Instruction Manual

ManualsBrandsAries Automotive ManualsFor the car364009-2

PARTS LIST:

INSTALLATION INSTRUCTIONS

1999-11 1500-2500-3500 SILVERADO/SIERRA EXT CAB (Standard Box)

PART NUMBER 364009/364009-2

1 Passenger Side Bar 2 Front Support Bracket 2011

1 Driver Side Bar 2 Center Support Brackets 2011

1 Passenger Side Front Mounting Bracket 2 Rear Support Brackets 2011

1 Driver Side Front Mounting Bracket 2 10-1.5mm x 47mm bolt tab (14mm W x 30mm L)

1 Passenger Side Center Mounting Bracket 21 10-1.50mm x 30mm Hex Head Bolts

1 Driver Side Center Mounting Bracket 10 10mm Hex Nuts

1 Passenger Side Rear Mounting Bracket 24 10mm Lock Washers

1 Driver Side Rear Mounting Bracket 32 10mm ID x 22mm OD x 1.5mm Flat Washers

2 Front Support Bracket 99-10 2 10mm Nut Plates

2 Center Support Brackets 99-10 2 12-1.75mm x 30mm Hex Head Bolts

1 Passenger Side Rear Support Bracket 99-10 2 12mm Hex Nuts

1 Driver Side Rear Support Bracket 99-10 4 12mm ID x 29mm x 3mm Flat Washers

1 1/4" x 1 3/4” x 1 3/4" square flat washer 99-10 2 12mm Lock Washers

2 M38 x 38 Square Plastic Retainers 2 10mm x 35mm Bolt Tabs

Dri

ver Side

Center Bracket

Passenger Side

Center Bracket

Dri

ver Side

Rear Bracket

Passenger Side

Rear Bracket

99-10 Pass

enger Side

Front Support Bracket

99-10 Driver Side

Front Support Bracket

Driver Side

Front Bracket

Passenger Side

Front Bracket

99/10 Passenger

Rear Brace Bracket

99/10 2500

Passenger Rear

1/4" x 1 3/4” x 1 3/4"

10mm x 47mm Bolt tabs

10mm x 35mm Bolt

Plate (with Plastic

retainer installed)

99-10Ce

nter Support Brackets 10mm Nut Plates

2011 Passenger Side

Front Support Bracket

2500/3500 Models

2011 Passenger Side

Middle Support Bracket

2500/3500 Models

2011 Driver Side

Middle Support Bracket

2500/3500 Models

2011 Driver Side

Front Support Bracket

2500/3500 Models

1999-10 models

Driver Rear

Brace Bracket

2011 models

Passenger Rear

Brace Bracket

2011 models

Driver Rear

Brace Bracket

Page 1 of 6 12/13/2010

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 1999-11 1500-2500-3500 SILVERADO/SIERRA EXT CAB (Standard Box) PART NUMBER 364009/364009-2 PARTS LIST: 1 1 1 1 1 1 1 1 2 2 1 1 1 2 Passenger Side Bar Driver Side Bar Passenger Side Front Mounting Bracket Driver Side Front Mounting Bracket Passenger Side Center Mounting Bracket Driver Side Center Mounting Bracket Passenger Side Rear Mounting Bracket Driver Side Rear Mounting Bracket Front Support Bracket 99-10 Center Support Brackets 99-10 Passenger Side Rear Support Bracket 99-10
PAGE 2
PROCEDURE: 1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. 2. From underside of vehicle remove front, center, and rear body mount bolts. Do not remove bushings. 3. Hang driver side front, center and rear Mounting Brackets into position by partially threading factory body mounting bolts back into body mounts (Fig 1). 4. Locate the two factory holes in the bottom of the frame towards the front of the vehicle.
PAGE 3
11.
PAGE 4
99-10 2500 Model Front Installation Pictured Fig 5 99-10 2500 Model Front Installation Pictured Fig 6 10mm x 30mm Hex bolt 10mm Flat Washers 10mm Lock Washer 10mm Hex nut Push up 2011 2500 Model Front Installation Pictured Fig 7 Nut plate 2011 2500 Model Center Installation Pictured Fig 7A 10mm x 30mm Hex bolt 10mm Flat Washers 10mm Lock Washer 1500 Model Center Installation Pictured Fig 8 12mm x 30mm Hex bolt 12mm Hex nut 12mm Flat Washers 12mm Lock Washer 10mm x 30mm Hex bolt 10mm Flat Wash
PAGE 5
2011 2500 Model Center Installation Pictured 2011 2500 Model Center Installation Pictured Fig 10 Fig 10A 10mm bolt tab 10mm Flat Washers 10mm Lock Washer 10mm Nut Place 10mm bolt tab in hole.
PAGE 6
Driver side shown Fig 13B Fig 14 Driver side rear brace 10mm Hex nut 10mm Flat Washers 10mm Lock Washer 10mm x 30mm Hex bolt, 10mm Lock Washer 10mm Flat Washer 10mm x 30mm Hex bolt 10mm Hex nut 10mm Flat Washers 10mm Lock Washer Installation Complete Page 6 of 6 12/13/2010
PAGE 7
INSTALLTION ALERT General Motors has made changes to their late model 2010 and 2012 Chevrolet Silverado and GMC Sierra Light Duty and Heavy Duty Trucks and these changes affect the installation of our Side Bars. Currently, all Side Bars manufactured for GM trucks use the factory body mount bolts to attach the bars and brackets to the truck. In years past, GM used a fixed nut that was welded in place to the chassis of the truck.