Instructions & Assembly

ASSEMBLING & INSTALLATION INSTRUCTIONS
For Chain Hang OR Ceiling Mount
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING THE FIXTURE (Fig.2).
1. Return the arms to suitable position, see figure.2.
2. Attach the cloumn(A) to the fixture body (B) by turning it clockwise
until tight.
3. Attach the glass shade (E) and collar ring(D) to the lamp holder , then
lock it securely with check ring (C).
4. Install the light bulbs in accordance with the fixture specifications
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
HANGING THE FIXTURE (Fig.1)
1. Shu
t
off the
p
owe
r
a
t
the circui
t
b
reake
r
an
d
remove old fixture
from ceiling, including the old single bar.
2. Carefully unpack new fixture and lay all the parts on a clear
surface.
3. Threa
d
the two studs into the
p
re-drilled holes in the Mounting
plate spaced the same distance apart as the holes in the
canopy .Attach the Mounting plate to the Junction Box with the
two Junction Box Screws as shown. The side of the Mounting
plate marked "GND" must face to out.
4. Using
rope
chain
p
liers to open one en
d
lin
k
of the chain
provided and connect to the fixture loop. Close the link.
5. By measuring, determine correc
t
numbe
r
of links neede
d
fo
r
proper hanging height. Using proper chain pliers disconnect and
discard remaining chain.
6. Lace the fixture wires through the chain.
7. Open the othe
r
en
d
lin
k
of the chain and hang the fixture on the
loop at the ceiling. Close the link.
8. Feed the fixture wires through the loop of the canopy and pull until
taut.
9. Slide canopy up flush to ceiling, loc
k
i
t
securely with
b
all nu
t
.
**If you not need assembly the fixture loop , please pause
and refer to Fig 4.**
1. Take ou
t
the
b
otto
m
loop of the canopy, take ou
t
the loop an
d
cover of the fixture body, then take the canopy to the fixture body,
lock it with the shim and hex nut until tight.
2. Attach the fixture
b
ody to the ceiling, loc
k
i
t
securely with the
b
all
nut.
CONNECTING THE WIRES (Fig.3)
1. Take the black wire from the ceiling junction box and the smooth
wire leg from the fixture and twist bare ends together. Twist wire
connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire
leg of fixture wire. NOTE: Twist wires together in the same
direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper w ire from the fixture together
as step 1.If junction box has no ground wire, attach the bare copper
fixture wire to the green ground screw on the single bar.
4. Tuck these wire connections neatly into the ceiling outlet box and
then raise the canopy all the way to the ceiling.
Lock it securely
with ball nut.
Your installation is now complete. Return power to the junction
box and test the fixture.
Fig.1
Fig.2
Fig.4
C
D
E
A
Pipe
Screw
B
Canopy
Ball Nut
Fig.3
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Listed
U
L
R

Summary of content (1 pages)