Operation Manual

5
GB
How to Start the Appliance
NOTICE
After the appliance has been delivered, stand it in the
upright position and wait approximately 3 hours be-
fore connecting it to the electrical outlet to guarantee
that it operates properly.
Before placing foodstuffs in the refrigerator or freezer, clean
the interior well with warm water and baking soda.
Motor protection delay
This model is provided with a motor protection control
system. Therefore, if the compressor does not start
immediately upon installation, do not worry as it will
start automatically after approximately 8 minutes.
This is also what will happen every time the power
supply is interrupted, both due to a power failure or
should you switch it off yourself (to clean or defrost
your freezer, for example).
After plugging the appliance into a suitable electricity socket,
ensure the display is on with the “OFF” words in the
indication spaces concerning the two compartments (fridge
and freezer).
Freezer compartment
When the appliance is switched on (by pressing the ON/OFF
button “A” for more than two seconds), the freezer
compartment is automatically brought to the standard setting
of - 18°C. We recommend you enable the SUPER FREEZE
function to speed up the cooling process of the compartment;
when the latter has reached its optimal temperature, the
function shall be automatically disabled and you may place
your frozen food inside the compartment.
Refrig ompartment
When the appliance is switched on, the refrigerator
compartment is brought to the standard setting of + 5°C.
We recommend you enable the SUPER COOL function to
speed up the cooling process of the compartment: after a
few hours, you may place food inside the refrigerator.
How to use the display
Firstly, take all the advice that appears in the form of scrolling
text on the display: it will be of use to you, especially when
you make your first settings.
Temperature settings:
If the appliance is switched off, the temperatures set at that
time will appear in the indication spaces on the display
concerning the refrigeration and freezer compartments (G
for the refrigerator and H for the freezer). To change these,
press the MODE (D) button as many times as necessary for
the figure corresponding to the temperature set to flash in
the relative indication space.
Now you can select the new tem-
perature to set by pressing the ADJUST/SELECT + (E) (to increase
the temperature displayed by one degree) and/or ADJUST/
SELECT - (F) (to decrease the temperature displayed by one
degree) buttons. Once you have reached the desired tempera-
ture, you should set it by pressing the MODE (D) button again
to confirm the selection. Now the new temperature will stop
flashing and will remain fixed in the relevant indication space on
the display to indicate that the new setting has been made.
NOTE: if you do not confirm your selection by pressing the
MODE button within ten seconds of the last action
performed on the display, the latter shall go back to displaying
the temperature previously in being and indicate that no
new temperature has been set.
The temperatures set automatically are +5°C for the refrigerator
compartment and -18°C for the freezer compartment and these
are the standard temperatures for food storage.
The settable temperatures for the refrigerator compartment
range from +2°C to +8°C, whereas those for the freezer
compartment range from -18°C to -26°C. When the ECO
function is enabled, the possible settings are instead closer
to the standard ones for food storage: from +4°C to +6°C
for the refrigerator compartment and from -18°C to -20°C
for the freezer compartment. The possible increases and
decrease are still of 1°C.
When the HOLIDAY function is enabled, temperature
regulations cannot be made, but the appliance automatically
sets itself to the best setting for the situation: +12°C for the
refrigerator compartment and -18°C for the freezer
compartment.
How to use the functions:
ECOECO
Function symbol in normal operating conditions
(only green symbol lit)
Function selected (green symbol and red outline
lit)
Function enabled (green symbol and blue
background lit)
To enable and disable the ECO function, just press the ECO
button (B). Press the MODE (D) button as many times as
necessary for the red outline of the function you wish to act
on to light up: this indicates that the function has been
selected and is ready to be enabled or disabled.