Manual

ManualsBrandsAries Automotive ManualsCarALC25001

PARTS LIST:

Qty Description Qty Description

1 Cargo Center section lid with keys 12 Philips machine screws

1 Passengers/right side plate 8 4mm x 10mm Button head bolts

1 Drivers/left side plate 8 4mm Lock washers

1 Passengers/right side insert plate 8 4mm Flat washers

1 Drivers/left side insert plate 21 8mm x 25mm Hex bolts

1 Back Seat plate 27 8mm Flat washers

1 Bottom cross bar 27 8mm Lock washers

2 Tube Pins with cables 6 Tie Downs brackets

1 Rubber Trim strip 6 8mm Nut Tabs

1 Foam Tape 50mm wide x 6.5mm thick 6 8mm x 35mm Button Head bolts

1 Foam Tape 25mm wide x 3mm thick 2 6mm x 20mm Hex bolts

1 Drivers/left bracket 4 6mm Flat washers

1 Passengers/right rear brackets A & B 2 6mm Lock washers

2 Hex keys (1) 4mm & (1) 8mm 2 6mm Hex Nut

6 8mm x 60mm Button Head bolts

Page 1 of 6

INSTALLATION INSTRUCTIONS

2011-13 JK 4 DR SECURITY CARGO LID PART # ALC25001

Passengers / right

Side Plate

Driver / Left

Side Plate

Back seat

late

Bottom cross tube

Passengers /

ight

Side Insert Plate

Passengers / right

Rear brackets

Driver / Left

Bracket

Driver / Left

Side Insert Plate

Car

o Center section Lid

Tube Pin

Foam ta

e 50mm wide

Foam ta

e 25mm wide

Rubber trim stri

Bracket

8mm Nut tab

Tie

down

bracket

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 2011-13 JK 4 DR SECURITY CARGO LID PART # ALC25001 PARTS LIST: Qty 1 1 1 1 1 1 1 2 1 1 1 1 1 2 6 Description Cargo Center section lid with keys Passengers/right side plate Drivers/left side plate Passengers/right side insert plate Drivers/left side insert plate Back Seat plate Bottom cross bar Tube Pins with cables Rubber Trim strip Foam Tape 50mm wide x 6.
PAGE 2
PROCEDURE: 1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. 2. Start by Referring to owner’s manual for removal of the hard top or soft top pending on which you have. 3.
PAGE 3
11.
PAGE 4
Fig 4A Fig 5 Attached with 8mm hardware Cargo Lid Back seat plate Fig 6 Fig 7 Cargo Lid Attached with 8mm button head bolts& hardware Driver side plate Cargo Lid Back seat plate Attached with 8mm hardware Driver side plate Back seat plate Fig 8 Fig 8A Driver side bracket Locking Latch plate Page 4 of 6
PAGE 5
Fig 8B Fig 9 Passenger side bracket A Attached with 8mm hardware Driver side plate Back seat plate Attached with 8mm hardware Driver side bracket Fig 9A Fig 10 Passenger side bracket B Passenger side shown Passenger side plate Attached with 6mm hardware Attached with 4mm hardware Passenger side bracket A Fig 10A Fig 11 Driver side shown Tap to align Rubber Strip trim as needed Page 5 of 6
PAGE 6
Fig 12 Driver side shown Fig 11A Driver side shown Tap to align Secure roof with 8mm x 60mm Button head bolts Fig 13 Fig 14 Driver side shown Locking Latch plate Tie down shown Make sure to realign Tube Pin placed through hole Tube pin locked Page 6 of 6