Installation Guide

ManualsBrandsAmerican Standard ManualsBathroomReliant 3 Polished Chrome 1-Handle Bathtub and Shower Faucet

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ne quality for over 140 years.

RECOMMENDED TOOLS

M965937 Rev. 1.1 (3/20)

ROUGHING-IN DIMENSIONS

Reliant 3

Pressure Balancing Bath

and Shower Trim Kit

INSTALLATION

INSTRUCTIONS

TU385500

TU385500WD

TU385501

TU385501XH

TU385501WDXH

TU385502

TU385502WD

TU385502WDXH

Plumbers’ Putty

or Caulking

Adjustable Wrench Channel Locks

Phillips Screwdriver

• To assure proper positioning in relation to wall.

Note roughing-in dimensions.

Teon Tape Flat Blade Screwdriver

CARTRIDGE INSTALLATION

Off

OFF

18" OPTIONAL

(457 mm)

FINISHED WALL

TOP OF TUB RIM

BOTTOM OF TUB

74" FOR HEAD

CLEARANCE

4-1/4" REF.

(108 mm)

5-1/2" REF.

(140 mm)

1/2" (13 mm) NPT

1/2" COPPER

7-1/2" DIA.

(191 mm)

1-1/2" REF.

(38 mm)

6" REF.

(152 mm)

3/4"" TO 2-3/8"

(19 TO 60 mm)

OPTIONAL TO FINISHED

FLOOR USUALLY

BETWEEN 65'' AND 80''

(1651 and 2032 mm)

2-3/4" MAX. (69 mm)

1-3/4" MIN. (45 mm)

4-1/2"

(115 mm)

To ensure that your installation proceeds

smoothly-please read these instructions

carefully before you begin.

For use with shower heads rated at 4.9 L/min (1.3 gpm) or higher.

• Remove PLASTER GUARD (6)

(Keep it installed for thin wall Installation).

• Remove BONNET NUT (1) by unthreading it

Counter clockwise. Remove test CAP (2).

• Remove PROTECTIVE HOUSING (3) from

CARTRIDGE (4). Install with “UP” text on top.

• Reinstall BONNET NUT (1) onto VALVE BODY (5)

and tighten rmly with 12 Nm or 9 lbs/ft.

NOTE: Specied tightening torque

of BONNET NUT (1) is critical to

assure sealing function.

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Reliant 3® Pressure Balancing Bath and Shower Trim Kit Thank you for selecting American Standard... the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. TU385500 TU385500WD TU385501 TU385501XH TU385501WDXH TU385502 TU385502WD TU385502WDXH H OFF H C Off C For use with shower heads rated at 4.9 L/min (1.3 gpm) or higher.
PAGE 2
STANDARD WALL INSTALLATION • Figure 1. Remove plaster guard from valve. Push CAP (1) over VALVE CARTRIDGE (2) until seated against stop. • Figure 2. Push ESCUTCHEON (3) onto CAP (1) and attach to valve body with LONG SCREWS (4). 1 THIN WALL INSTALLATION • Figure 1a. Push CAP (1) over VALVE CARTRIDGE (2) until seated against stop. H 3 • Figure 2a. Push ESCUTCHEON (3) onto CAP (1) and attach to valve body with LONG SCREWS (4). Off Figure 2. U P PLASTER GUARD 4 C 1 1 U P 2 Figure 1.
PAGE 3
4 ADJUST HOT LIMIT STOP • By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet valve, adjust the setting on the HOT LIMIT SAFETY STOP (1). • Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT LIMIT STOP (1). Pull forward and rotate counterclockwise one number to limit hot water temperature.
PAGE 4
Reliant 3® Pressure Balancing Bath and Shower Trim Kit MODEL NUMBER 060351-YYY0A SHOWER ARM AND FLANGE TU385500 TU385500WD TU385501 TU385501XH TU385501WDXH TU385502 TU385502WD TU385502WDXH M953579-YYY0A SHOWER HEAD (2.