Atlona UK HDBaseT Wall Plate Receivers AT-HDWP-UK, AT-HDWP-IR-UK AT-HDWP-UK AT-HDWP-IR-UK User Manual atlona.
Table of Contents 1. Introduction ................................................................................... 3 2. Package Contents ................................................................................... 3 3. Features ................................................................................... 3 4. Panel Descriptions ................................................................................... 4 5. Electrical Box ..............................................
Introduction Extend uninterrupted 1080p signal up to 230ft (70m) with the Atlona UK HDBaseT Wall Plate Receivers. With pass through support of 4Kx2K, 1920x1200, lossy & lossless audio, and bi-directional IR* signals over a single category cable, the HD extenders provide affordable, high quality, solutions for your audio/video and IR* control needs.
Panel Description 1 IR IR IN 2 - 3 + IR OUT HDMI OUT PWR LINK FW AT-HDWP-IR-UK 4 5 6 1. IR IN Port: Connect the IR receiver to this port.* 2. IR OUT Port: Connect the IR Emitter to this port.* 3. HDMI OUT Port: Connect to HDMI display. 4. Yellow Link LED: Signal Indicator for the CAT5e/6/7 OUT port. LED will remain solid, unless there is an issue with the cable or signal, then it will blink. Green Power LED: Power indicator. If plugged in light will remain solid.
Wall Plate Installation A B C There are four pieces that will need to be interconnected in order for the AT-HDWP-IR-UK to be installed in the wall. The electrical box (picture A), the HDBaseT module (picture B), the face plate (picture C) and the CAT cable. First, remove the face plate from the HDBaseT module. To do this, remove the four 4mm screws on the sides (as pictured above).
Install the wall plate back box to the electrical box, use the two supplied 30mm screws. Thread the screws through the HDBaseT module into the electrical box (as seen above). Note: Do not overtighten the screw or the HDBaseT module may warp. Once a small amount of resistance is felt stop tightening. Replace the four 4mm screws (as seen above). Note: If the four holes on the face plate do not line up with the back box, loosen the 30mm screws on the HDBaseT module. atlona.
Captive Screw IR captive screw connector is an added feature on the HDWP-IR-UK. The Captive screw connector allows you to cut cables down to a suitable length, reducing cable clutter and providing a more reliable connection. Connecting When connecting the cables to the female captive screw connector it is important that the wires be terminated correctly. The female captive screw connector (see picture A) has a contact plate at the top and must have the wires touching it for signal to pass.
HDWP Connection HDMI HDBaseT Blu-ray Player AT-HDTX FIRMWARE POWER HDMI IN Display 1 LINK HDMI OUT PWR LINK CAT5e/6/7 OUT FW AT-HDTX AT-HDWP-UK AT-HDWP-UK HDMI HDBaseT POWER SYNC LOCK B M AUTO 1 2 3 4 1 INT LEARN 2 Blu-ray Player INPUT AT-HDCAT-4 AUTO EDID AT-HDCAT-4 FIRMWARE HDMI 1 HDMI 2 INPUT ANALOG - + + - L R SPDIF HDMI 1 OUTPUT 2 3 4 BACK UP MAIN DC 24V DC 24V AT-HDCAT-4 HDMI OUT PWR LINK FW AT-HDWP-UK AT-HDWP-UK Display 1 atlona.
HDWP-IR Connection HDMI HDBaseT Control 1 12V DC FACTORY RESTORE ID 1 3 5 2 4 6 COMPONENT HDMI WIFI 1 DIGITAL COAX OUT eSATA USB ETHERNET 2 3 4 NO NC COM NO NC COM NO NC COM NO NC COM ZIGBEE L SERIAL 1 VIDEO OUT SERIAL 2 ENTER IR IN MATRIX IN 1 RS-232 MATRIX OUT AUDIO IN 1 3rd Party Control Box AT-PRO3HD44M LAN AUDIO OUT 3 2 4 COAX IR OUT OUT HDMI IN CAT5e/6/7 COAX IR OUT OUT CAT5e/6/7 ZONE 2 ZONE 1 POWER FUNCTION CANCEL DEFAULT 2 3 4 ALL MEMORY EDID IR
HDWP-IR Connection cont. HDMI HDBaseT Control IR Emitter Blu-ray Player AT-HDTX-IR POWER IR IN IR OUT FIRMWARE - + PWR IR LINK HDMI IN - + CAT5e/6/7 OUT DC 24V AT-HDTX-IR IR IR IN - + IR OUT HDMI OUT PWR LINK FW AT-HDWP-IR-UK IR Receiver AT-HDWP-IR-UK Display 1 atlona.
Specifications Bandwidth Ports A/V input A/V output IR input IR output Firmware update Power Consumption Audio Resolution Distance 10.2Gbps AT-HDWP-UK 1 x RJ45 1 x HDMI 1 x Mini USB 8.
Safety Information Safeguards To reduce the risk of electric shock, do not expose this product to rain or moisture Do not modify the wall plug. Doing so will void the warranty and safety features. If the wall plug does not fit into your local power socket, hire an electrician to replace your obsolete socket. This equipment should be installed near the socket outlet and the device should be easily accessible in the case it requires disconnection.
Atlona, Inc. (“Atlona”) Limited Product Warranty Policy Coverage Atlona warrants its products will substantially perform to their published specifications and will be free from defects in materials and workmanship under normal use, conditions and service.
Disclaimers This Limited Product Warranty does not imply that the electronic components contained within Atlona’s products will not become obsolete nor does it imply Atlona products or their electronic components will remain compatible with any other current product, technology or any future products or technologies in which Atlona’s products may be used in conjunction with.