Use and Care Guide
K44
© 2006 American Standard Inc.
CADET
®
3 RIGHT HEIGHT™ ELONGATED
TOILET with the FLUSH RIGHT™ SYSTEM
VITREOUS CHINA
CADET
®
3 RIGHT HEIGHT™ ELONGATED
TOILET with the FLUSH RIGHT™ SYSTEM
❑ 2386.012
• Vitreous china
• Low-consumption (6.0 Lpf/1.6 gpf)
• EverClean™ anti-microbial ceramic glaze
• Featuring the Flush Right™ System
• 16-1/2" rim height for accessible application
• Elongated siphon action jetted bowl
• Fully-glazed 2-1/8" trapway with 2" ball pass
• Generous 9" x 8" water surface area
• Close-coupled tank with at tank cover for
superior storage
• Oversized 3" ush valve with chemical
resistant apper
• Chrome trip lever
• New Speed Connect™ tank-to-bowl
coupling system
• New sanitary dam on bowl with four point
tank stabilization
• 2 color-matched bolt caps
• 100% factory ush tested
❑ 3016.016 Right Height™ Elongated Bowl
❑ 4021.016 Tank
Nominal Dimensions:
768 x 438 x 768mm (30-1/4" x 17-1/4" x 30-1/4")
Fixture only, seat and supply by others
Alternative Tank Con gurations Available:
❑ 4021.500 Tank complete with Aquaguard Liner
❑ 4021.600 Tank complete with tank cover
locking device
❑ 4021.700 Tank complete with Aquaguard Liner
and tank cover locking device
❑ 4021.800 Tank complete with trip lever located
on right side
❑ 4021.900 Tank complete with tank cover locking
device and trip lever located on right side
Compliance Certi cations -
Meets or Exceeds the Following Speci cations:
• ASME A112.19.2M for Vitreous China Fixtures -
includes Flush Performance, Ball Pass Diameter,
Trap Seal Depth and all Dimensions
• Los Angeles Department of Water and Power
Supplementary Purchase Speci cation for
Non-Adjustability
Revised 11/05
To Be Speci ed:
❏ Color: ❏ White ❏ Bone ❏ Silver ❏ Linen ❏ Black
❏ Seat: #5325.010 Elongated Champion
®
Slow Close
solid plastic seat and cover with easy lift off feature
❏ Seat: #5284.016 Elongated EverClean™
anti-microbial solid plastic seat and cover
❏ Seat: #5311.012 Elongated Laurel molded wood
seat and cover
❏ Supply with stop:
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF
305MM (12") FROM FINISHED WALL TO C/L OF OUTLET.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
*
DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided page
FINISHED WALL
FINISHED
FLOOR
C/L OF OUTLET
SUPPLY
AS
REQ'D.
216mm
(8-1/2)
768mm
(30-1/4)
25mm ± 6mm
(1 ± 1/4)
102mm
(4)
464mm
(18-1/4)
438mm
(17-1/4)
768m
m
(30-1/4
)
419mm
(16-1/2)
*203mm
(8)
305mm
(12)
356mm
(14)
213mm
(8-3/8)
C/L OF SEAT POST HOLES
140mm (5-1/2 CENTERS)
*352mm
(13-7/8)
*152mm
(6)
238mm
(9-3/8)
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND
ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE
BUILDING FACILITIES-CHECK LOCAL CODES.