Operation Manual

11
R
R
e
e
s
s
i
i
d
d
u
u
a
a
l
l
r
r
i
i
s
s
k
k
s
s
Even if used properly, residual risks can exist even if
the relevant safety regulations are complied with due to the
design determined by the intended purpose.
Residual risks can be minimised if the “Safety information”
and the “Intended usage” as well as the whole of the
operating instructions are observed.
Observing these instructions, and taking proper care, will
reduce the risk of personal injury or damage to the
equipment.
 Failure to observe the safety precautions can lead to injury
to the operator or damage to property.
 Risk from electricity, by using non-standard electrical
connections.
 Touching live parts of opened electrical components.
In addition, in spite of all the precautionary measures taken,
non-obvious residual risks can still exist.
S
S
a
a
f
f
e
e
w
w
o
o
r
r
k
k
i
i
n
n
g
g
Before commissioning this product, read and keep to
the following advice. Also observe the preventive
regulations of your professional association and the safety
provisions applicable in the respective country, in order to
protect yourself and others from possible injury.
L
Pass the safety instructions on to all persons who work
with the machine.
L
Keep these safety instructions in a safe place.
 Make yourself familiar with the equipment before using it,
by reading and understanding the operating instructions.
 Do not use the machine for unsuitable purposes (see
“Normal intended use” and “Working with the vacuum
cleaner”).
 Ensure that you have stand in a secure standing
position and maintain your balance at all times. Do not
bend forwards.
 Pay attention at all times. Take care with what you are
doing, and approach the work sensibly. Do not use the
machine:
− when you are tired.
− under the influence of drugs, alcohol or medications
that may impair your powers of judgement.
 When working with the machine, always wear
− protective goggles or face mask
− safety gloves
− hearing protection
− slip-proof shoes
− long trousers
 Wear suitable work clothing:
− do not wear any loose-fitting clothing or jewellery,
since these may be caught or trapped by moving parts
 Within his area of work the operator is responsible for
third parties.
 Children and youngsters less than 16 years of age and
people who have not read the operating manual must not
operate the machine.
 Keep children away form machine.
 Never operate the machine if other persons are in the
immediate vicinity.
 The user is responsible for accidents with other people or
their property.
 Never leave the saw unattended.
 Keep your workplace in an orderly condition!
Untidiness can result in accidents.
 Do not overload the machine! You work better and safer in
the given performance range.
 Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on
the machine that could impair the safety.
 Faulty or damaged parts in the device must be replaced
immediately.
 Do not spray machine with water
(this is hazardous due to live components).
 Do not leave the machine standing in the rain or use
when raining.
 Store the unused machine in a dry locked place away
from the reach of children.
 Switch the machine off and remove the mains plug from
the socket when
− carrying out repair works
− carrying out servicing and repair works, removal of
faults
−
checking the leads to see whether these
are caught up or damaged
−
changing over from vacuuming to blowing
− transporting
− leaving unattended (even during short
interruptions)
−
unusual noises and vibrations
 Check the machine for possible damage
−
Before continuing to use the machine, the protective
devices must be inspected to ensure that they work
perfectly and with their intended function
−
Check whether the parts are damaged. All parts must
be correctly installed and fulfil all conditions to ensure
perfect operation of the saw
−
Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
−
Damaged or illegible safety warning labels should be
replaced immediately.
Electrical safety
 Design of the connection cable according to IEC 60245
(H 07 RN-F) with a core cross-profile section of at least
−
3 x 1.5 mm
2
for cable lengths up to 25m
−
3 x 2.5 mm
2
for cable lengths over 25m