Installation Guide

ManualsBrandsAmerican Standard ManualsToilet Flush Valves Repair Parts6047111.002

Installation Instructions

(In Toronto Area only: 1-905-3061093)

Certiﬁed to comply with:

• ASSE 1037

• ANSI/ASME A112.19.2

• ADA Compliant

NOTE TO INSTALLER: Please give this manual to the customer after installation.

MANUAL FLUSH VALVE

CLOG RESISTANT

• Self-cleaning piston valve prevents clogging and reduces maintenance.

OPERATING PRESSURE:

• Overall Range: 20-125 psi **

• Recommended: 25 psi (flowing) - 80 psi (static)

FLOW REQUIREMENT:

• 25gpm (94.6 L/min).

• Flush valves include sweat solder kit.

**Water pressure over 80 psi is not recommended with most

plumbing fixtures

M965022 Rev.1.9

MODEL NUMBERS

To l e a r n more a b o u t Amer i c a n S tandard Fa u c e t s v i s i t o u r website a t : www.americanstandard.com

or U.S. customer's e-mail us at: faucetsupport@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-3061093)

FOR TOP SPUD APPLICATIONS

6047 Series

7017 Series

Exposed Flushometer

for 1-1/2" top spud Toilets

• Self-cleanin

piston va

PERATIN

PRE

• Overall Ran

e: 20-1

• Recommended: 25

LOW REQUIREME

• 25

pm (94.6 L

min)

•

ves

e s

R T

Summary of content (6 pages)

PAGE 1
I n s t a l l a t i o n I n s t ru c t i o n s MANUAL FLUSH VALVE Exposed Flushometer for 1-1/2" top spud Toilets MODEL NUMBERS 6047 Series 7017 Series FOR TOP SPUD A APPLICATIONS CLOG RESISTA RESISTANT T NT • Self-cleaning piston va valve prevents clogging and reduces maintenance. OPERATING PRESS PRESSURE: S • Overall Range: 20-1 20-125 psi ** • Recommended: 25 psi (flowing) - 80 psi (static) FLOW REQUIREMEN REQUIREMENT: N • 25gpm (94.6 L/min). L/min) • Flush valves include sw sweat w solder kit.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. 1. Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 3
Fig. 1 GENERAL DESCRIPTION: Roughing-in Dimensions MANUAL FLUSH VALVE FINISHED WALL Exposed Flushometer for 1-1/2" Top Spud Fixtures 38mm-127mm (1-1/2-5") Exclusive, self cleaning piston-operated flush valve. SUPPLY DN 25mm (1" I.P.S.) 108mm-133mm (4-1/4" to 5-1/4") -C-L- 6047.122 ROUGH-IN DIMENSION 687mm (21") *CRITICAL LEVEL 6047.122 735mm (29") 6047.121 ROUGH-IN DIMENSION 295mm (11-1/2") 152mm (6 " ) (Min.
PAGE 4
1 INSTALL SWEAT SOLDER Fig.3 ADAPTER; Fig. 3 CAUTION Fig.3a FINISHED WALL Turn water supplies off before beginning A Note: Install Optional Sweat Solder Adapter (Supplied) for copper pipe supply line. Fig. 3. (A-B)= C 1. Measure the distance (A) from the finished wall to the center of the inlet spud on the fixture. B CENTER LINE OF FIXTURE SPUD 32mm (1-1/4) FILE EDGES 2. Cut the supply pipe 1-1/4" (A-B=C) shorter then the measurement taken in Step 1.
PAGE 5
4 INSTALL FLUSH VALVE; Fig. 6a Fig. 6a & 6b 3 1. As shown in Fig. 6a, insert the side INLET FLANGE (1) on the FLUSH VALVE (2) into the SUPPLY STOP (3). Lubricate the INLET FLANGE O-RING (4) with water if necessary. Lightly tighten COUPLING NUT (5). Fig. 6a. Important: Do not use lubricants (other than water) or any type of thread sealing paste or tape. 2. Align the FLUSH VALVE (2) (Fig. 6b) directly above the DOWN TUBE (7) and VACUUM BREAKER COUPLING NUT (6).
PAGE 6
ADJUST SUPPLY STOP; Fig. 8 Fig. 8 REMOVE COVER IMPORTANT: To avoid overflowing, the SUPPLY STOP (3) must never be opened to the point where the flow from the valve exceeds the flow capacity of the fixture. The fixture and drain must be able to handle a continuous flow in case of a flush valve failure. Valve is designed to provide stated flush volume with a 25 GPM flow rate. 3 2 COUNTER-CLOCKWISE OPENS CONTROL STOP 1. Remove COVER (2) from SUPPLY STOP (3).