Installation Guide

M968387 Rev. 1.1
U.S. Patent No. D403,750
Patente estadounidense D403,750
Brevet U.S.A. no. D403,750
Gracias por seleccionar los productos American Standard, sinónimo de la mejor calidad
durante más de 100 años. Por favor lea estas instrucciones detenidamente antes de
comenzar para que lleve a cabo la instalación sin contratiempos.
Nous vous remercions d’avoir choisi American Standard… synonyme de qualité supérieure
depuis plus de 100 ans. Pour vous assurer que l’installation se déroulera sans difficulté,
veuillez lire attentivement ces instructions avant de commencer.
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
Cumplimiento certificado de los requisitos
de la norma ANSI A112.18.1
Certifié conforme à ANSI A112.18.1
ROUGHING-IN DIMENSIONS DIMENSIONES DE DESBASTADO DIMENSIONS DE PRÉPARATION
Instrucciones de instalación
Mode d’installation
Installation Instructions
1
ROUGHING-IN
Turn off water at main supply.
CAUTION
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When
finished soldering, flush valve body, replace cartridges, check stops (if present) and plaster guard
to continue installation. Use thread sealant or Teflon tape on threaded connections.
NOTE
COLD
FRÍA
FROID
HOT
CALIENTE
CHAUD
PLUG
TAPÓN
BOUCHON
1
7
5
3
6
2
See Roughing-in diagram before starting.
Connections are:
1/2" copper sweat for sweat inlets
1/2" female NPT for threaded inlets
Connect RISER PIPE (1) to MANIFOLD (2)
top outlet marked "SHR".
Connect TUB FILLER PIPE (3) at bottom
outlet marked "TUB".
For proper positioning the finished wall
must be within side wall of PLASTER
GUARD (4).
If the valve is installed on a fiberglass
or other thin wall application, the
PLASTER GUARD (4) can be used as a support.
Connect hot and cold water supplies.
Cap off shower pipe (5) and tub filler pipe (6).
For support, use pipe BRACES (7) secured to wooden
braces.
With valve turned off, turn on water supplies. Check for leaks.
4
Cut a 3" dia. hole in the shower stall.
If STOPS are used, drill two additional
1" holes to allow access to the stops.
Remove PLASTER GUARD (4), rotate 90
degrees so that indicated screw holes fit
MANIFOLD (2). Push CAP on valve, place
ESCUTCHEON on and attach with screws.
To assure proper positioning in relation to wall, note roughing-in dimensions.
Tome nota de las dimensiones de desbastado para asegurar la posición correcta respecto de la pared.
Pour garantir un bon positionnement par rapport au mur, tenir compte des dimensions de préparation.
4"
1/2" NPT
1/2" (12,7 MM) NPT
NPT 12,7 mm (1/2 po.)
FINISHED WALL
PARED TERMINADA
PAROI FINIE
BOTTOM OF TUB
FONDO DE LA BAÑERA
FOND BAIGNOIRE
18" OPTIONAL
OPTATIVO, 18" (45,7 cm)
OPTION 45,7 cm (18 po.)
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN 65'' AND 78''
OPTATIVO AL PISO TERMINADO,
POR LO GENERAL ENTRE
65" Y 78" (165 A 198 cm)
DISTANCE ENTRE OPTION ET
PLANCHER FINI ENTRE
165 cm ET 198 cm (65 à 78 po.)
"SEE ILLUSTRATION"
"VEA LA FIGURA"
"VOIR ILLUSTRATION"
TOP OF TUB RIM
BORDE SUPERIOR
DE LA BAÑERA
HAUT REBORD
BAIGNOIRE
1/2" NPT
1/2" (12,7 MM) NPT
NPT 12,7 mm (1/2 po.)
1/2" COPPER
1/2" (12,7 mm)
COBRE
12,7 mm
(1/2 po.) CUIVRE
R120; R120BP; R120SS; R120SSBP
R125; R125BP; R125SS; R125SSBP
4-1/16"
(103 MM)
4-1/16"
(103 MM)
4-1/16"
(103 MM)
OUTLETS 1/2" NOM.
COPPER SWEAT
SALIDA , 1/2" (12,7 MM)
NOM. COBRE SOLDADO
ORIFICE CUIVRE LISSE
12,7 mm (1/2 po.) NOM.
OUTLETS 1/2" NOM.
COPPER SWEAT
SALIDA , 1/2" (12,7 MM)
NOM. COBRE SOLDADO
ORIFICE CUIVRE LISSE
12,7 mm (1/2 po.) NOM.
INLETS 1/2" NOM.
COPPER SWEAT
ENTRADAS, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
ENTRÉES CUIVRE LISSE
12,7 mm (1/2 po.) NOM.
SWEAT INLETS
ENTRADAS SOLDADAS
ENTRÉES LISSES
THREADED INLETS (STOPS)
ENTRADAS ROSCADAS (LIMITADORES)
ENTRÉES FILETÉES (BUTÉES)
INLETS
1/2" NPT
ENTRADAS, 1/2"
(12,7 MM) NPT
ENTRÉES NPT
12,7 mm (1/2 po.)
INLETS
1/2" NPT
ENTRADAS, 1/2"
(12,7 MM) NPT
ENTRÉES NPT
12,7 mm (1/2 po.)
5-7/8"
(149 MM)
SWEAT INLETS (STOPS)
ENTRADAS SOLDADAS (LIMITADORES)
ENTRÉES LISSES (BUTÉES)
5-7/8"
(149 MM)
INLETS 1/2" NPT
ENTRADAS, 1/2"
(12,7 mm) NPT
ENTRÉES 12,7 mm
(1/2 po.)
OUTLETS 1/2" NPT
SALIDA, 1/2"
(12,7 mm) NPT
ORIFICE 12,7 mm
(1/2 po.)
OUTLETS 1/2" NPT
SALIDA, 1/2"
(12,7 mm) NPT
ORIFICE 12,7 mm
(1/2 po.)
3-3/8"
(86 mm)
3-3/8"
(86 mm)
3-3/8"
(86 mm)
THREADED INLETS
ENTRADAS ROSCADAS
ENTRÉES FILETÉES
ROUGH VALVE KIT
JUEGO DE VÁVULA SIN ACABADO
ENSEMBLE DE ROBINET ROBUSTE
VÁLVULA DE CONTROL DE VOLUMEN Y TEMPERATURA CON EQUILIBRO
DE PRESIÓN
ROBINET MITIGEUR THERMOSTATIQUE
PRESSURE BALANCE TEMPERATURE VOLUME CONTROL VALVE
1-5/8" TO 3-1/4"
1-5/8" A 3-1/4" (41 MM A 83 MM)
41 mm (1-5/8 po.) À 83 mm (3-1/4 po.)
2
0
1
2
3
4
5
6