Specifications

WIFI ENABLED MULTI-COLOR PUCK LIGHTS
PIP-RGB-WIFI INSTRUCTION
Installation
1. These puck lights offer convenient, tool-free installation using the
included 3M-brand self-adhesive tape. Prior to installing your light,
select your desired trim ring color – white, black or bronze. The trim
ring can be snapped onto the light by aligning the wiring cutouts on the
ring to the wires on the puck and using gentle pressure to snap the trim
ring into place, as shown in Figure 1.
2. Thoroughly clean all surfaces to which you will install your puck lights.
Do not apply to drywall or other delicate surfaces; the adhesive may
remove paint, drywall or mar other delicate surfaces upon removal.
3. Peel off one side of the release liner on the 3M adhesive and attach the
adhesive disk to your puck light. Repeat for each puck light and for the
wave on/off sensor (make sure the adhesive pad for the wave sensor is installed on the BACK side of the sensor, not blocking the IR/wave sensor.
4. Connect the transformer’s cable to the IR/Wave sensor. Plug the first puck into the wave sensor, the second puck into the first puck, and the third puck
in to the second puck, as shown in Figure 2. Up to a total of six pucks can be connected to one power supply. To avoid permanent damage to your puck
lights, never connect more than six pucks to a single power supply. Do not conceal the cord inside walls, ceilings, soffit, kitchen cabinets, or other
similar permanent structures. Do not run the power cord through holes in walls, ceilings, or floors.
5. Plug the transformer into a 120V power outlet.
Figure 2
Thank you for your purchase of these WiFi enabled multi-color plug in puck lights. These lights feature both adjustable
white control as well as multi-color control, all controllable with the Westek WiFiSmart app or integrated wave-sensor
for touchless control. Or, pair these lights with Google Assistant or Alexa for voice control. Featuring up to 300 lumens
of light output per light in an ultra-slim, mount-anywhere design, these lights are perfect for under cabinet task lighting
or accent lighting in cabinets, closets, and more!
GETTING STARTED
• Read these instructions in their entirety before using this product.
• Do not mount this product over a stove or sink.
WARNING
• This light may present a possible shock or fire hazard if not properly
installed. Products should be installed per these instructions, and in
accordance with all local and national electrical codes.
Includes
3 puck lights, 3 white trim rings, 3 bronze trim rings, 3 black trim rings, 1 wave sensor and power supply.
Optional Accessories
Expand up to 6 pucks total with add-on puck PIP-RGB-A (sold separately).
Figure 1
Specifications
Product SKU Description Size Color Temperature Lumens Wattage Linking
PIP-RGB-WIFI 3 Pack 4”L x 4”W x 0.7”H RGB + 2700K, 3000K, 3500K, 4000K, 5000K 300lm per puck 3.5W per puck Up to 6 pucks
PIP-RGB-A Single Add-On 4”L x 4”W x 0.7”H RGB + 2700K, 3000K, 3500K, 4000K, 5000K 300lm per puck 3.5W per puck Up to 6 pucks
Operation
Your puck lights can be controlled either by the wave-sensor or by WiFi. To operate the puck lights from the wave sensor, wave your hand past the sensor at
a distance of approximately 2 inches from the sensor. A single wave turns the power on or off. Pausing your hand in front of the sensor activates continuous
dimming. To adjust the color, press the action button on the wave sensor with your finger. The available color temperature options are 2700K, 3000K, 3500K,
4000K, 5000K, red, green, blue, purple, orange, and smooth rainbow fade.
Wave
Sensor
Action
Button
Figure 3