Installation and Operation J Type Power Conditioner and Battery Backup J25B J35B 120 V 1440 VA/865 W
General Information ........................................................ 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Information Overview The APC by Schneider Electric J Type Power Conditioner protects audio-video systems from power spikes and surges. The J Type has noise filter banks, which reduce electromagnetic interference to ensure the best picture and sound quality. The unit also provides clean and safe power to connected equipment in the event of a power outage. Inventory Safety Electrical Hazard: For indoor use only. • Risk of electric shock. Do not plug into another relocatable power tap. • Overloading.
Product Overview av022a Front panel 1 SETUP button - Push to scroll through the Setup menu screens. Press and hold for three seconds to save the current screen as the default screen. 2 STATUS button - Push to scroll through the menu screens. Press and hold for 10 seconds to view the Diagnostic menu screens. 3 LCD Display 4 ON/OFF button - Push this button to apply power to the outlets. The unit will continue to provide surge protection when the unit is turned on or off.
Installation Connect Battery 3 av025a av026a 6 av027a 5 bu059a 4 av025a 2 av023a 1 av028a 7 Connect Input Power Note: If the unit is connected to input power and is OFF, it will still provide protection from power surges and spikes. Use the input power cord to connect the unit to input power. If the unit is functioning properly, the display will illuminate. Connect the other end to a grounded, 120 Vac receptacle.
Power-Saving Master and Controlled outlets (J35 models only) When the power-saving feature is enabled, the J35B reduces power consumption by automatically disconnecting utility power to devices that are not in use. When the device connected to the Master outlet goes into sleep or standby mode, the J35B will disconnect power to components connected to the Controlled by Master outlets, conserving energy.
Operation Display Interface Menus Start up menu screens At initial start up, the LCD screen will scroll through several menu screens and perform a self test. APC - Legendary Reliability J35 PWR CONDITNR WITH BATT BACKUP SELF TEST ON.... ON-LINE TEST SELF TEST ON.... ON-BATTERY TEST SELF TEST RSLT: TEST HAS PASSED Status menu The Status menu shows the overall status of the unit and of each outlet on the unit. Push the STATUS button to move to the next screen. Use the arrow keys to scroll up and down.
Estimate run time and current battery charge. As the battery charge increases, the battery run time will also increase. EST RUN T: 4 MIN 50% System load. The system load indicates how much power is being used by the connect equipment. The percentage indicates the amount of the unit capacity currently being used. SYS LOAD: 900W 90% Input and output voltage. INPUT VOLT: 120V OUTPUT VOLT: 120V INPUT Hz: 60Hz OUTPUT Hz: 60Hz Model number and firmware. MDL#: J35B AV UPS FW VER: 874.P0.D Serial number.
Audio alarm. Change the alarm setting to on or off. The unit will emit an audible beep if there is a fault or if the unit changes to operate on battery, has a low battery condition, or is overloaded. AUDIO ALARM: OFF PRESS TO CHNG Sensitivity. Select Low, Medium, or High to determine how often the until will switch to battery power. If the sensitivity it set to Low, the unit will tolerate more fluctuations in power, and will switch to battery less often.
Green function - transfer threshold. Configure the master outlet to recognize when the master device has gone into sleep or standby mode. Configure the delay between when the Master unit turns off and the peripheral units turn off. MASTER THRES: 25W PRESS TO CHNG CON ONDLY: 4 SEC PRESS TO CHNG CON OFFDLY: 4 SECPRESS TO CHNG Low battery warning. Set the time at which the unit will provide an audible warning that it almost exhausted battery power.
Troubleshooting Problem Possible Cause The unit will not turn on. The unit is not connected to utility power. The internal battery is not connected. Ensure that essential equipment is not plugged into a SURGE ONLY outlet. The unit does not provide power during a utility power outage. The unit is operating on The plug has partially pulled out of the battery power, while connected wall outlet, the wall outlet is no longer to utility power. receiving utility power, or the circuit breaker has been tripped.
Specifications Input/Output J25B J35B Nominal Voltage Input/Output Current Frequency Number of Outlet Receptacles Dimensions (H x W x L) 120 V 12 A 47 - 63 Hz 8 (6 battery backup, 2 surge only) 9.76 cm x 43.18 cm x 40.64 cm (3.84 in x 17 in x 16 in) 2.43 m (8 ft.) right angle NEMA 5-15 plug 120 V 12 A 47 - 63 Hz 8 (6 battery backup, 2 surge only) 9.76 cm x 43.18 cm x 40.64 cm (3.84 in x 17 in x 16 in) 2.43 m (8 ft.
Información general Descripción general El acondicionador de alimentación tipo J de APC by Schneider Electric protege los sistemas de audio y vídeo contra los picos y subidas de tensión. El acondicionador tipo J cuenta con bancos de filtros de ruido, que reducen las interferencias electromagnéticas para garantizar la mejor calidad de imagen y sonido. La unidad también proporciona alimentación limpia y segura a los equipos conectados en caso de que se produzca una interrupción en el suministro eléctrico.
Componentes av022a Vista delantera 1 Botón de CONFIGURACIÓN: Pulse este botón para avanzar por las pantallas del menú de configuración. Manténgalo pulsado durante tres segundos para guardar la pantalla actual como pantalla predeterminada. 2 Botón de ESTADO: Pulse este botón para avanzar por las pantallas de menús. Manténgalo pulsado durante 10 segundos para ver las pantallas del menú de diagnósticos. 3 Pantalla LCD.
Instalación Conexión de la batería av026a 6 av027a 5 bu059a 4 av025a 3 av025a 2 av023a 1 av028a 7 Conexión de la alimentación de entrada Nota: Si la unidad está conectada a alimentación de entrada y está apagada, seguirá ofreciendo protección contra los picos y subidas de tensión. Utilice el cable de alimentación de entrada para conectar la unidad a la alimentación de entrada. Si la unidad funciona correctamente, se encenderá la pantalla.
Salidas principal y controladas de ahorro de energía (sólo unidades J35) Cuando la función de ahorro de energía está activada, la unidad J35B desconecta automáticamente la alimentación de la red eléctrica hacia los dispositivos que no se utilizan para reducir el consumo de energía.
Funcionamiento Menús de la interfaz de pantalla Pantallas de menús de inicio Cuando la unidad se inicie por primera vez, en la pantalla LCD se mostrarán varias pantallas de menús y se realizará una prueba automática. APC - Fiabilidad legendaria ACONDICIONADOR DE ALIMENTACIÓN J35 CON RESERVA DE BATERÍA PRUEBA AUTOMÁTICA ACTIVADA.... PRUEBA EN LÍNEA PRUEBA AUTOMÁTICA ACTIVADA....
Tiempo de autonomía estimado y carga actual de la batería. A medida que aumente la carga de la batería, también aumentará el tiempo de autonomía de la misma. TIEMPO DE AUTONOMÍA ESTIMADO: 4 MIN 50% Carga del sistema. La carga del sistema indica la cantidad de alimentación que consumen los equipos conectados. El porcentaje indica la capacidad de la unidad que se está utilizando en ese momento. CARGA DEL SISTEMA: 900 W 90% Tensión de entrada y salida.
Alarma sonora. Puede configurar la alarma en encendida o apagada. La unidad emitirá un pitido si se produce un fallo o si la unidad pasa a funcionamiento en batería, el nivel de la batería es bajo o está sobrecargada. ALARMA SONORA: DESACTIVADA PULSAR PARA CAMBIAR Sensibilidad. Seleccione Low (baja), Medium (media) o High (alta) para determinar la frecuencia con la que la unidad pasará a alimentación de batería.
Umbral de transferencia de la función ecológica. Configure la salida principal para que reconozca el momento en el que el dispositivo principal se sitúa en modo de hibernación o en espera. Configure el retraso entre el momento en el que la unidad principal se apaga y las unidades de periféricos también se apagan. UMBRAL PRINCIPAL: 25 W PULSAR PARA CAMBIAR CONFIGURACIÓN ACTIVADA DEL RETRASO: 4 S PULSAR PARA CAMBIAR CONFIGURACIÓN DESACTIVADA DEL RETRASO: 4 S PULSAR PARA CAMBIAR Advertencia de batería baja.
Resolución de problemas Problema La unidad no se enciende. La unidad no proporciona alimentación durante una interrupción del suministro de red. La unidad funciona con alimentación de batería cuando está conectada al suministro de red. Posible causa La unidad no está conectada al suministro de red. La batería interna no está conectada. Compruebe que los equipos esenciales no estén conectados a una salida que sólo ofrezca PROTECCIÓN CONTRA SOBRETENSIONES.
Especificaciones Entrada/salida J25B J35B Tensión nominal Corriente de entrada/salida Frecuencia Número de receptáculos de salida 120 V 12 A 47 – 63 Hz 8 (6 de reserva de batería y 2 de protección contra sobretensiones solamente) Dimensiones (altura x anchura x longitud) Cable de alimentación 9,76 cm x 43,18 cm x 40,64 cm (3.84 in x 17 in x 16 in) De 2,43 m (8 ft.
Informations générales Présentation Le conditionneur d’alimentation de type J d’APC by Schneider Electric protège les systèmes audio/vidéo des transitoires et surtensions. Le modèle type J est doté de filtres antibruits, qui limitent les interférences électromagnétiques afin de garantir une qualité de son et d’image optimale. L’appareil offre en outre une alimentation propre en toute sécurité des équipements reliés en cas de panne secteur.
Composants av022a Vue de face 1 Bouton CONFIGURATION : appuyez sur ce bouton pour naviguer dans le menu de configuration. Maintenez-le enfoncé pendant trois secondes pour définir l’écran affiché comme écran par défaut. 2 Bouton ETAT : appuyez sur ce bouton pour naviguer dans le menu correspondant. Maintenez-le enfoncé 10 secondes pour afficher les écrans du menu Diagnostics. 3 Ecran LCD. 4 Bouton MARCHE/ARRET : appuyez sur ce bouton pour alimenter les prises.
Installation Connexion de la batterie 3 av025a av026a 6 av027a 5 bu059a 4 av025a 2 av023a 1 av028a 7 Connexion de l’alimentation d’entrée Remarque : si l’appareil est relié à une alimentation d’entrée et est hors tension, il continue de protéger les équipements reliés contre les surtensions et les transitoires. Reliez l’appareil à l’alimentation à l’aide du cordon d’alimentation d’entrée fourni. Si l’appareil fonctionne correctement, l’écran s’allume.
Prise principale et prises contrôlées à économie d’énergie (modèle J35 uniquement) Lorsque le mode économie d’énergie est activé, le J35B réduit la consommation électrique en déconnectant automatiquement du secteur les équipements non utilisés. Lorsque l’équipement relié à la prise principale passe en mode veille, le J35B interrompt l’alimentation des équipements reliés aux prises contrôlées par la prise principale afin d’économiser l’énergie.
Fonctionnement Menus de l’interface d’affichage Ecrans du menu de démarrage Au démarrage initial, l’écran LCD affiche une série d’écrans de menu et procède à un test automatique. APC - Légendaire Fiabilité CONDITIONNEUR D'ALIMENTATION J35 AVEC BATTERIE DE SECOURS TEST AUTOMATIQUE ACTIVÉ... TEST EN LIGNE TEST AUTOMATIQUE ACTIVÉ... TEST AVEC LA BATTERIE RÉSULTAT DU TEST AUTOMATIQUE : TEST RÉUSSI Menu Status (Etat) Le menu Status affiche l’état général de l’appareil et de chacune des prises.
Autonomie estimée et charge de la batterie. L’autonomie de la batterie augmente à mesure que sa charge augmente. TEMPS DE FONCTIONNEMENT ESTIMÉ : 4 MIN 50% Charge du système. La charge du système indique la puissance utilisée par les équipements reliés. Le pourcentage indique la proportion de la capacité totale de l’appareil actuellement utilisée. CHARGE DU SYSTÈME : 900 W 90% Tension d’entrée et de sortie.
Alarme sonore. Activez ou désactivez l’alarme sonore. Une alarme sonore retentit en cas de panne, si l’appareil passe en mode d’alimentation sur batterie, si la batterie est faible ou en cas de surcharge. ALARME SONORE : DÉSACTIVÉE APPUYEZ SUR POUR MODIFIER Sensibilité. Sélectionnez le degré de sensibilité (Low, Medium ou High) pour déterminer le seuil auquel l’appareil passe en mode d’alimentation sur batterie.
Mode économie d’énergie - seuil de transfert. Configurez la prise principale pour qu’elle détecte le passage de l’équipement principal en mode veille. Configurez le délai entre la mise hors tension de l’équipement principal et celle des périphériques. SEUIL PRINCIPAL : 25 W APPUYEZ SUR POUR MODIFIER CON ONDLY : 4 S APPUYEZ SUR POUR MODIFIER CON OFFDLY : 4 S APPUYEZ SUR POUR MODIFIER Avertissement batterie faible.
Dépannage Problème L’appareil ne s’allume pas. L’appareil ne fournit aucune alimentation lors d’une coupure de courant secteur. Cause probable L’appareil n’est pas raccordé à l’alimentation secteur. La batterie interne n’est pas connectée. Assurez-vous que l’équipement principal n’est pas branché sur une prise PROTEGEE CONTRE LES SURTENSIONS.
Caractéristiques Entrée/Sortie J25B J35B Tension nominale Courant d’entrée/sortie Fréquence Nombre de prises électriques 120 V 12 A 47 - 63 Hz 8 (6 sur la batterie de secours, 2 protégées contre les surtensions) 9,76 cm x 43,18 cm x 40,64 cm (3,84 in. x 17 in. x 16 in.) À angle droit, prise NEMA 5-15, 2,43 m (8 ft) 120 V 12 A 47 - 63 Hz 8 (6 sur la batterie de secours, 2 protégées contre les surtensions) 9,76 cm x 43,18 cm x 40,64 cm (3,84 in. x 17 in. x 16 in.
APC Worldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways: • Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer support requests. – www.apc.com (Corporate Headquarters) Connect to localized APC Web sites for specific countries, each of which provides customer support information. – www.apcav.com APC Audio/Visual Technical Support – www.apc.