Use and Care Guide

-14-
Fly Ash – This accumulates in the horizontal portion of an exhaust run. Though non-combustible, it may impede
the normal exhaust ow. It should therefore be periodically removed.
Inspection and Removal – The chimney connector and chimney should be inspected annually or per ton to
determine if a creosote or y ash build-up has occurred. If creosote has accumulated, it should be removed to
reduce the risk of a chimney re. Inspect the system at the stove connection and at the chimney top. Cooler
surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top as well as
from the bottom. The creosote should be removed with a brush specically designed for the type of chimney
in use. A qualied chimney sweep can perform this service. It is also recommended that before each heating
season the entire system be professionally inspected, cleaned and, if necessary, repaired. To clean the chimney,
disconnect the vent from the stove.
INTERIOR CHAMBERS
Periodically remove and clean the burnpot and the area inside the burnpot housing. In particular it is advisable
to clean out the holes in the burnpot to remove any build up that may prevent air from moving through the burn
pot freely. Remove the two (2) plates on each side of the burnpot housing and clean out the rear chamber. If a
vacuum is used to clean your stove, we suggest using the AV15E AshVac vacuum. The AV15E AshVac is designed
for ash removal. Some regular vacuum cleaner (i.e. shop vacs) may leak ash into the room.
ASH DISPOSAL
Ashes should be placed in a steel container with a tight tting lid and moved outdoors immediately. The closed
container of ashes should be placed on a non-combustible oor or on the ground, well away from combustible
materials, pending nal disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they
should be retained in the closed container until all cinders have thoroughly cooled. Other waste shall not be placed
in this container.
SMOKE AND CO MONITORS
Burning wood naturally produces smoke and carbon monoxide(CO) emissions. CO is a poisonous gas when
exposed to elevated concentrations for extended periods of time. While the modern combustion systems in heaters
drastically reduce the amount of CO emitted out the chimney, exposure to the gases in closed or conned areas
can be dangerous. Make sure you stove gaskets and chimney joints are in good working order and sealing properly
to ensure unintended exposure. It is recommended that you use both smoke and CO monitors in areas having the
potential to generate CO.
CHECK AND CLEAN THE HOPPER
Check the hopper periodically to determine if there is any sawdust or pellets that are sticking to the hopper surface.
Clean as needed.
DOOR AND GLASS GASKETS
Inspect the main door and glass window gaskets periodically. The main door may need to be removed to have
frayed, broken, or compacted gaskets replaced by your authorized dealer. The glass gasket has a gap at the
bottom for the airwash. This unit’s door uses a 5/8” diameter rope gasket.
BLOWER MOTORS
Clean the air holes on the motors of both the exhaust and distribution blowers annually. Remove the exhaust blower
from the exhaust duct and clean out the internal fan blades as part of your fall start-up.
PAINTED SURFACES
Painted surfaces may be wiped down with a damp cloth. If scratches appear, or you wish to renew your paint,
contact your authorized dealer to obtain a can of suitable high-temperature paint.
GLASS - CLEANING, REMOVAL AND REPLACEMENT OF BROKEN DOOR GLASS
Cleaning - We recommend using a high quality glass cleaner. Should a build up of creosote or carbon accumulate,
you may wish to use 000 steel wool and water to clean the glass. DO NOT use abrasive cleaners. DO NOT perform
the cleaning while the glass is HOT. In the event you need to replace the glass, remove the four(4) screws and glass
retainers. While wearing leather gloves (or any other gloves suitable for handling broken glass), carefully remove
any loose pieces of glass from the door frame. Dispose of all broken glass properly. ONLY high temperature ceramic
glass of the correct size and thickness may be used. DO NOT substitute alternative materials for the glass. Contact
your authorized dealer to obtain this glass. Re-install the new glass by re-attaching the retainers and screws, careful
not to overtighten the screws for this could damage the glass. DO NOT abuse the door glass by striking, slamming
or similar trauma. Do not operate the stove with the glass removed, cracked or broken.