Installation Guide

ManualsBrandsAmerican Standard ManualsBathColony Soft 8 in. Widespread 2-Handle Low-Arc Bathroom Faucet in Polished Chrome with Speed Connect Drain

COLONY SOFT

3875.409

3875.509

SLOT

MOUNTING

SURFACE

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure

the and SEAL WASHER (3) is properly seated in SPOUT (1).

Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting

hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) ﬁrmly. Fig. A.

Hand tighten LOCKNUT (11) to secure VALVE BODY (12). Repeat above steps

for opposite VALVE BODY (12A).

Install LOCKNUT (11) onto VALVE BODY (12).

From under side of mounting surface, install VALVE BODY (12) through valve

mounting holes. Threads of VALVE BODY (12) should extent at least 5/16

of a inch above mounting surface top. Fig. B. Thread ESCUTCHEON (10)

onto VALVE BODY (12) until snug against internal stop. If necessary, adjust

LOCKNUT (11).

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Spread Lavatory Faucet with

INSTALL SPOUT

INSTALL VALVE BODY

12a

Place RUBBER RING (9) into SCUTCHEON (10).

5/16'' MIN.

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

Congratulations on purchasing your American Standard faucet with the

Speed Connect drain, a features found only on American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Fig. A.

Fig. B.

M968887 Rev.1.1

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

Summary of content (7 pages)

PAGE 1
Installation Instructions 3875.409 3875.509 COLONY SOFT Spread Lavatory Faucet with Speed Connect™ Drain C H Congratulations on purchasing your American Standard faucet with the Speed Connect drain, a features found only on American Standard faucets. Speed Connect Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A112.18.1 M 9 6 8 8 8 7 R e v. 1 .
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. 8 CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
INSTALL HANDLE TRIM 5 4 LEVER HANDLE Turn HANDLE STEM (1) to "OFF" position. H 10 4 Place the HANDLE ADAPTER (2) on the HANDLE STEM (1). Install the ADAPTER SCREW (3) and tighten securely. 3 5 Position LEVER HANDLE (4) and place on ADAPTER (2). Install the HANDLE SCREW (5) and tighten securely. 3 ACRYLIC HANDLE Turn HANDLE STEM (1) to "OFF" position. 2 2 Place the HANDLE ADAPTER (2) on the HANDLE STEM (1). 1 Position ACRYLIC HANDLE (3) and install onto ADAPTER (2).
PAGE 5
SpeedConnect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
COLONY SOFT H SPREAD LAVATORY FAUCETS M918504-0070A SCREW MODEL NUMBER M950144-0070A INDEX BUTTON, HOT M950143-0070A INDEX BUTTON, COLD M908423-0070A ACRYLIC HANDLE 3875.409 3875.