User guide

ManualsBrandsAries Automotive ManualsCar4051

Page 1 of 4 9/20/07 (AM)

Top Brackets

02-06 Trailblazer Models

PARTS LIST:

1 Grille Guard 4 10-1.50mm x 30mm Hex Head Bolts

1 Driver/Left Mounting Bracket 4 10mm Nylock Nuts

1 Passenger/Right Mounting Bracket 8 10mm ID x 26mm OD x 3mm Flat Washers

1 Driver/Left 07-08 Models Top Bracket 2 8-1.25mm x 30mm Hex Head Bolts

1 Passenger/Right 07-08 Models Top Bracket 2 8mm Nylock Nuts

2 02-06 Models Top Brackets 4 8mm ID x 29mm OD x 3mm Fender Washers

6 12-1.75mm x 35mm Hex Head Bolts 2 6-1.00mm x 20mm Allen Bolts

6 12mm Nylock nuts 2 6mm Nylock Nuts

12 12mm ID x 29mm OD x 3mm Flat Washers 4 6mm ID x 18mm OD x 1.5mm Flat Washers

INSTALLATION INSTRUCTIONS

GRILL GUARD PART # 4051-2/4051

02-09 CHEVY TRAILBLAZER

Driver Side Passenger Side

Top Brackets

07-09 Trailblazer Models

Driver Side

Mounting Bracket

Passenger Side

Mounting Bracket

To Grille

Guard

To Vehicle

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS GRILL GUARD PART # 4051-2/4051 02-09 CHEVY TRAILBLAZER PARTS LIST: 1 1 1 1 1 2 6 6 12 Grille Guard Driver/Left Mounting Bracket Passenger/Right Mounting Bracket Driver/Left 07-08 Models Top Bracket Passenger/Right 07-08 Models Top Bracket 02-06 Models Top Brackets 12-1.75mm x 35mm Hex Head Bolts 12mm Nylock nuts 12mm ID x 29mm OD x 3mm Flat Washers 4 4 8 2 2 4 2 2 4 10-1.50mm x 30mm Hex Head Bolts 10mm Nylock Nuts 10mm ID x 26mm OD x 3mm Flat Washers 8-1.
PAGE 2
PROCEDURE: 1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. 2. NOTE: The factory bottom bumper air dam must be permanently removed or optional cutting required to install this Grille Guard. If you are removing, use a flat screw driver to remove one push type fasteners on each side; then gently pull air dam towards the front of the vehicle to unfasten clips. If you are cutting, remove air dam and set on clean working area.
PAGE 3
(Driver Side Installation Shown) Remove factory Nut Clip with Bolt 22” Leave a ¼” here Fig 1 Fig 2 Bracket mounting location 8mm x 30mm Hex Bolt 8mm Nylock Nut 8mm Fender Washers 10mm x 30mm Hex Bolt 10mm Nylock Nut 10mm Flat Washers Driver Side Mounting Bracket Fig 3 Factory Bolt Factory Grille Shell Fig 4 Remove the four factory screws from across the grille shell’s top Fig 5 Page 3 of 4 9/20/07 (AM)
PAGE 4
Top Bracket Top Bracket Fig 6 Fig 7 Fig 8 Fig 9 12mm x 35mm Hex Bolts 12mm Nylock Nuts 12mm Flat Washers 6mm x 20mm Allen Bolts 6mm Nylock Nuts 6mm Flat Washers Page 4 of 4 9/20/07 (AM)