Diane Ceiling Mounted Oscillating Directional Fan READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz Please do not use any electric or battery powered tools in the assembly and installation of this or any Matthews Fan Company product.
TOOLS AND MATERIALS REQUIRED Philips screw driver Standard, flat-head screw driver 11 mm wrench Step ladder Wire cutters PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: a a. b. c. d. Hanger bracket assembly Ball / down rod assembly Fan motor assembly Metal blade with cage (decorative* or safety**) or Wood blade e. Receiver with 6 wire nuts f. Transmitter+holder+2 mounting screws g. Allen wrench h.
READ AND SAVE THESE SAFETY AND INSTALLATION INSTRUCTIONS. Consult a licensed electrician if unsure of any point below mentioned. DANGER/WARNING/CAUTION 1. High voltage and moving parts around motors and motor driven equipment can cause serious or fatal injuries. Always disconnect power source at main switch before wiring, servicing or cleaning unit. Do not rely on fan control device to prevent unexpected start-up or electrical shock.
11. To reduce the risk of personal injury, install the supplementary mounting means and use only the hardware provided with the fan. 12. Warning: TO REDUCE THE RISKS OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. B.
MOUNTING/INSTALLATION OF THE FAN Ceiling hanger bracket Before touching a screw driver thoroughly read these instructions. Ceiling canopy Warning/Caution: Before installing fan, turn off power at service panel and check all visible screws and bolts for tightness. Canopy cover Figure 5 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise. (Fig. 5) Electrical box 2.
5 C. Wooden Blade Head: If your fan is one with wooden blade head, attach your blades as the last step in the assembly process. Do not attach them now. Attach them in step No.: 9. Handle your blade head carefully otherwise you will bend the blade irons and cause your fan to vibrate when in use. Registration slot 6. Loosen the two set screws from the top coupling of the motor assembly. (Fig. 8) Figure 9 7. Carefully feed the fan wires up through the down rod.
2. Motor to Receiver Electrical Connections: OUTLET BOX A. Connect the WHITE wire from the fan to the WHITE wire marked "TO MOTOR N" from the Receiver. BLACK (HOT) BLACK ("AC IN L") B. Connect the BLACK wire from the fan to the BLACK wire marked "TO MOTOR L" from the Receiver. WHITE (NEUTRAL) GREEN OR BARE COPPER (GROUND) WHITE ("AC IN N") RECEIVER BLACK ("TO MOTOR L") C. Connect the BLUE wire from the fan to the BLUE wire marked "oscillation" from the Receiver.
OPERATING THE REMOTE CONTROL Install 12V MN21/A23 battery (included). To prevent damage to transmitter, remove the battery if not used for long periods. (Fig. 14) Restore Power to Ceiling Fan. A. H, M, L Buttons: These buttons are used to set the fan speeds as follows; L: Low Speed M: Medium Speed H: High Speed Figure 14 B. OFF Button: This button turns the fan off. C. ACCESSORY Button: This button is used to control the oscillating operation.
CARE OF AND TROUBLESHOOTING YOUR FAN 1. Check hardware bi-yearly. Because of the fan's natural movement some connections may become loose over time. Check the support connections, brackets and blade attachments twice a year. Make sure they are secure. It is not necessary to remove fan from the wall. 2. Clean your fan periodically. This will help to help maintain its new appearance over the years. Use only a lightly water-moistened, lint free cloth to avoid scratching the finish.
LIMITED LIFETIME WARRANTY MATTHEWS-GERBAR, LTD. DBA MATTHEWS FAN COMPANY LIFETIME LIMITED WARRANTY. Ceiling fans are warranted by Matthews-Gerbar, Ltd. to the original user against defects in workmanship or materials under normal use and inside installation for: Motors: Lifetime of original purchaser: Labor & Component parts: (lights, finish, blades, etc…): one year after date of purchase, Light Bulbs: no warranty. Any part, which is determined by Matthews-Gerbar, Ltd.
