INSTALLATION INSTRUCTIONS 2-1/2” SPORT BAR 2014-15 NISSAN ROGUE EXCLUDES 2014 “SELECT” MODEL PART # 9505
-1/2” SPORT BAR 2014-15 NISSAN ROGUE EXCLUDES 2014 “SELECT” MODEL PARTS LIST: Qty 1 1 1 1 1 2 2 2 2 2 Description Qty 2.5” Nudge Bar Driver/Left Frame Mounting Bracket Passenger/Right Frame Mounting Bracket Driver/Left Support Bracket Passenger/Right Support Bracket Flat Support Brackets 3/8” Special Self Tapping Bolts 12-1.75 x 50mm Hex Bolts 12mm x 30mm OD x 3mm Flat Washers 12mm Lock Washers 2 1 3 2 2 2 4 2 2 Description 10mm Threaded Inserts 10mm Insert Tool 10-1.
2-1/2” SPORT BAR 2014-15 NISSAN ROGUE EXCLUDES 2014 “SELECT” MODEL 6. Next, select the driver side Bent Support Bracket, (Figure 11). Hold the Bracket up in position to help locate the correct factory hole to attach it to, (see Figures 7, 13A & 14). Select (1) 10mm Threaded Insert, (1) 10mm Hex Bolt, (1) 10mm Flat Washer and (1) 10mm Insert Tool. Assemble the Tool at pictured in Figure 12, Push the Tool and Insert assembly into the factory hole.
2-1/2” SPORT BAR 2014-15 NISSAN ROGUE EXCLUDES 2014 “SELECT” MODEL 8mm x 35mm Hex Bolt (2) 8mm Flat Washers 8mm Lock Washer 8mm Hex Nut (Fig 3) Flat Support Bracket Front (Fig 4) Driver side mounting location for Support Bracket pictured from below Front (Fig 5) Driver side Frame Bracket Use factory hole for Threaded Insert to install Support Bracket Special 3/8” Self Tapping Flange Bolt Front (Fig 6) Driver side Frame Bracket mounting location Front Use 12mm Hex Bolt to temporarily line up Bracket
2-1/2” SPORT BAR 2014-15 NISSAN ROGUE EXCLUDES 2014 “SELECT” MODEL Front (Fig 8) Passenger Side Frame Bracket Special 3/8” Self Tapping Flange Bolt (Fig 9) Passenger Frame Bracket mounting location Use factory hole for Threaded Insert to install Support Bracket Front (Fig 10) Passenger Frame and Flat Bracket installed 10mm Hex Bolt 10mm Flat Washer Insert Tool Front (Fig 11) Driver side Support Bracket 10mm Threaded Insert Fig 12 Page 4 of 6 (DP) 6/9/14
2-1/2” SPORT BAR 2014-15 NISSAN ROGUE EXCLUDES 2014 “SELECT” MODEL Driver Side 10mm Threaded Insert installed for Support Bracket Front Fig 13A (Fig 13B) Insert fully installed 10mm Hex Bolt 10mm Lock Washer 10mm Flat Washer Use 12mm Hex Bolt to temporarily line up Brackets before final assembly Front Fig 14 Front Front (Fig 15) Passenger side Support Bracket (Fig 16) Passenger side Insert installed Page 5 of 6 (DP) 6/9/14
2-1/2” SPORT BAR 2014-15 NISSAN ROGUE EXCLUDES 2014 “SELECT” MODEL 10mm Hex Bolt 10mm Lock Washer 10mm Flat Washer 12mm Hex Bolt 12mm Lock Washer 12mm Flat Washer Front (Fig 17) Passenger side Support Bracket installed Front Front (Fig 18) Driver side installation pictured Front (Fig 19A) Hold plastic cover up to bottom of brackets. Mark location of brackets onto inside of cover Complete Installation (Fig 19B) Cut as little out of the cover as possible to clear Brackets.
