Specifications

PLUG-IN PUCK LIGHTS WITH RF REMOTE
USLM-PIP-RF INSTRUCTION Include Transmitter USLM-PIP-RMT
Installation
1. These puck lights offer convenient, tool-free installation using 3M-branded
self-adhesive tape. Prior to installing your light, select your desired trim ring color
– white, black or bronze. The trim ring can be snapped onto the light by aligning the
wiring cutouts on the ring to the wires on the puck and using gentle pressure to
snap the trim ring into place.
2. Thoroughly clean all surfaces to which you will install your puck lights. Do not apply
to drywall or other delicate surfaces; the adhesive may remove paint, drywall or mar
other delicate surfaces upon removal.
3. Peel off one side of the release liner on the 3M adhesive and attach the adhesive
disk to your puck light. Repeat for each puck light and for the wave on/off sensor (make sure the adhesive pad for the wave sensor is installed on the BACK side of the sensor,
not blocking the IR/wave sensor.
4. Connect the transformer’s cable to the IR/Wave sensor. Plug the first puck into the wave sensor, the second puck into the first puck, and the third puck in to the second. Up to a
total of six pucks can be connected to one power supply. To avoid permanent damage to your puck lights, never connect more than six pucks to a single power supply.
Do not conceal the cord inside walls, ceilings, soffit, kitchen cabinets, or other similar permanent structures. Do not run the power cord through holes in walls, ceilings,
or floors.
5. Plug the transformer into a 120V power outlet and remove the battery pull-tab from the remote control. Your lights are now ready for use.
Operation
Your puck lights can be controlled by the remote control or the wave-sensor. To operate the puck lights from the wave sensor, wave your hand
past the sensor at a distance of 2-3 inches from the sensor. A single wave turns the power on or off. Pausing your hand in front of the sensor
activates continuous dimming. To adjust the color temperature, press the action button on the wave sensor with your finger. The available
color temperature options are 2700K, 3000K, 3500K, 4000K,
and 5000K.
To operate from the remote control, simply press the desired button on the remote to activate your lights, as shown below. The remote uses
radio frequency technology and can work through walls, around corners, and without direct line of sight. The remote is good to a maximum of
about 50’ from the lights, but walls and other objects may shorten this working range.
Thank you for your purchase of this Ultra-Slim 3-puck light set, featuring 300 lumens of bright white light per puck with 5-color
adjustable white control. These puck lights operate by RF remote control, meaning direct line of sight is not needed – you can operate
them through walls and around corners. Alternately, these lights are equipped with a hand-wave sensor, and can be controlled by a
simple wave of your hand, ideal for use during tasks like kitchen prep.
GETTING STARTED
• Read these instructions in their entirety before using this product.
• Do not mount this product over a stove or sink.
WARNING
• This light may present a possible shock or fire hazard if not properly installed.
Products should be installed per these instructions, and in accordance with
all local and national electrical codes.
Includes
3 puck lights, 3 white trim rings, 3 bronze trim rings, 3 black trim rings, 1 wave sensor, power supply and remote control.
Optional Accessories
Expand up to 6 pucks total with add-on puck PIP-RGB-A (sold separately).
Wave
Sensor
Action
Button
ON – Turns on the lights
DIM Down – Dims the lights
DIM 50% – Sets light to 50% brightness
Timers – Programs the light to turn off
automatically in 15, 30, 60, or 120 minutes
Warm CCT – Sets the light to 2700K white temperature
Cool CCT – Sets the light to 5000K white temperature
Next CCT – Cycles between 2700K, 3000K, 3500K, 4000K,
and 5000K white temperatures
OFF – Turns off the lights
DIM Up – Brightens the lights
DIM 100% – Sets light to maximum brightness
Specifications
Product SKU Description Size Color Temperature Lumens Wattage Linking
USLM-PIP-RF 3 Pack 4”L x 4”W x 0.7”H 2700K, 3000K, 3500K, 4000K, 5000K 300lm per puck 3.5W per puck Up to 6 pucks
PIP-RGB-A Single Add-On 4”L x 4”W x 0.7”H 2700K, 3000K, 3500K, 4000K, 5000K 300lm per puck 3.5W per puck Up to 6 pucks
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Warning: Do not disassemble or modify this light. Modification voids the manufacturer’s warranty and any applicable regulatory certifications this light may possess.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited express warranty that is set forth in the Limited Warranty
stated in full at www.amertac.com/warranties. The Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions explained fully in
the Limited Warranty on the website.
©2021 AmerTac
™
250 Boulder Drive
Breinigsville, PA 18031
amertac.com
Made in China
UC_TL_015_0621
(FCC ID:XDE-USLM-PIP-RMT)