Installation Guide

ManualsBrandsAmerican Standard ManualsBathInnsbrook Selectronic DC Powered Touchless Lavatory Faucet in Polished Chrome

M965652 Rev. 1.9 (3/19)

Installation Instructions

SELECTRONIC

Innsbrook Lavatory Proximity Faucet

MODEL NUMBERS

605X.202

605X.204

605X.205

Certied to comply with:

• ASME A112.18.1

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@lixilamericas.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

Product No.’s & Options 1

Specications 2

Faucet Installation 2-3

Electrical Installation 4-6

Start-up / Maintenance 7-8

FAQ’s / Troubleshooting 9-10

Parts 11

CAUTION: Use only American Standard

supplied cable sets. Using non-AS supplied

cables, or cutting, splicing or modifying any

components will void the warranty.

Summary of content (11 pages)

PAGE 1
SELECTRONIC® MODEL NUMBERS Installation Instructions Innsbrook Lavatory Proximity Faucet 605X.202 605X.204 605X.205 CAUTION: Use only American Standard supplied cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No.’s & Options 1 Specifications 2 Faucet Installation 2-3 Electrical Installation 4-6 Start-up / Maintenance 7-8 FAQ’s / Troubleshooting 9-10 Parts 11 Certified to comply with: • ASME A112.18.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.
PAGE 3
Roughing-in Dimensions Fig. 1 GENERAL DESCRIPTION 175mm (6-7/8) 162mm (6-3/8) FINISHED WALL 108mm (4-1/4) 35mm (1-3/8) DIA. 3 HOLES 57mm (2-1/4) 124mm (4-7/8) MOUNTING SURFACE Note: All plumbing and electrical wiring must be installed in accordance with applicable codes, regulations and standards. 38mm (1-1/2) MAX. 125mm (4-7/8) CAUTION: Use only American Standard supplied transformers and cable sets.
PAGE 4
2 MOUNT CONTROL BOX; Fig. 2 Fig. 2 1. Determine location of CONTROL BOX (1). It must be located with-in the 14" (356mm) by 21" (533mm) s haded area shown in Figure 2 in order for electrical connections from the spout assembly to be made. NOTE: CONTROL BOX SUPPLY HOSE IS 20". DISTANCE BETWEEN WALL SUPPLY AND ENCLOSURE (1) MUST BE TAKEN INTO CONSIDERATION. 2. R emove tape from CONTROL BOX COVER (2) and pull off COVER (2).
PAGE 5
ELECTRICAL INSTALLATION Product Fig. 1 1 Page Plug-In AC Power Kit (PK00.PAC) 6 Hard-Wired AC Power Kit (PK00.HAC) 6 Multi-AC Power Kit (PK00.MAC) 7 Fig. 1a 2 Fig. 1b 3 5a 5 A DC VERSIONS ; Fig. 1 • PWRX • STANDARD BATTERY INSTALL BATTERY 1. Remove CONTROL BOX COVER (1). Fig. 1. 2. Feed the CABLES (2) through the top of CONTROL BOX (3). Fig. 1a. 4 Fig. 1c 6 OR STANDARD BATTERY VERSION ONLY F 3.
PAGE 6
VERSION; Fig. 2 B AC Fig. 2 • PLUG-IN • HARDWARE CAUTION 2 Disconnect AC power supply before opening CONTOL BOX. 3 1 Note: For AC installation, make power supply connection before mounting CONTROL BOX (3) to wall. 1. Remove CONTROL BOX COVER (1). Feed the CABLES (2) from the Faucet through the top of ENCLOSURE (3). FOR AC PLUG-IN ONLY 2a. Insert POWER CORD (8) through POWER SUPPLY GROMMET (9). Fig. 2a. 3a. Insert POWER CORD (8) through side GROMMET (6) Fig. 2a as shown. Fig. 2a. 4a.
PAGE 7
Fig. 3 Unit #2 Unit #1 Unit #3 Already installed 10 ft. EXTENSION CABLE AC POWER SUPPLY OR BLACK & WHITE POWER CONNECTIONS *MAXIMUM OF 15 UNITS PER AC POWER SUPPLY. 10' MAXIMUM CABLE LENGTH BETWEEN UNITS. C MULTI-AC VERSION (DAISY-CHAIN); Fig. 3, 3a Important: All control box covers must be removed before beginning to make daisy-chain connections. Disconnect the first unit’s Y-Adapter from power supply before making daisy-chain connections.
PAGE 8
Fig 1 MAINTENANCE A T IO N DETEC E ZON 10 4 HAND WASH SENSOR OPERATION; Fig. 1 6 3 hen the Sensor detects a user, the water immediately starts W to flow. Water flow will stop 2 seconds after user is out of sensor range. The off delay allows the user to comfortably move his hands without the flow cycling on and off. As a precaution, a safety timer will turn off the water after the sensor has been blocked for 59 seconds. The water will stay off until the blockage is removed from the detection zone.
PAGE 9
D INSTALL / REPLACE THE BATTERY Fig. 4 or PWRX; Fig. 4 CR-P2 2 1. Remove COVER from CONTROL BOX (1). 2. Disconnect BATTERY HOLDER (3) from CABLE (5). 3. Remove old BATTERY from Battery Holder (3). Install new BATTERY (2) making sure the terminal side i s inserted first and shape of the battery follows the shape o f the BATTERY HOLDER (3). 4. To replace PWRX BATTERY PACK (4), unplug and replace with new Power Pack. 5. Reconnect BATTERY HOLDER (3) to CABLE (5). 6.
PAGE 10
F GENERAL CLEANING; Fig. 5 1. For general cleaning use a damp, soft cloth to clean the spout and the sensor. Fig.6 2. For cleaning dirt use a soft cloth with diluted dish washing detergent. Wipe the area using a wet cloth and dry using a soft cloth. CAUTION Do not scratch the sensor when cleaning. Avoid using any abrasives or harsh detergents or chemicals. Avoid using anything that may scratch the spout surface. Never use polishing power, detergent or a nylon scrub brush.
PAGE 11
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? NO OPEN EXTERNAL SUPPLY STOPS. NO OPEN INTERNAL SUPPLY STOP. (HEX KEY NEEDED) YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. YES IS INTERNAL SUPPLY STOP OPEN? YES REPEATED DOUBLE FLASH ON SENSOR? NO RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR 5 SECONDS? 1 2 NO NO 1 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR.