User Manual

Industrial DIN-Rail Unmanaged
Gigabit Ethernet Switch
8-port Industrial Unmanaged Gigabit Ethernet Switch
Hardware Installation Guide
Version 1.1
Updated on March, 2011
Introduction
Thank you for purchasing Atop EHG2308 Industrial Unmanaged Gigabit
Ethernet Switch. This document intends to provide customers with brief
descriptions about the product and to assist our customers to get started
using our devices.
Hardware Installation
Step1: Installation on “Din-Rail”
■
EHG2308 switch is equipped with a Din-Rail bracket attached onto
the rear panel. Please follow the below steps to fasten the switch
to the Din-Rail correctly.
■
Tip the switch forward and press it against the Din-Rail after align
the bracket springs to the Din-Rail.
■
Press the bracket against the upper ledge of the Din-Rail until it
clicks.
Step3: Connecting the Network Devices
■
Connect your devices using standard UTP/STP cable with RJ-45
connectors to the switch. (For the cable wiring diagrams, please
refer to the Pin Assignment)
■
The corresponding RJ-45 LED will be lighted if the Ethernet
connection is linked successfully.
■
The LED will be blinked during data transfer by the switch.
※UL Notice for Power supplier
All the series of products are intended to be supplied by a Listed
Power Unit marked with “LPS”, “Limited Power Source” or “Class 2”
with output rate 9-48VDC, 0.45A maximum.
Or, use the recommended power supplies in “Optional Accessories”.
Inside the Package
- Main Product
■
One EHG2308 device
- Standard Accessories
■
Terminal block for power input
■
The hardcopy of Hardware Installation Guide
- Optional Accessories
■
US315-12(US), AC100V~240V 50/60HZ 12V/1.25A, US Plug (optional),
→ Atop PN:50500151120009G
■
US315-12(EU), AC100V~240V 50/60HZ 12V/1.25A, EU Plug (optional),
→ Atop PN:50500151120019G
■
Wall mount kit, 45.4*22.8mm(thick:1.5mm), Black color (optional),
→ Atop PN:201GW51CW37004G
Product Description
EHG2308
8-Port Industrial Unmanaged Gigabit Ethernet Switch
■
8 ports of 10/100/1000Base-TX with RJ45 connector
■
5 pins Terminal Block type of the power connector
■
2 LEDs with Power1(P1) and Power2(P2) status
Notice :
The switches are designed to be mounted on a well-grounded place,
such as a metal panel.
Step2: Connecting the Power
■
Prepare the suitable power source and connect it into the switch by
Terminal Blocks (TB5).
■
DC 9-48V for EHG2308.
■
You can connect two DC inputs into the switch power if auto-backup
is needed.
■
Check P1/P2 power LED. The LED(s) will be lighted when the device
is ready.
V+
P2 P1
V- V+ V- F.G.
5-pin Terminal Block for Power Input
Pin
Signal
V+ V- F.G.
DC9-48V 0V Frame Ground
Warning:
Before connecting the switch to the DC power input, please make sure
the DC voltage supplied by the power source is correct and stable.
Technologies
Tel: [phone]
Fax: [phone]
www.atop.com.tw
LED Indicators
There are some LED indicators located at the front panel of the switch.
Name
P1/P2
RJ-45
LED
Green
Green
Yellow
Status
Off
On
Off
Blink
Off
On
Power input 1/2 is not plugged yet
Power status is ready
Link is broken, or no cable is plugged in
The device is transferring data through the port
The link is operated at rate of 10/100 Mbps
The link is operated at rate of 1000 Mbps
Description
EHG2308
Atop Technologies, Inc.
90.6mm
45.4mm
87
65
43
21
V+
P2
P2
P1
P1
V- V+ V- F.G.