Reminiscence Elite Whirlpool Specification Sheet

INSTALLATION INSTRUCTIONS
752859-100 Rev. E
© American Standard Inc. 2006
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
REMINISCENCE
ELITE DROP-IN™
WHIRLPOOL
2908E SERIES
FOR AFTER-SALES SERVICE CALL 1 [phone] WEEKDAYS.
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
List of Optional Components (not included):
• Flex-Jet Pulse Jet Kit*
• Flex-Jet Soft Jet Kit*
• E-Z-Install Heater*
List of Required Components (not included):
• Drain* • Bath Filler*
* see your Home Depot Retailer
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFI
Outlet
• Cement, Plaster,
Grout
66 x 36 x 24-1/4 In. (1676 x 914 x 616mm)
95 Lbs. (43 Kg.)
659 Lbs. (299 Kg.)
68 Gal. (257 L.)
55 Gal. (208 L.)
40 x 18 In. (1016 x 457mm)
53 x 28 In. (1346 x 711mm)
15 In. (381mm)
40 Lbs./Sq. Ft. (191 Kgs/Sq. m.)
23.8
44.5
GENERAL SPECIFICATIONS FOR 2908E WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.6 HP, 9.7 AMPS, 120V.PUMP
229 x 305mm
(9 X 12)
FLOOR
CUTOUT
1-1/2 N.P.T.M. THREADS
ROUGH
FLOOR
1-1/2 O.D.TAILPIECE
70mm
(2-3/4)
117mm
(4-5/8)
LEVELING STRINGER
(NOT FOR SUPPORT)
RIM AT
DRAIN END
C/L OF OVERFLOW
616mm
(24-1/4)
73mm
(2-7/8)
464mm
(18-1/4)
79mm
(3-1/8)
149mm REF.
(5-7/8)
64mm REF.
(2-1/2)
1676mm
(66)
PUMP
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
914mm
(36)
457mm
(18)
330mm
(13)
INTEGRAL
FITTING DECK
152mm
(6)
C/L OF
DRAIN
OUTLET
OUTLINE OF
CUTOUT
ON/OFF
SWITCH
INTEGRAL
SUPPORT
FEET
IN-LINE
HEATER
REMOVABLE
BLANK