User's Manual
Table Of Contents
- 目錄內容
- 第一章:產品介紹
- 第二章:硬體裝置資訊
- 第三章:開啟電源
- 第四章:BIOS 程式設定
- 4.1 管理、更新您的 BIOS 程式
- 4.2 BIOS 程式設定
- 4.3 主選單(Main)
- 4.4 進階選單(Advanced)
- 4.4.1 處理器設定(CPU Configuration)
- 4.4.2 晶片組設定(Chipset)
- 4.4.3 Legacy 裝置設定(Legacy Device Configuration)
- 4.4.4 USB 裝置設定(USB Configuration)
- 4.4.5 PCI 隨插即用裝置設定(PCI PnP Settings)
- 4.4.6 電源設定(Power On Configuration)
- 4.4.7 事件記錄設定(Event Log Configuration)
- 4.4.8 系統監控功能(Hardware Monitor)
- 4.4.9 PCI Express 設定(PCI Express Configuration)
- 4.4.10 ACPI 設定(ACPI Configuration)
- 4.5 伺服器選單(Server)
- 4.6 啟動選單(Boot)
- 4.7 離開 BIOS 程式(Exit)
- 第五章:RAID 磁碟陣列設定
- 第六章:安裝驅動程式
- 附錄:相關資訊
華碩 Z8NA-D6 系列主機板使用手冊
6-9
6.1.3 Red Hat
®
Enterprise Linux 作業系統
請依以下的步驟,在 Red Hat
®
Enterprise 作業系統安裝過程中安裝 RAID
驅動程式:
1. 使用 Red Hat
®
作業系統安裝光碟片啟動系統。
2. 然後於 Boot: 後,輸入 linux dd,然後按下 <Enter> 鍵。
注意:當在 RHEL AS5 作業系統安裝過程中安裝 RAID 驅動程式
時,輸入 linux dd noprobe=ata1 noprobe=ata2 ...,ata 數取決於用
在建立 RAID 磁碟陣列的硬碟數量。例如,若您想使用六個硬碟
來建立 RAID 陣列,請輸入以下指令列:linux dd noprobe=ata1
no p robe=at a2 no p robe=a ta3 no probe=a ta4 no prob e=ata5
noprobe=ata6
-Toinstallorupgradeingraphicalmode,pressthe<ENTER>key.
-Toinstallorupgradeintextmode,type:linuxtext<ENTER>.
-Usethefunctionkeyslistedbelowformoreinformation.
[F1-Main] [F2-Options] [F3-General] [F4-Kernel] [F5-Rescue]
boot:linuxddnoprobe=ata1noprobe=ata2
4. 當詢問您來源的驅動程式磁片安裝位置時,請按 <Tab> 鍵選擇 fd0。接
著再按 <Tab> 鍵來移至 OK 處,然後按下 <Enter> 鍵。
3. 當系統詢問您是否
具備驅動程式磁片時,請按下 <Tab> 鍵來選擇 Yes,
然後按下 <Enter> 鍵繼續。
Main Menu
Doyouhaveadriverdisk?
Yes No
DriverDiskSource
You have multiple devices which could serve
assourcesfor a driverdisk. Which wouldyou
liketouse?
OK
Cancel
fd0
scd0