User's Manual
Table Of Contents
- 目錄內容
- 第一章:產品介紹
- 第二章:硬體裝置資訊
- 第三章:開啟電源
- 第四章:BIOS 程式設定
- 4.1 管理、更新您的 BIOS 程式
- 4.2 BIOS 程式設定
- 4.3 主選單(Main)
- 4.4 進階選單(Advanced)
- 4.4.1 處理器設定(CPU Configuration)
- 4.4.2 晶片組設定(Chipset)
- 4.4.3 Legacy 裝置設定(Legacy Device Configuration)
- 4.4.4 USB 裝置設定(USB Configuration)
- 4.4.5 PCI 隨插即用裝置設定(PCI PnP Settings)
- 4.4.6 電源設定(Power On Configuration)
- 4.4.7 事件記錄設定(Event Log Configuration)
- 4.4.8 系統監控功能(Hardware Monitor)
- 4.4.9 PCI Express 設定(PCI Express Configuration)
- 4.4.10 ACPI 設定(ACPI Configuration)
- 4.5 伺服器選單(Server)
- 4.6 啟動選單(Boot)
- 4.7 離開 BIOS 程式(Exit)
- 第五章:RAID 磁碟陣列設定
- 第六章:安裝驅動程式
- 附錄:相關資訊
華碩 Z8NA-D6 系列主機板使用手冊
4-37
4.6.2 啟動選項設定(Boot Settings Configuration)
Quick Boot [Enabled]
本項目可讓您決定是否要跳過PO S T的一些功能。開啟本項目將可加速
開機的時間。當設定為 [Disabled] 時,BIOS 程式會運作所有的自我測試功
能。設定值有:[Disabled] [Enabled]
Full Screen Logo [Enabled]
若您要使用全屏開機畫面,請將本項目設定為啟用 [Enable]。設定值有:
[Disabled] [Enabled]
如果您欲使用華碩 MyLogo2™ 功能,請務必將 Full Screen Logo
項目設定為 [Enabled]。
v02.61 (C)Copyright 1985-2008, American Megatrends, Inc.
BIOS SETUP UTILITY
Boot
BootSettingsConguration
QuickBoot [Enabled]
Full Screen Logo [Enabled]
AddOn ROM Display Mode [Force BIOS]
BootupNum-Lock [On]
Wait For ‘F1‘ If Error [Enabled]
Hit ‘DEL‘ Message Display [Enabled]
Interrupt 19 Capture [Enabled]
←→ Select Screen
↑↓ Select Item
+- Change Option
F1 General Help
F10SaveandExit
ESCExit
AllowsBIOStoskip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
AddOn ROM Display Mode [Force BIOS]
本項目讓您設定擴充裝置韌體程式的顯示模式。設定值有:[Force BIOS]
[Keep Current]
Bootup Num-Lock [On]
本項目讓您設定在開機時 NumLock 鍵是否自動啟動。設定值有:[Off] [On]
Wait For‘F1’If Error [Enabled]
當您將本項目設為 [Enabled],那麼系統在開機過程出現錯誤訊息時,將
會等待您按下 <F1> 鍵確認才會繼續進行開機程式。設定值有;[Disabled]
[Enabled]
Hit‘DEL’Message Display [Enabled]
當您將本項目設為 [Enabled] 時,系統在開機過程中會出現 Press DEL to
run Setup 訊息。設定值有:[Disabled] [Enabled]