Installation Guide

5
You can match your Andersen storm door lock to Schlage® or Kwikset®
entry door locks. See handle set instructions contained within handle set
box for details.
“Kwikset” is a registered trademark of Newfry LLC. “Schlage” is a registered
trademark of Schlage Lock Company.
1. Look into handle holes on door to make
sure lock case is oriented properly. Notch in
square spindle hole should be facing away
from glass panel.
TIP: If notch is not facing away from glass panel,
use handle and spindle to rotate spindle hole
into correct orientation.
1. If applicable, start at the mitered corners
and remove the clear protective tape from
both the interior and exterior of door frame.
1. Install lock case trim plate onto lock case and
fasten with one 5/8” screw. Do not overtighten.
2. Insert dead bolt key cylinder into lock case and
fasten with one 1 1/2” athead screw. Do not
overtighten.
NOTE: This door features an integrated latch
receiver in the latch rail, eliminating the need for a
traditional, separate strike plate.
1. Insert handle into outside trim plate (with
Andersen logo) with lever pointing down
and rotate handle to secure it.
2. Repeat for other handle and inside trim
plate (with slider).
3. NOTE: Trim plates should not be installed
on the door while completing above steps.
1. With handle levers held horizontal, install
both handle assemblies onto door. Spindle
will pass through square hole in lock case
and into other handle. Attach trim plates
together using two 1 1/2” pan head screws.
INSTALL
HANDLE SET
(Left Hand)
4
e
a
d
b
L
5/8”
1-1/2”
x 2
1-1/2”
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
c
1
2
1
2
i
VIEW
X
VIEW
i
VIEW
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
GLASS
DE VIDRIO
LE VERRE
NONFUNCTIONAL FEATURE
SPANISH
FRENCH