DVD-E616P1 DVD-ROM Drive User Manual 1
Copyrights/Disclaimer Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Copyrights/Disclaimer ....................................................... 2 Notices ................................................................................ 4 ASUS Contact Information ................................................ 5 Safety Information ............................................................. 6 Installation Notices ....................................................... 6 Using the Device ..........................................................
Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
ASUS Contact Information ASUSTeK COMPUTER INC. (Asia-Pacific) Address: General Tel: General Fax: General Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support MB/Optical Drives (Tel): +886-2-2890-7121 (English) Notebook (Tel): +886-2-2890-7122 (English) Desktop/Server (Tel): +886-2-2890-7123 (English) Support Fax: +886-2-2890-7698 Web Site: www.asus.com.
Safety Information Observe the following precautions before installing and using the ASUS DVD-E616P1 Installation Notices Do not place this device in an unstable position, or on vibrating surfaces. Do not place this device under direct sunlight or in humid or damp places. Do not use or place this device near magnetic fields, televisions, or radios to avoid electronic interference that affects drive performance. Do not attempt to disassemble or repair the drive.
Safety Information Using the Device • Use of any controls, adjustments, or procedures other than those specified in this manual may result to hazardous radiation exposure. • Do not attempt to disassemble the drive. • Do not move the device from a cold to a warm or hot environment. Drastic change of temperature is harmful to the device. • Before moving or uninstalling the drive, remove disc from it, if any. • Prevent liquids and metal objects to get into the device.
Package Contents Upon opening your ASUS DVD-E616P1 drive package, check if all the following items are present and in good condition. If any of the items is damaged or missing, contact your retailer immediately. • ASUS DVD-E616P1 DVD-ROM Drive • Audio cable • Mounting screw package • DVD-ROM driver disc • User Manual (English) with 12-Language Quick Installation Guide • DVD playback software CD The above items are available in retail boxes only.
Welcome! Thank you for buying the ASUS DVD-E616P1 Drive! To ensure proper installation and use of this device, read the instructions and other important information contained in this manual. Product Introduction Specifications The DVD-E616P1 has the following specifications: • Sustained Transfer Rate DVD 16x max. ~ 21600 KB/sec CD 48x max. ~ 7200 KB/sec • Random Access Time DVD: 90 msec and CD: 85 msec • Interface ATAPI specification • Data Buffer Size 256 KB/s • Application discs 12cm or 8 cm diameter, 1.
Front Panel 1 2 3 4 1. Emergency Eject Pinhole In cases when you cannot eject a disc from the drive using the eject button due to power failure or software problems, insert a pin or a paper clip into this hole to manually eject the tray and the disc. Make sure the power of the drive is turned off and wait more than one minute till the disc rotation is stopped. 2. READ Indicator This LED (Green) is lit on all disc read activity. 3. Disc Loading Tray This tray holds the optical disk media.
Rear Panel 7 8 9 10 7. Audio Output This connector is for an analog audio output cable. This connector is compatible with “Molex 70553”. Pin Name Description 1 L Left channel audio output 2&3 G Ground 4 R Right channel audio output 8. Device Configuration Jumper These pins allow you to select either Master, Slave, or Cable Select mode for the DVD-ROM device. (Refer to page 12 for jumber settings.
Setting the Jumper Terminals Configure the jumpers to set the device to master or slave mode before physically installing it to your computer chassis. Use jumper blocks to short the pins to your desired setting. Make sure to correctly put the jumper blocks over the pins. Failure to do so may cause irreparable damage to the drive! JUMPER TERMINALS Master Mode RESERVED PIN 1 Cover the two pins labeled MA (see illustration) to set the DVD-ROM drive as a secondary master drive.
Installing the DVD-ROM Drive Follow these steps to install the drive into the computer chassis. Refer to your computer manual for specific instructions on opening the chassis and installing drives. 1. Remove the cover of an empty 5.25-inch external drive bay. 2. Carefully insert the DVD-ROM drive into the bay and push it inward until it is flushed to the chassis front panel. The holes on the sides of the drive should align with the holes on the drive bay.
3. Secure the drive with screws that came with the drive package. Use two screws on each side of the drive. Depending on the space on your chassis, you may need to connect the drive cables before securing the drive into the chassis. For cable connections, proceed to the following section, “Connecting the Drive Cables.
Connecting the Drive Cables 1. Connect the power cable plug to the power connector on the rear panel. 2. Connect the 40-pin IDE cable plug to the IDE connector, matching the red pin stripe on the cable with Pin 1 on the connector. 3. If your computer has a sound card or an onboard audio feature, connect an audio interface cable to the 4-pin analog audio connector on the rear of the drive.
DVD-ROM Drive Basics Placing a Disc into the Drive 1. Press the eject button on the front of the drive to eject the tray. 2. When the drive tray ejects out of the drive, place the disc on the tray with the label (printed) side up.
If you are using a 12-cm disc, place it on the tray making sure that it fits the outer circular border. This border helps hold the disc in place. If you are using an 8-cm disc, place it on the inner circular border on the tray. 12-cm Disc 8-cm Disc 3. Press the drive eject button or lightly push the center of the drive tray to replace the tray inside the drive. Ejecting a Disc from the Drive 1. Press the eject button on the front of the drive to eject the tray. 2. Carefully remove the disc from the tray.
Using the Emergency Eject Pinhole The emergency eject pinhole on the front of the drive allows you to manually eject the drive tray and remove a disc from the drive in cases when: • supply of power to the computer is cut due to electrical power outage • the drive malfunctions. Use the manual method only as a last resort when the eject button does not work. Make sure that you have turned off your computer before ejecting the drive tray. Follow these steps to eject the drive tray using the emergency pinhole.
Using Compact Discs Take note of the instructions in this section when using compact discs. These instructions will help you avoid damaging the discs and your DVD-ROM drive. Cleaning a Disc Spray the disc with compressed air for about five seconds to get rid of the dust on a disc. Handling a Disc Hold a disc by the edges. Do not touch the disc surface.
Technical Information Environmental Specifications Temperature Operation: Storage: +5°C to +45°C - 20°C to +60°C Humidity Operation: Storage: 5% to 85% non-condensing 5% to 90% non-condensing Vibration Operation: Storage: 0.25G peak at 10 ~ 300 Hz 1.
DVD Region Codes Region codes are part of the DVD standard. However, Region code on DVD discs are optional. DVD discs with no specified region code can be played on all DVD players. The world is set up into regions according to DVD titles. There are six regions around the world as illustrated by the map below. This DVD drive can be changed to play a DVD from any region in the world but can ONLY be changed five times.
ASUS DVD-E616P1 User Manual
DVD-E616P1 DVD-ROM Drive Quick Installation Guide In 12 Languages 23
Quick Installation Guide English Hardware Installation 1. Turn off your computer and any peripheral devices connected to it. 2. Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling the device to avoid damaging it due to static electricity. 3. Remove the computer cover. 4. Configure the DVD-ROM drive jumpers to set the device to master or slave mode before installing it into the chassis.
Guide d’Installation Rapide Installation Matérielle 1. Eteignez votre ordinateur et tous les périphériques connectés. 2. Utilisez un bracelet anti-statique relié à la terre ou touchez un objet relié à la masse ou un objet métallique, tel le boîtier d’alimentation, avant de manipuler l’équipement pour éviter de l’endommager à cause de l’électricité statique. Français 3. Enlevez le couvercle de l’ordinateur. 4.
Schnellinstallationsanleitung Hardwareinstallation 1. Schalten Sie Ihren Computer und alle angeschlossenen Peripheriegeräte aus. 2. Um Schäden durch statische Elektrizität zu vermeiden, tragen Sie bitte eine geerdete Manschette oder berühren Sie einen richtig geerdeten Gegenstand oder Metallgegenstand wie z.B. das Netzteilgehäuse, bevor Sie das Gerät in die Hand nehmen. 3. Entfernen Sie die Abdeckung des Computers. Deutsch 4.
Guida all’installazione rapida Installazione dell'hardware 1. Spegnere il computer e tutte le periferiche ad esso collegate. 2. Prima di maneggiare il dispositivo provocando danni causati dall'energia statica, indossare una fascetta antistatica, oppure toccare un oggetto protetto con massa a terra, o un oggetto metallico come la scatola d'alimentazione. 3. Rimuovere la copertura del computer. 4.
Guía de instalación rápida Instalación del hardware 1. Apague su equipo y cualquier dispositivo periférico que se encuentre conectado al mismo. 2. Utilice una muñequera de toma de tierra o toque un objeto a tierra seguro o un objeto de metal, como por ejemplo la carcasa de la fuente de alimentación, antes de manipular el dispositivo para evitar dañarlo debido a la electricidad estática. 3. Retire la cubierta del equipo. 4.
® 31
Snelle installatiegids Hardware-installatie 1. Zet de computer uit en maak alle verbindingen los. 2. Gebruik een geaard polsbandje of raak een goed geaard voorwerp aan, zoals een radiator, voordat u de onderdelen hanteert. U zou anders schade kunnen veroorzaken door statische elektriciteit. 3. Open de behuizing van de computer. 4. Configureer de dvd-lezer door hem met jumpers in te stellen als master of slave, voordat u hem in de computer monteert. Met jumpertjes kunt u de juiste instellingen maken.
нст укция по монтажу онтаж п ивода DVD-дисков 1 . Отключите питание компьюте а и пе ифе ийных уст ойств. всех подключенных к компьюте у 2 . о избежание пов еждения уст ойств статическим элект ичеством п и установке компьюте ного обо удования используйте заземляющий б аслет или п икоснитесь к заземленному обо удованию или металлическому п едмету (нап име , ко пус блока питания) п ежде чем взять в уки обо удование, чувствительное к статическому элект ичеству. 3 . 'нимите кожух с ко пуса компьюте а.
Snabbinstallationsguide Installation av maskinvara 1. Stäng av datorn och all ansluten kringutrustning. 2. Använd en jordad handledsrem eller rör vid ett säkert jordat föremål eller ett metallföremål som t ex strömkällans hölje, innan du hanterar enheten för att inte skada den med statisk elektricitet. 3. Ta bort datorns kåpa. 4. Konfigurera DVD-ROM-enhetens byglar för att försätta enheten i master(primärt) eller slavläge (sekundärt ) innan den monteras i datorn.
Hýzlý Kurulum Kýlavuzu Donaným Kurulumu 1. Bilgisayarýnýz ve baðlý tüm çevresel aygýtlarý kapatýnýz. 2. Vücudunuzdaki statik elektriðin donanýma zarar vermemesi için aygýt üzerinde herhangi bir iþlem yapmadan önce topraklamalý bileklik kullanýn veya düzgün bir þekilde topraklanmýþ güç kaynaðý muhafazasý gibi metal bir nesneye dokunun. 3. Bilgisayar kapaðýný açýn. 4. Kasaya takmadan önce DVD-ROM sürücü jumperlarýný aygýtý master veya slave modlarýný getirmek için yapýlandýrýn.
