Installation Guide

ManualsBrandsAmerican Standard Manuals8 inch Widespread Sink FaucetsHampton 8 in. Widespread 2-Handle Mid-Arc Bathroom Faucet in Satin Nickel with Speed Connect Drain

SPREAD LAVATORY

FAUCETS

Certified to comply with ANSI A112.18.1M

CAUTION

Turn off hot and cold water

supplies before beginning

Insert SPOUT SHANK (1) through center hole of SINK (2),

making sure RING WASHER (3) is properly positioned

into SPOUT BASE.

SPOUT ASSEMBLY

Assemble RUBBER WASHER (4), BRASS WASHER (5) and

LOCKNUT (6) onto threads of SPOUT SHANK (1) from

underside of SINK (2).

Insert LIFT ROD (7) through SPOUT (8) and slot of BRASS

WASHER (5).

Align SPOUT (8) and tighten LOCKNUT (6). Be sure slot in

BRASS WASHER (5) is positioned to the rear as shown.

11A

VALVE INSTALLATION

5/16'' MIN.

Insert VALVE BODY (1) through hole from underside

of SINK (2). Thread of VALVE BODY (1) should extend

at least 5/16 inch above SINK (2) top. If necessary,

adjust LOCKNUT (3). Make sure RUBBER WASHER (5)

is installed.

Place RUBBER RING (4) into ESCUTCHEON (6) and thread

ESCUTCHEON (6) onto valves until snug against internal stop.

Set VALVE BODIES (1,1A) so that their outlets are

facing toward center of sink and then tighten LOCKNUT

(3) using WRENCH (7) supplied with faucet.

Required Tools

*Supplied with Fitting

*Wrench

Adjustable Wrench

Channel Locks

Phillips Screwdriver

Flat Blade Screwdriver

Thank you for selecting American-Standard...the benchmark of fine

quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these

instructions carefully before you begin.

US60404E

Installation

Instructions

7871.702

7871.712

7871.722

7871.732

7881.702

7881.712

7881.722

7881.732

SLOT

Summary of content (4 pages)

PAGE 1
SPREAD LAVATORY FAUCETS Installation Instructions 7871.702 7871.712 7871.722 7871.732 7881.702 7881.712 7881.722 7881.732 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.
PAGE 2
3 4 TEE AND HOSE INSTALLATION Connect TEE (1) to SPOUT SHANK (2). Tighten COUPLING NUT (3). MAKE WATER SUPPLY CONNECTIONS NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE PURCHASED SEPARATELY. Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES (3) or 3/8" O.D. BULL-NOSE RISERS (4). Use adjustable wrench to tighten connections. Connect COUPLING NUTS (4) of HOSE to each valve outlet and tighten securely. Do not over tighten. Be careful not to kink copper supply when bending.
PAGE 3
7 INSTALL HANDLES (CROSS) 4 4 Turn VALVE into OFF position. 3 6 Push ADAPTER (1) into HANDLE BASE (3) in a way that the male square on the ADAPTER (1) fits in the female square of the HANDLE BASE (2). 7 3 Push HANDLE BASE (2) and ADAPTER (1) onto VALVE STEM (5). Check alignment, if not satisfactory aligned; Push out ADAPTER (1) carefully. 2 Turn ADAPTER (1) either 45˚ or 90˚ so that male square on ADAPTER (1) catches different female square in HANDLE BASE (2).
PAGE 4
SPREAD LAVATORY FAUCETS 013311-YYY0A INDEX CAP (SET) 013307-YYY0A METAL CROSS HANDLE 918428-YYY0A HANDLE SCREW MODEL NUMBERS 051376-YYY0A LIFT ROD 042692-0070A PORCELAIN CROSS HANDLE 918428-YYY0A HANDLE SCREW 7871 SERIES 7881 SERIES M961718-YYY0A LIFT ROD 908501-YYY0A CROSS HANDLE BASE 060353-YYY0A PORCELAIN LEVER HANDLE 021470-YYY0A INDEX CAP 918428-0070A HANDLE SCREW 916503-YYY0A LEVER HANDLE BASE 923002-0070A HANDLE ADAPTER 060354-YYY0A METAL LEVER HANDLE 013306-YYY0A AERATOR M961719-YYY0A S