LED TV User Manual LE22H067 LE24H067 TÉLÉVISION À HAUTE DÉFINITION INTERFACE MULTIMÉDIA HAUTE DÉFINITION 1 www.aoc.com 2010 AOC. All Rights Reserved.
This manual provides as an operational guide to user. All statements, technical information, and recommendations in this manual and in any guides or related documents are believed reliable, but the accuracy and completeness thereof are not guaranteed or warranted, and they are not intended to be, nor should they be understood to be, representations or warranties concerning the products described.
Table of Contents IMPORTANT INFORMATION ..............................................................................................................................................3 WARNING ..............................................................................................................................................................................................................................................3 CAUTION ........................................................................
Energy Star Important Information WARNING CAUTION Please keep the factory default settings as shipped, in which the product can meet Energy Star requirements. RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION Important Safety Information RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR PRECAUCION 1) 2) 3) 4) 5) 6) 7) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth.
Wall-Mount Usage Instructions Wall-Mount installation requires the use of a Wall-Mount Bracket. When installing or removing the TV, using a Wall-Mount Bracket, be sure to use qualified contractors. If not properly secured during installation or removal from the Wall-Mount Bracket, the TV may fall and cause serious injury. Installation Placement It is recommended to watch the TV at a distance of 3 -7 times which of the screen height, and in moderate brightness.
LCD/LED Screen Electric Shock Although the LCD/LED screen is made with high-precision Do not touch the AC power cord or the TV with a wet hand. If you plug/unplug the AC power cord from the TV with a wet hand, it may cause electric shock. technology and has effective pixels of 99.99% or more, black dots or bright points of light (red, blue, or green) may appear constantly on the LCD/LED screen. This is a structural property of the LCD/ LED panel and is not a malfunction.
Optional Equipment Batteries Do not install optional equipment too close to the TV set. Keep optional equipment at least 11.875 inches (30 cm) away from the TV set. If a VCR is installed in front of the TV set or beside the TV set, the picture may become distorted. Picture distortion and/or noisy sound may occur if the TV set is positioned in close proximity to any equipment emitting electromagnetic radiation. Do not dispose of batteries in a fire.
Install on the wall Sound 11 7/8 inches 30 cm If a snapping or popping sound from the TV is continuous or frequent while the TV is operating, unplug the TV and consult your dealer or service technician. It is normal for some TV’s to make occasional snapping or popping sounds, particularly when being turned on or off. ? 4 inches 10 cm ding~ 4 inches 10 cm Pong~ Leave at least this space around the set.
Dolby License Notice and Trademark Acknowledgement Volume Adjustment Adjust the volume so as not to trouble your neighbors. Sound carries very easily at night. Therefore, closing the windows or using headphones is suggested. When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Contents in the Box After unpack the TV box, please check the TV and all accessories are well presented and undamaged.
Controls & Connections Volume + Volume - Channel 1. VOL + Press to increase the sound volume level. 2. VOL - Press to decrease the sound volume level. 3. CH ▲ Press to select the next higher program number. 4. CH ▼ Press to select the next lower program number. 5. MENU Press to open or exit the OSD (on-screen display) menu. 6. INPUT Press to select the input source. Channel Menu Input Speaker Power Indicator Speaker Power IR Receiver 7.
Buttons located at the right side of the TV will operate the same as these buttons on the remote control. Button COMP Description POWER Press to turn on and off the TV. TV/ AV/ COMP/ HDMI/ PC Press TV, AV, COMP or HDMI/PC separately to select the input directly. 0-9 Press 0-9 to select a channel; the channel changes after two seconds. PRE CH Press to go back to the previous TV channel or exit from the OSD when displaying menu items and settings. VOL +/- Press to adjust the volume.
Set-Up Inserting Batteries into the Remote control Insert two size AAA batteries (supplied) to the diagram inside the battery compartment of the remote control. Attaching the Base IMPORTANT: The Base of the AOC HDTV must be assembled prior to usage. 1. Place the TV set facing down on a soft and flat surface (blanket, foam, cloth, etc.) to prevent any damage to TV set. 2. Carefully align and insert the Base to the stand 3. Gently push the Base towards the TV until the locking mechanism locks into place.
Connecting TV Cable System or VHF/UHF Antenna System You can enjoy standard-definition and high-definition digital programming (if available in your area), along with standard-definition analog programming. This TV is capable of receiving unscrambled digital programming for both cable and external VHF/UHF antenna. It is strongly recommended that you connect the antenna/cable input using a 75-ohm coaxial cable to receive optimum picture quality.
Composite/ S-Video Signal Connection AV IN AV AV IN S-VIDEO S-VIDEO S-VIDEO Audio S-VIDEO PC Connection Use the TV as a monitor for your PC shown below with the HD15 to HD15 connection. This TV can also be connected to a PC with DVI or HDMI output. (Refer to the separate Quick Setup Guide.) VGA IN PC Connect the PC IN jack to the PC using the HD15- HD15 cable with ferrite core (analog RGB) and audio cable.
PC Input Signal Reference Chart After connecting the PC to the TV, set the output signal from the PC according to the chart below. Presetting PC Mode Standard Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) VESA VESA VESA VESA VESA VESA VESA VESA VESA 640 x 480 800 x 600 1024 x 768 1280 x 720 1280 x 768 1280 x 1024 1440 x 900 1680 x 1050 1920 x 1080 31.469 37.879 48.363 44.772 47.396 63.981 55.469 65.29 67.5 59.94 60.317 60.004 59.855 59.995 60.02 59.901 59.
USING AOC TV Turning the TV On and Off You can turn on the TV by using power switch button on the TV set or on the remote controller. Initial Wizard (1/8) Please select language... English Spanish French Next Cancel Navigate: Select: OK Initial Setting When you first start up this AOC HDTV set, please follow the Initial Wizard to your AOC HDTV. 1. Selecting Language. Select your preferred language: English, Spanish or French 1 Press ▲/▼ to select “Language”, and press OK. 2. Selecting Time mode.
A. Selecting Time Zone. Inital Wizard (3/8) Please select Time Zone... NST MST AST PST EST CST AKST HST Previous Cancel Navigate: 1 Select: OK Press ▲/▼/◄/► to select “Time Zone” which you located then press OK.
B. Manually enter the time. Initial Wizard (3/8) Please enter the time... Year 2010 Month Jan Day 1 Time 12:02 AM OK Previous Cancel Navigate: Select: OK Year 1 Press ▲/▼ to select “Year” then press OK. 2 Press ◄/► to adjust then press OK. Month 1 Press ▲/▼to select “Month” then press OK. 2 Press ◄/► to adjust then press OK. Day 1 Press ▲/▼ to select “Day” then press OK. 2 Press ◄/► to adjust then press OK. Time 1 Press ▲/▼ to select “Time” then press OK.
3. Select “Eco” mode or “Vivid” mode. When you turn on TV in the first time, you can choose “Eco” mode to decrease backlight level to save the power consumption or “Vivid” mode to enhance picture contrast and sharpness. Initial Wizard (4/8) Please select Eco/Vivid mode... Eco Vivid Previous Cancel Navigate: 1 Select: ENTER Press ▲/▼ to select “Eco” or “Vivid” for display setting. 4. Select TV RF tuning band. Initial Wizard (5/8) Please select TV RF tuning band...
5. Search TV channel Initial Wizard (6/8) Please check if RF cable is connected properly... Start Previous Cancel Navigate: 1 Select: OK Press ▲/▼ to select “Previous” or “Cancel” for RF Tuning setting. Press OK will execute channel searching. Initial Wizard (7/8) Searching, Please wait... Searching Analog CH CH 100 Analog Channels Found 66 Digital Channels Found 55 100% Cancel Navigate: 1 Select: OK Press ▲/▼ to select “Cancel” for RF Tuning setting.
Viewing Mode Selection For TV input with SD programs Normal Mode Zoom1 Mode Suitable for viewing conventional 4:3 programs in their normal format. Use these aspect modes to zoom in and to reduce the black bars. Wide Mode Zoom2 Mode The original content in this mode has to fill the entire screen of the display. Use these aspect modes to zoom in and to reduce the black bars. For TV input with HD programs Normal Mode Zoom1 Mode Suitable for viewing conventional 4:3 programs in their normal format.
Switching Input Source On AOC TV, you can choose signal source on the remote control directly, or press “Source” to choose the signal source on the display menu. 1. When choosing signal source on the remote control directly: Press the following keys to switch input source. COMP COMP PRE!CH Add Fav Display Fav M EN U / Exit Wide EPG MTS CC 2. When using “Source” key to choose signal source: COMP Source List 0. TV 1. AV PRE!CH 2. Component 3. VGA 4.
OSD Manual Setting Channel Search CHANNEL Cable Tuning Band Channel Strength Auto CH Search Add on CH Search Channels List Channel Labels FAV Channel Setting Move 1 M EN U / Exit OK Select Return MENU /Exit Exit Press MENU to call out MENU. 2 Press ▲/▼ to select “Channel” , and press OK. 3 Press ▲/▼ to select “Auto CH Search”, and then press OK. The submenu of CHANNEL menu in TV mode shows as below. 1) Tuning Band: Select TV source signal from the Air (antenna) or Cable (CATV).
Changing Channel/Flashback On AOC TV, you can change channel on the remote control directly, or press CH ▲/▼ on the side of the TV to choose the channel. 1. Press the number keys directly to change the channel. PR 2. Press the CH to change channel. 3. Press PRE CH to go to the previous channel.
Changing Volume, Mute and Sound Mode 1. Press VOL to change the volume. 2. Press MUTE to mute the TV. 3. Press Audio to change surround mode: Music, Speech and Personal. For more details, please refer to “Adjust Audio Setting”.
Adjust Video Setting VIDEO Eco Picture Mode Brightness 48 Contrast 48 Sharpness 50 Color 63 Tint 0 Color Temp Move 1 M EN U / Exit Cool OK Select Return MENU /Exit Exit Press MENU/EXIT to call out MENU. 2 Press ▲/▼ to select “VIDEO” 3 Press ▲/▼ to select Video Settings: Picture Mode, Brightness, Contrast, Sharpness, Color, Tint, Color Temp, Noise Reduction, Adaptive Contrast, DCR, Backlight, Aspect Ratio, Preset, and press OK to enter. 4 Press ◄/► to adjust.
Adjust Audio Setting AUDIO Personal Sound Mode Bass 32 Treble 32 Balance 0 Audio Source Stereo SPDIF PCM On Speaker Move 1 M EN U / Exit OK Select Return MENU /Exit Exit Press MENU/EXIT to call out MENU. 2 Press ▲/▼ to select “Audio” 3 Press ▲/▼ to select Audio Settings˖Sound Mode, Bass, Treble, Balance, Audio Source, Audio Language, SPDIF, Speaker, Multi Language, AVL, Preset, and press OK to enter. 4 Press ◄/► to adjust.
Adjust PC Setting This setting is only available in PC mode. VGA H-Position 17 V-Position 13 Clock 8 Phase 2 Auto Adjust Preset Move 1 M EN U / Exit OK Select Return MENU /Exit Exit Press MENU/EXIT to call out MENU. 2 Press ▲/▼ to select “PC” 3 Press ▲/▼ to select PC Settings: H. Position, V. Position, Clock, Phase, Auto Adjust, Preset, and press OK to enter. 4 Press ◄/► to adjust. 5 M EN U / Exit , and press OK. Press MENU/EXIT again to exit. PC Setting H.
Feature Setup FEATURE English Menu Language Time Password Setting Parental Control Closed Captions Off Analog Captions CC1 SERVICE1 Digital Captions Move 1 M EN U / Exit OK Select Return MENU /Exit Exit Press MENU/EXIT to call out MENU. 2 Press ▲/▼ to select “Setup” 3 Press ▲/▼ to select Setting items: Menu language, Time, Password Setting, Parental Control, Closed Captions, Analog Caption, etc. and press OK to enter. 4 Press ◄/► to adjust. 5 M EN U / Exit , and press OK.
2 Press ◄/► to adjust Auto or Manual setting for Time Mode and press OK. 3 Press ▲/▼ to select “Time Zone”. Press ◄/► to adjust Time Zone which you located and press OK. 4 Press ▲/▼ to select “Daylight Savings”. Press ◄/► to on/off Daylight Savings and press OK. 5 For manually Time Mode setting, press ▲/▼ to select “Year”, “Month”, “Day”, and “Time”. Press ◄/► to adjust “Year”, “Month”, “Day”, and “Time”, and press OK. M EN U / Exit 6 Press MENU/EXIT again to exit. 3.
4. Parental Control: FEATURE Parental Control Button Lock Off Block Unrated TV Off USA Parental Locks Canadian Parental Locks Open V-Chip Move OK Select Return MENU /Exit Exit Provide the Parental Control (V-chip) function setting. Before entering the Parental Control sub-menu, user has to key in the password first. Enter the Parental Lock item, then the user can modify the restricted table about MPAA or TV Rating respectively.
9. HDMI CEC: Set the HDMI Control to ON and this feature will enable the HDMI CEC function and your AOC HDTV will discover and communicate automatically with other compatible HDMI interfaced devices. Select ODD to disable this option. FEATURE HDMI CEC HDMI Control On Device Auto Off Off TV Auto On Off Root Menu Device List Move 1 M EN U / Exit OK Select Return MENU /Exit Exit Press MENU/EXIT to call out MENU.
JPEG Viewer After plugging USB storage device into USB port, Multimedia List menu will display, or press “Photo” on the remote control after you plugging USB storage device. Image Delay Normal Start Slide Show \.. Filename Filename Filename Filename Filename Rotate Photo Back To Upper Folder Back To Root Folder Exit 1 Press OK to enter JPEG Viewer. 2 Press ▲/▼/◄/►to select, and press OK to enlarge the selected photo (orange frame) browser.
Troubleshooting Condition No picture No picture Cannot receive any channels TV is locked to one channel Cannot receive or select The TV turns off No picture from some video Poor picture The quality of the images is not as good as what I saw at the store Double images or ghosts Only snow and noise appear on the screen Dotted lines or stripes No color/Dark picture/Color is not correct/The picture is too bright Noisy picture Explanation / Solution Check the Power Saving settings.
Dimensions & Specifications Model LE22H067 / LE24H067 Panel size LE22H067: 546 mm diagonal (21.5” viewable) LE24H067: 598 mm diagonal (23.
P Index Panel size, 35 PC Connection, 14 PC Setting, 28 Personal, 25 Phase, 10, 28, 34 Picture Mode, 34 Picture Setting, 26 Power, 4, 5, 34 Preset, 15, 26 Presetting PC Mode, 15 Presetting Video Mode, 15 A Adaptive Contrast, 26 Antenna, 6, 35 Aspect Ratio, 26 Audio, 25, 27, 34 Audio Language, 27 Audio Setting, 25, 27 Audio Source, 27 Auto Adjust, 28 Auto Search, 23 AVL, 27 R Remote Control, 11, 16, 22, 24, 26, 34 Reset All, 29 Resolution, 15, 35 B BACK, 11 Backlight, 26 Balance, 27 Bass, 27 B/L control