Installation Instructions

ManualsBrandsAmerican Standard ManualsBathroom Sink Faucets7186201.002

7186.201

7186.211

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Adjustable Wrench Flat Head Screwdriver Slip Jaw Pliers

Recommended tools

Tubing Cutter

INSTALL FAUCET

LAVATORY OR

MOUNTING

SURFACE

POP-UP

CABLE

Turn off hot and cold water supplies before beginning.

Insert FAUCET (1) and CABLE CONNECTOR (2) through

mounting holes of Sink or Mounting Surface.

Assemble RUBBER WASHER (3), METAL WASHER (4) and

LOCKNUTS (5) onto SHANKS (6) from under

side of Sink. Center FAUCET (1) and tighten

LOCKNUTS (5) ﬁrmly.

Turn off hot and cold water

supplies before beginning.

CAUTION

FLUENT™

Centerset Lavatory Faucet

with Speed Connect

Drain

Congratulations on purchasing your

American Standard faucet with Speed

Connect drain, a feature found only

on American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Heplful tips for removing your current drain can be found in the Troubleshooting section of

these instructions.

To ensure that your installation proceeds smoothly-please read these instructions carefully

before you begin.

M965624

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

Summary of content (7 pages)

PAGE 1
FLUENT™ Centerset Lavatory Faucet with Speed Connect® Drain Installation Instructions 7186.201 7186.211 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A112.18.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 4 REMOVE FLANGE Fig. A. 1 Thread FLANGE (1) counter-clockwise and remove Fig. B. FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto CABLE ATTACHMENT POINT (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 8 1-1/4” O.D. CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly, refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. 4 Remove AERATOR (3). Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3). 1 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
PAGE 5
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
FLUENT™ Centerset Lavatory Faucet with Speed Connect® Drain MODEL NUMBERS 7186.201 7186.