Analogwecker mit schnurlosem Vibrationskissen Analogue alarm clock with cordless vibration pad Réveil analogique avec coussin vibrant inclus Analoge wekker inclusief trilkussen Bedienungsanleitung Operating Instructions Mode d’emploi Gebruiksaanwijzing TCL 190
Safety Information 1 Safety Information Please read this operating instruction manual thoroughly. Rechargeable batteries Intended use Attention: Never throw batteries into a fire. Only use This alarm clock is designed to provide an acoustic alarm or alert batteries of the same type. signal at a set time or on receipt of a telephone call. Any other Disposal use is considered unintended use.
Operating Elements 2 Operating Elements Alarm clock (front view) 1 Snooze button 2 LED: Alarm ON/OFF / Battery charge low 3 Rotary knob: Switch alarm ON/OFF 1 Status indicators in clock face LED (Pos. 2) Alarm function is activated: LED is red Battery charge low, alarm is activated: LED flashes green Battery charge low, alarm is deactivated: LED flashes orange 18 0844 800 6503 (Using an UK landline, at the time of going to print: calls cost 6p for connection charge and then 5p a minute.
Operating Elements Alarm clock (rear view) 4 Rotary knob: Volume control 5 Rotary knob: Set one of the 5 acoustic signals 6 Rotary knob: Pitch 7 Sliding switch: Vibration only", Acoustic signal only", Acoustic signal + Vibration" 8 Sliding switch: Flashing lamp ON/OFF 9 Sliding switch: Snooze delay, 0 min.", 5 min.", 15 min.
Operating Elements Status indicators on vibration pad Vibration pad LED (Pos. 1) Switched on: LED flashes green every 2 sec. Charging process: LED is red Battery charge low: LED flashes red 1 2 3 4 5 1 2 3 4 5 20 LED: ON/OFF / Battery charge low Sliding switch: Vibration pad ON /OFF Battery compartment Screws for battery compartment Connection cable socket 0844 800 6503 (Using an UK landline, at the time of going to print: calls cost 6p for connection charge and then 5p a minute.
Preparing the Equipment 3 Preparing the Equipment Safety information Attention: It is essential to read the Safety Information in Chapter 1 before starting up. Checking the package contents 2 The package contains: Content Connecting the alarm clock Please proceed as follows in order to be able to use the alarm clock: 1. First of all, insert the batteries supplied in the clock’s battery compartment.
Preparing the Equipment 4. Connect the equipment as illustrated in the diagram. Only use the telephone connection line supplied because the equipment may not function if another telephone connection line is used. Vibration pad Basic settings In order to be able to use the TCL 190 alarm clock, you must first carry out the following settings. 1. Set the time. Turn the rotary knob (15) until the clock shows the correct time. 2. Set the time at which the alarm should go off.
Preparing the Equipment Operating the vibration pad In order to use the vibration pad, it must initially be fully charged: 1. Connect the alarm clock to the mains power supply via the power adapter plug. 2. Remove the small rubber cap from the sliding switch on the vibration pad. 3. Plug one end of the connection cable in the socket in the vibration pad and in the other end in the socket for the vibration pad in the alarm clock. 4. The LED on the vibration pad lights up red. 5.
Settings and Functions 4 Settings and Functions Setting the time Selecting the acoustic signal Turn the rotary knob (5) to set the required acoustic signal. Use the rotary knob (15) to set the correct time. Setting the alarm time Use the rotary knob (14) to set the time at which the alarm should be triggered. Switching the alarm signal on and off Activate or deactivate the alarm by turning the rotary knob (3) on or off, respectively. Anticlockwise Off" or clockwise On".
Settings and Functions Setting the snooze delay 0m 5m 15m Use the sliding switch (9) to set the interval for the SNOOZE snooze delay. There are three settings available, from left to right 0 min", 5 min" or 15 min.". Activating the snooze delay If the snooze button is pressed at anytime when the light is switched off, then the illumination will switch on for 30 seconds to allow the user to see the time. After 30 seconds the illumination will go out.
In Case of Problems 5 In Case of Problems Service−Hotline Should problems arise with the device, please refer to the following information first. In the event of technical problems, please contact out service hotline under tel. 0844 800 6503 (Using an UK landline, at the time of going to print: calls cost 6p for connection charge and then 5p a minute. Mobile costs may vary). In the case of claims under the terms of guarantee, contact your sales outlet. There is a 2 year period of guarantee.
Maintenance / Guarantee 6 Maintenance / Guarantee Maintenance No claims under the terms of guarantee can be asserted after a period of two years from the date of purchase and hand−over of Clean the housing surfaces with a soft, fluff−free cloth. the product. Never use cleaning agents or solvents. Guarantee AMPLICOMMS equipment is produced and tested according to the Declaration of Conformity This device fulfils the requirements stipulated in the EU latest production methods.
Technical Data 7 Technical Data 28 Vibration pad Value Analogue alarm clock Value Range: Approx. 100 m (clear space) Frequency: 433 MHz Battery: Power supply: Input: 210-240 VAC, 50/60 Hz Output: 12 VDC, 670 mA 3 x AAA 3.6 V, 800 mAh, NiMH Initial charging time: Up to 16 h Permissible ambient temperature 0 °C to 40°C Permissible storage temperature: −20 °C to 60 °C Dimensions W / H: 113.3 x 36.6 mm Weight: 180 − 200 g Telephone plug: BS 6312 Batteries: 2 x AAA 1.
Notes Notes 29
Important Notes on the Guarantee The period of guarantee for the AMPLICOMMS product begins on the date of purchase. Rights to claims under the terms of guarantee relate to deficiencies resulting from material or production faults. Rights to claims under the terms of guarantee are annulled following intervention by the purchaser or third parties.
