User Manual

2/6
Before Installation:
1. Ensure electrical connections, water supply lines and waste connections are both compatible with this product, and their installation completed and
ready for connection the before installation of this product. Review the specifications within this document, other documentation supplied,
specifications listed on the packaging of this product, and technical specifications listed on the individual components. If there are any further
questions contact your place of purchase. The (optional) drain hose size is 1.5-inches (40mm); the water inlet connections with (optional) hoses are ½-
inch National Pipe Thread (NPT/FIP/MIP).
2. Before connecting the water supply lines, briefly flush the water lines to free any loose particles that may have built up throughout the years, or may
have fallen in during new construction.
3. Ensure the water supply lines for this product has its own dedicated water shutoff valves installed in an accessible location.
4. Ensure there is access to and enough space to connect, adjust or fasten the various supply lines, waste line and other components.
5. After extracting the product and parts from the packaging, check that all parts are complete and that there are no visible errors, missing parts, or
damages. Any damages are required to be reported within 72-hours of delivery.
6. Bathtubs are already leak tested from the factory, but should always be leak tested again after shipping.
7. Computerized systems and electrical components are already function tested from the factory, but should always be tested again before installation.
Installation Instructions:
1. Be sure to check each installation step with this manual to ensure the product is installed correctly. The product must be installed with all the
feet or supportive legs touching the floor before any use. Leveling the product is an important procedure and must be completed on-site, .... on
the installation surface and final installation position.
2. Only a professional electrician is recommended to work on the electrical portions of installation and testing.
3. Electrical service must meet the requirements listed on the components of the product, listed within this manual, or otherwise advised based
on a thorough analysis of any special circumstances.
4. An electrical protection device for short-circuits, power overloads or incorrect voltage must be installed and used in conjunction with this
product.
5. Do not cut or extend electrical wires or power-cord of the product without the approval of a professional electrician and warranty service
representative.
6. Do not disassemble the control panel or computer controller as it is not designed for disassembly. Defects, damages or shock caused by such
removal cannot be the responsibility of the supplier or its distributors.
7. Local standards and codes must be followed and cannot be the responsibility of the supplier or its distributors.
8. The motor must be grounded with wire not less than 14awg (1.63mm-diameter) or otherwise required in accordance to local codes.
9. Appliances or components with ground or “earth” connections must be installed and used in conjunction with the product, and connected
in
accordance to local codes.
10. Other electrical components, except the remote control device (optional), should be kept, located or affixed away from the product, so they
cannot fall into the bath, while in use.
11. This product or any appliance used near this product must be used in conjunction with a Ground Fault Circuit Interrupter
(“G.F.C.I.” or “G.F.I.”) or Residual Current Device (“R.C.D.”) with a trip current of not greater than 30mAor otherwise required in accordance to local
codes.
12. Always double-check all connections to ensure for proper installation, tension, and connection, including parts, plugs, hoses, nuts, screws,
wires, etc.
13. Check local and national requirements before installing or purchasing this product.
14. “H” hot (red) and “C” cold (blue) water supply connections and their orientation are critical to proper function of this product.
15. Ensure the (optional) “H” hot (red) and “C” cold (blue) water hoses will not touch the floor when this product is fully installed, as it may cause
rusting and possibly weakening of those hoses.
16. Harsh chemicals such as acetone, ammonia or gasoline can possibly dissolve or damage portions of this product – do not use such
chemicals for cleaning or installing this product.
17. Do not stack anything on top of this product, use it for support, or apply any extreme pressure to critical areas that may cause misalignment
or damage; take special care when moving this product.