Installation Instructions

ManualsBrandsAmerican Standard ManualsToilet Flush Valves Repair Parts6065111.002

M965646 REV. 2.1 (10/19)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093))

Ultima

™

Selectronic

Battery Powered

Toilet Flush Valve, Piston-Type

Installation Instructions

Certied to comply with ASME A112.19.2

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS supplied

cables, or cutting, splicing or modifying any components

will void the warranty.

Exposed Flushometer

for 1-1/2" Top Spud Bowls

MODEL NUMBERS

6065.111 6065.521

6065.121 6065.525

6065.161 6065.561

6065.721 6065.565

6065.761

Product to be used with WaterSense Certied

Fixture with the same rated ush volume.

Summary of content (12 pages)

PAGE 1
Installation Inst ru ct io n s Ultima™ Selectronic® Battery Powered Toilet Flush Valve, Piston-Type MODEL NUMBERS 6065.111 6065.521 6065.121 6065.525 6065.161 6065.561 6065.721 6065.565 6065.761 Exposed Flushometer for 1-1/2" Top Spud Bowls CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. Product to be used with WaterSense Certified Fixture with the same rated flush volume.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 3
Fig. 1 (Before November 2017) GENERAL DESCRIPTION: Roughing-in Dimensions SELECTRONIC® PROXIMITY TOILET FLUSH VALVE Exposed Flushometer for 1-1/2” Top Spud Fixtures Right or Left Hand Installation See (Section 5) for converting Flush Valve to Left Hand Installation. FINISHED WALL 73 mm (2-7/8") MANUAL OVERRIDE BUTTON 15˚ 127 mm (5") DETECTION ZONE 400mm-800mm (15-3/4 TO 31-1/2) SUPPLY (1" NPT.) (NPT de 1") -C-L- 292 mm (11-1/2") 419 mm (16-1/2") 108mm-134mm (4-1/4" TO 5-1/4") *-C-L152mm MIN.
PAGE 4
RECOMMENDED TOOLS; Fig. 2. Fig. 2 1. Teflon Tape 2. Flat Blade Screwdriver 3. Adjustable Wrench 4. Tape Measure 5. Hacksaw 6. Tubing Cutter 7. File 8. For Sweat Connection; Solder and Torch 9. 2.5 mm Hex Wrench 10. 1.5 mm Hex Wrench 2 1 3 4 10' 6 8 5 7 PRIOR TO INSTALLATION 9 10 • Flush all water lines prior to operation. Dirt and debris can cause flush valve to run continuously. Note: Prior to installing the Selectronic™Flush Valve the following items must be installed. 1. Toilet 2.
PAGE 5
FLUSH VALVE INSTALLATION Fig. 3 FINISHED WALL 1 INSTALL SWEAT ADAPTER; Fig. 3 CAUTION A Turn water supplies off before beginning (A-B)= C Note: Install Optional Sweat Adapter (Supplied) for copper pipe supply line. CENTER LINE OF FIXTURE SPUD B 32mm (1-1/4") FILE EDGES 1. Measure the distance (A) from the finished wall to the center of the inlet spud on the fixture. 2. Cut the supply pipe 1-1/4" (A-B=C) shorter than the measurement taken in Step 1.
PAGE 6
LUSH OUT SUPPLY LINES; Fig. 6 4 F Fig. 6 2 1. Remove STOP VALVE COVER (1) from STOP VALVE (2). REMOVE COVER 2. Open STOP VALVE (2) with a flat blade screwdriver. 1 3. Turn on water supply to flush line of any debris or sediment. 4. Close STOP VALVE (2) and replace STOP VALVE COVER (1). 2 EFT OR RIGHT HAND 5 L INSTALLATION; Fig. 7 COUNTER-CLOCKWISE OPENS STOP VALVE The unit is shipped with adjustable tailpiece on the right side.
PAGE 7
MAINTENANCE Fig. 9 1 REMOVE COVER DJUST STOP VALVE; Fig. 9 A A IMPORTANT: To avoid overflowing, the STOP VALVE (3) must never be opened to the point where the flow from the valve exceeds the flow capacity of the fixture. 3 2 COUNTER-CLOCKWISE OPENS STOP VALVE 1. After installation is complete, peel off the PROTECTIVE FILM (1) from the sensor. Standing to one side, block the sensor with your hand for 10 seconds. Remove your hand and listen for audible “click” from within the valve.
PAGE 8
C REPLACE BATTERY; Fig. 11, 11a Fig. 11 1. Loosen SET SCREW (1) with 2.5mm Hex Wrench (2) in back of FLUSH VALVE COVER (3). Fig. 11. 3 1 2. Rotate COVER (3) to the right and pull off. Fig. 11. 3. T urn COVER (3) over and disconnect the SENSOR (4) from the BATTERY HOLDER (5). Remove the BATTERY CONTAINER (6) with BATTERY HOLDER (5) and BATTERY (7) inside. Fig. 11a. 2 4. Remove BATTERY HOLDER (5) from BATTERY CONTAINER (6). Fig. 11a. 5. Remove old BATTERY from BATTERY HOLDER (5).
PAGE 9
D SET DETECTION RANGE (If Required); Fig. 13 y 14 Fig. 13 Note: The detection distance is preset and ideal for most installations. Should an adjustment be required, follow the steps below. 6 1 3 1. Loosen SET SCREW (1) with 2.5mm Hex Wrench (2) in back of FLUSH VALVE COVER (3). Fig. 13a. 2. Rotate COVER (3) to the right and pull off. Fig. 13b. VIEW “A” 2 3. T urn COVER (3) over and disconnect CABLE (4) from BATTERY HOLDER (5). Fig. 13. 4.
PAGE 10
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION IS ANGLE STOP OPEN? NO OPEN VALVE YES CRITICALLY LOW BATTERY . INSTALL NEW BATTERY YES REPEATED DOUBLE FLASH ON SENSOR? NO 1 RECONNECT BATTERY TO SENSOR. FLASH ON SENSOR FOR 5 SECONDS? NO 1 NO 2 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. DAMAGED SENSOR WIRE. REPLACE SENSOR. (ONLY IF ABSOLUTELY NEEDED) YES PUSH MANUAL OVERRIDE BUTTON; WILL THE UNIT FLUSH? DAMAGED SOLENOID.
PAGE 11
BEFORE NOVEMBER 2017 Standard Battery (6065 Series) Ultima™ Selectronic® Battery Powered AFTER NOVEMBER 2017 M964942-0021100A COVER ASSEMBLY (1.1 gpf) M970343-0021100A COVER ASSEMBLY (1.1 gpf) M964942-0021280A COVER ASSEMBLY (1.28 gpf) M970343-0021280A COVER ASSEMBLY (1.28 gpf) M964942-0021600A COVER ASSEMBLY (1.6 gpf) M970343-0021600A COVER ASSEMBLY (1.6 gpf) M964942-0024000A COVER ASSEMBLY (1.6/1.1 gpf) M970343-0024000A COVER ASSEMBLY (1.6/1.1 gpf) M964942-0023000A COVER ASSEMBLY (1.28/1.
PAGE 12
BEFORE NOVEMBER 2017 Standard Battery (6065 Series) Ultima™ Selectronic® Battery Powered AFTER NOVEMBER 2017 M964942-0021100A COVER ASSEMBLY (1.1 gpf) M970343-0021100A COVER ASSEMBLY (1.1 gpf) M964942-0021280A COVER ASSEMBLY (1.28 gpf) M970343-0021280A COVER ASSEMBLY (1.28 gpf) M964942-0021600A COVER ASSEMBLY (1.6 gpf) M970343-0021600A COVER ASSEMBLY (1.6 gpf) M964942-0024000A COVER ASSEMBLY (1.6/1.1 gpf) M970343-0024000A COVER ASSEMBLY (1.6/1.1 gpf) M964942-0023000A COVER ASSEMBLY (1.28/1.