BARANSU ! MONO POWER AMPLIFIERS ! OWNER’S INFORMATION ! !
CONTENTS ! 1) IMPORTANT SAFETY INFORMATION 2) CE DECLARATION OF CONFORMITY DISPOSAL POWER REQUIREMENTS 3) INTRODUCTION 4) OVERVIEW UNPACKING AND INSTALLATION 5) VALVE INSTALLATION 6) CONNECTION 7) OPERATION 8) TECHNICAL SPECIFICATIONS 9) WARRANTY INFORMATION 10) CONTACT INFORMATION
! IMPORTANT SAFETY INFORMATION ! RISK OF SHOCK OR ELECTROCUTION! INTERNAL OPERATING VOLTAGES ARE LETHAL! Do not remove top cover, unless specifically instructed to do so in the user manual. This unit contains fuses and other safety components in accordance with BS60065 requirements. In the event of failure, replacement fuse or safety component must be of the same part type and value. ! SUCH REPLACEMENT MUST ONLY BE CARRIED OUT BY A QUALIFIED SERVICE TECHNICIAN.
CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: BS EN 60065 in accordance with the regulations 73/23/EEC, 89/336/EEC (from 1 January 1997) CE 94 Peter Qvortrup, Director Audio Note (UK) Limited 25 Montefiore Road Hove East Sussex BN3 1RD United Kingdom Tel: Fax: +44 (0)1273 220 511 +44 (0)1273 731 498 ! DISPOSAL This product must not be disposed of as normal household waste.
INTRODUCTION Thank you for purchasing this Audio Note (UK) product. With the correct care it should give you many years of pleasure and enjoyment. Please take the time to read all of the information in this manual before connecting your new component to an electrical supply or your system, to ensure both your safety and satisfaction. Please note that due to our desire to continually improve products, specifications are subject to change without notice.
BARANSU MONO POWER AMPLIFIERS Congratulations on your purchase of the Audio Note (UK) BARANSU mono power amplifiers. They are Pure Class A Singled Ended valve amplifiers, equipped with the highly regarded 300B triode valve, producing a level of performance that is radically superior to the vast majority of current designs.
UNPACKING AND INSTALLATION Please take care when unpacking your BARANSU amplifiers. Choose a clean, clear location to unpack them, and be aware that the amplifiers are very heavy; before attempting to unpack or lift the units, check the weight and if necessary use more than one person so that they can be moved safely and easily. We recommend that you retain and carefully store all of the original packing materials, in case transportation / shipping is required at a later date.
VALVE INSTALLATION The amplifiers are shipped without their valve compliment installed. It is necessary to install the valves before operation. It is essential that the valves are installed correctly or serious damage that is not covered by the warranty will result. We recommend that your dealer perform this procedure for you if you are in any way unsure. FIRSTLY, ENSURE THAT THE AMPLIFIERS ARE NOT CONNECTED TO A MAINS ELECTRICAL SUPPLY, AND THAT THE POWER CORDS ARE NOT CONNECTED TO THE AMPLIFIER.
CONNECTION Line inputs Being mono power amplifiers, each BARANSU is fitted with one single ended / RCA input. Looking from behind the amplifiers, they are located at the right hand side of the rear panels. Connect the outputs from your preamplifier to these inputs. Speakers Each amplifier is equipped with 3 colour coded binding posts for connection to your speakers.
OPERATION Once all the connections are completed and checked, ensure that the volume control of your preamplifier / source is at the minimum setting. Turn on all components in the signal chain BEFORE the BARANSU; they should always be the LAST components to be switched ON, and the FIRST to be switched OFF. Turn on the amplifiers by using the rocker switch located on the rear top left of the back panels, just above mains inlet socket.
TECHNICAL SPECIFICATIONS INPUT IMPEDANCE 100k ohm, line level INPUT SENSITIVITY 450mV for full output MAXIMUM OUTPUT 8 watts RMS per channel into 4 or 8 Ohm loads CHANNEL BALANCE +/- 0.3dB VALVE COMPLIMENT 2 x 5R4GY 2 x 300B 2 x 5692 UNIT WEIGHT 27.5KG per amplifier SHIPPING WEIGHT (ORIGINAL PACKAGING) 65KG UNIT DIMENSIONS 220mm (h) x 460mm (w) x 530mm (d) SHIPPING DIMENSIONS (ORIGINAL PACKAGING) 600mm (h) x 650mm (w) x 670mm (d) MAINS INPUT AC 100-120V/220-240V 50/60 Hz MAINS FUSE 3.
WARRANTY INFORMATION Audio Note (UK) warrants this product to be free from defects in materials and workmanship for two years from the original date of purchase from an appointed Audio Note (UK) dealer, and agrees to cover the cost of parts and associated labour required to correct such defects, subject to terms & conditions. This Warranty is offered to the first purchaser only. Any valves supplied with the unit are warranted for three months from the original date of purchase.
CONTACT INFORMATION If in the future your Audio Note (UK) product requires servicing, or if you require technical support or have any questions regarding this or any of our other products, please contact your local Audio Note (UK) dealer. Alternatively, please feel free to contact us directly: -! Audio Note (UK) Limited 25 Montefiore Road Hove East Sussex BN3 1RD United Kingdom Tel: +44 (0)1273 220 511 Fax: +44 (0)1273 731 498 e-mail: info@audionote.co.