Installation Guide

ManualsBrandsAmerican Standard ManualsBathRidgley 4 in. Centerset 2-Handle Low-Arc Bathroom Faucet in Vintage Copper

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Centerset Lavatory Faucet with the

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

INSTALL FAUCET

SINK OR

MOUNTING

SURFACE

POP-UP

CABLE

Turn off hot and cold water supplies before beginning.

Insert FAUCET (1) and CABLE CONNECTOR (2) through

mounting holes of Sink or mounting surface.

Fig. A.

Assemble LOCKNUTS (3) onto SHANKS (4) ( from under

side of Sink. Hand tighten ﬁrmly.

Fig. B.

Turn off hot and cold water

supplies before beginning.

CAUTION

(HAND TIGHTEN)

Fig. A.

Fig. B.

RIDGLEY™

M965045

7094VCF

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

Summary of content (6 pages)

PAGE 1
Installation Instructions 7094VCF RIDGLEY™ Centerset Lavatory Faucet with the Speed Connect™ Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A112.18.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. 8 CHECK OPERATION OF POP-UP 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Fig. B. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
9 TEST INSTALLED FITTING 4 With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3) by turning counter-clockwise using AERATOR KEY (3a). 1 1 Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3) turning clockwise using AERATOR KEY (3a). 3 CHECK DRAIN CONNECTIONS 3a Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK.
PAGE 5
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.