Scala Corner Corner/Bathing Pool Specification Sheet

SCALA CORNER™
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
© 2002 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED.
ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
CONCEALED PIPING NOT INCLUDED.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY
HOLES: CHECK FOR INTERFERENCE
WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES
DRILLED BY INSTALLER.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1. These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided pages.
●
■
552mm
(21-3/4)
140m
m
(5-1/2)
1080mm
(42-1/2)
1524m
m
(60) TYP.
1041mm
(41)
775m
m
(30-1/2)
PROVIDE ACCESS
FOR SERVICING
PUMP & CONTROLS
216mm
(8-1/2)
406mm
(16)
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
19mm(3/4)
CUTOUT DIMENSION
1632mm
(64-1/4)
1505m
m (59-1/4) TYP.
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
1600mm
(63-1/2)
1356m
m
(53-3/8)
OF DRAIN OUTLET
C
L
ROUGH
FLOOR
502mm
(19-3/4)
464mm
18-1/4
38mm
(1-1/2)
13mm (1/2) INTEGRAL
TILE FLANGE
1-1/2" O.D. TAILPIECE
INTEGRAL
FEET
SUPPORT
LEVELING
STRINGER
(NOT FOR
SUPPORT)
1-1/2" N.P.T.M. THREADS
60mm
(2-3/8)
124mm
4-7/8
95mm
(3-3/4)
724m
m
(28-1/2)
ON/OFF
SWITCH
R
E
C
O
M
M
E
N
D
E
D
F
IT
T
IN
G
LO
C
A
TIO
N
64 X
279m
m
(2-1/2 X
11)
●
1041mm
(41)
7
7
5
m
m
(3
0
-1
/2
)
552mm
(21-3/4)
140mm (5-1/2)
1080mm
(42-1/2)
1524mm
(60) TYP.
216mm
(8-1/2)
406mm
(16)
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
19mm(3/4)
CUTOUT DIMENSION
1632mm
(64-1/4)
1505mm (59-1/4) TYP.
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
1600mm
(63-1/2)
1
3
5
6
m
m
(5
3
-3
/8
)
OF DRAIN OUTLET
C
L
ROUGH
FLOOR
502mm
(19-3/4)
464mm
18-1/4
38mm
(1-1/2)
13mm (1/2) INTEGRAL
TILE FLANGE
1-1/2" O.D. TAILPIECE
INTEGRAL
FEET
SUPPORT
LEVELING
STRINGER
(NOT FOR
SUPPORT)
1-1/2" N.P.T.M. THREADS
60mm
(2-3/8)
124mm
4-7/8
95mm
(3-3/4)
724mm (28-1/2)
RECOMMENDED FITTING LOCATION
64 X 279mm (2-1/2 X 11)
●
60 x 60 x 19-3/4 In. (1524 x 1524 x 502mm)
114 Lbs. ( 51 Kg.)
781 Lbs. (351 Kg.)
80 Gal. (303 L)
58 Gal. (220 L)
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
14 In. (356mm)
37 Lbs./Sq.Ft. (182 Kgs./Sq.m)
41.7
68.4
GENERAL SPECIFICATIONS FOR 2664 WHIRLPOOL
1.0 HP, 9.9 AMPS,120V.
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
60 x 60 x 19-3/4 In. (1524 x 1524 x 502mm)
94 Lbs. (42 Kg.)
761 Lbs. (342 Kg.)
80 Gal. (303 L)
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
14 In. (356mm)
36 Lbs./Sq.Ft. (177 Kgs./Sq.m)
41.7
68.4
GENERAL SPECIFICATIONS FOR 2664 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)