Installation Guide

ManualsBrandsAmerican Standard ManualsBathQuentin 8 in. Widespread 2-Handle Mid-Arc Bathroom Faucet in Polished Chrome

GROOVE IN

(FAUCET BASE)

MOUNTING

SURFACE

M965238 REV. 1.4 (3/15)

7440.801

7440.851

Certiﬁed to comply with ANSI A112.18.1

Adjustable Wrench Flat Blade Screwdriver Channel Locks

Recommended tools

Tubing Cutter

INSTALL SPOUT

Turn off hot and cold water

supplies before beginning.

CAUTION

Seat SEAL (1) into under side of ESCUTCHEON BASE (2).

Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN

CABLE ASSEMBLY (5) through the mounting hole of lavatory or

mounting surface.

From below, push GASKET (6) with RETAINING WASHER (7) onto

MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (8),

pushing faucet to back of sink, so SUPPLIES (3) rests against

mounting hole.

Adjust Faucet so that it is centered. Tighten MOUNTING NUT (8)

to complete faucet mounting.

INSTALLATION

INSTRUCTIONS

WIDESPREAD LAVATORY

FAUCET with

Speed Connect

Drain

7440.801

7440.851

QUENTIN™

To ensure that your installation proceeds smoothly-please read these instructions carefully

before you begin.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only

on American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

To change from swivel to ﬁxed spout, proceed as follows:

Remove PLUG BUTTON (9) from back of spout. VIEW “A”

Remove SET SCREW (10) using screwdriver.

Install FIXING SET SCREW (11) (supplied with faucet)

using Hex Wrench.

Align SPOUT (12) and tighten FIXING SET SCREW (11)

to secure SPOUT (12). Replace PLUG BUTTON (9).

CONVERT TO A FIXED SPOUT IF DESIRED.

SPOUT CAN BE FIXED OR SWIVEL.

VIEW "A"

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 7440.801 7440.851 QUENTIN™ 74 4 0 . 8 01 WIDESPREAD LAVATORY FAUCET with Speed Connect® Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. 74 4 0 . 8 5 1 Speed Connect Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A112.18.
PAGE 2
VALVE INSTALLATION Place RUBBER RING (1) into DECK ADAPTER (2). Install LOCKNUT (3) and RUBBER WASHER (4) onto VALVE BODY (5). From under side of mounting surface, install VALVE BODY (5) through valve mounting hole. Threads of VALVE BODY (5) should extent at least 5/16 of a inch above mounting surface top. Fig. A. Thread DECK ADAPTER (2) onto VALVE BODY (5) until snug against internal stop. If necessary, adjust LOCKNUT (3). Tighten LOCKNUT (3) with WRENCH (6) supplied.
PAGE 3
5 POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 6 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 4
10 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 11 1-1/4” O.D. CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 5
13 TEST INSTALLED FITTING 1 With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). 1 Operate both HANDLES (1) to flush water lines thoroughly. 3 Replace AERATOR (3). 14 5 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions.
PAGE 6
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 7
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 8
QUENTIN™ WIDESPREAD LAVATORY FAUCET with Speed Connect® Drain MODEL NUMBER 7440.801 7440.