER NUT CLOSET BOLT INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. ! CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! POSITION TOILET ON FLANGE a. Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes. b.