Installation Guide

ManualsBrandsAmerican Standard ManualsBathroomQuentin Brushed Nickel 1-Handle Bathtub and Shower Faucet

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 140 years.

RECOMMENDED TOOLS

M965936 (8/18)

ROUGHING-IN DIMENSIONS

Quentin

™

Pressure Balancing

Bath and Shower Trim Kit

INSTALLATION

INSTRUCTIONS

TU440507

TU440508

Plumbers’ Putty

or Caulking

Adjustable Wrench Channel Locks

Phillips Screwdriver

• To assure proper positioning in relation to wall.

Note roughing-in dimensions.

Teon Tape Flat Blade Screwdriver

CARTRIDGE INSTALLATION

BOTTOM OF TUB

4-13/16" REF.

(121 mm) REF.

1/2" COPPER

9-1/4"

(234 mm)

OPTIONAL TO FINISHED

FLOOR USUALLY

BETWEEN 65'' (1651 mm)

AND 80'' (1880 mm)

TOP OF TUB RIM

1-5/8" TO 3"

(41 mm TO 76 mm)

FINISHED WALL

4" (102 mm)

74" FOR HEAD

CLEARANCE

(188 cm)

18" OPTIONAL

(457 mm)

1/2" NPT

(12.7 mm) NPT

216 mm

(8-1/2")

REF.

125 mm

(4-7/8")

REF.

1-1/2" REF.

(38 mm) REF.

2-3/4" MAX. (69 mm)

1-3/4" MIN. (45 mm)

6-3/8"

(163 mm)

7-1/4"

(184 mm)

OFF

To ensure that your installation proceeds smoothly-please

read these instructions carefully before you begin.

For use with shower heads rated at 4.9 L/min (1.3 gpm) or higher.

• Remove PLASTER GUARD (6)

(Keep it installed for thin wall Installation).

• Remove BONNET NUT (1) by unthreading it

Counter clockwise. Remove test CAP (2).

• Remove PROTECTIVE HOUSING (3) from

CARTRIDGE (4). Install with “UP” text on top.

• Reinstall BONNET NUT (1) onto VALVE BODY (5)

and tighten rmly with 12 Nm or 9 lbs/ft.

NOTE: Specied tightening torque

of BONNET NUT (1) is critical to

assure sealing function.

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS TU440507 TU440508 Quentin™ Pressure Balancing Bath and Shower Trim Kit H OFF C Thank you for selecting American Standard... the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. For use with shower heads rated at 4.9 L/min (1.3 gpm) or higher.
PAGE 2
STANDARD WALL INSTALLATION 3 • Figure 1. Remove plaster guard from valve. Push CAP (1) over VALVE CARTRIDGE (2) until seated against stop. 1 • Figure 2. Push ESCUTCHEON (3) onto CAP (1) and attach to valve body with LONG SCREWS (4). 4 THIN WALL INSTALLATION • Figure 1a. Push CAP (1) over VALVE CARTRIDGE (2) until seated against stop. H • Figure 2a. Push ESCUTCHEON (3) onto CAP (1) and attach to valve body with LONG SCREWS (4). C FF O Figure 2.
PAGE 3
5 ADJUST HOT LIMIT STOP • By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet valve, adjust the setting on the HOT LIMIT SAFETY STOP (1). • Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT LIMIT STOP (1). Pull forward and rotate counterclockwise one number to limit hot water temperature.
PAGE 4
Quentin™ Pressure Balancing Bath and Shower Trim Kit MODEL NUMBERS 060351-YYY0A SHOWER ARM AND FLANGE TU440507 TU440508 M962255-YYY0A ESCUTCHEON AND SCREWS 078016-0020A ESCUTCHEON SCREWS M970584-YYY0A DIAL PLATE M970410-0070A CARTRIDGE M907050-YYY0A CARTRIDGE CAP H C FF PURCHASE SEPARATELY O M970486-YYY0A HANDLE KIT M954805-0070A DEEP ROUGH-IN KIT M970457-0070A HANDLE ADAPTER KIT M970221-0070A SCREW KIT 8888094.