User`s manual

Mediant 1000
H.323 User's Manual 238 Document #: LTRT-83401
Table 6-9: Analog Telephony Parameters (continues on pages 236 to 239)
ini File Field Name
Web Parameter Name
Valid Range and Description
MWIDisplay
For a description of this parameter, refer to Table 5-8 on page 86.
StutterToneDuration
For a description of this parameter, refer to Table 5-8 on page 86.
PayPhoneMeteringMode
For a description of this parameter, refer to Table 5-9 on page 89.
MeteringType
For a description of this parameter, refer to Table
5-9 on page 89.
KeyCFUnCond
For a description of this parameter, refer to Table 5-10 on page 91.
KeyCFNoAnswer
For a description of this parameter, refer to Table 5-10 on page 91.
KeyCFBusy
For a description of this parameter, refer to Table 5-10 on page 91
KeyCFBusyOrNoAnswer
For a description of this parameter, refer to Table 5-10 on page 91.
KeyCFDoNotDisturb
For a description of this parameter, refer to Table
5-10 on page 91
KeyCFDeact
For a description of this parameter, refer to Table
5-10 on page 91.
KeyCLIR
For a description of this parameter, refer to Table
5-10 on page 91.
KeyCLIRDeact
For a description of this parameter, refer to Table 5-10 on page 91.
KeyHotLine
For a description of this parameter, refer to Table 5-10 on page 91.
KeyHotLineDeact
For a description of this parameter, refer to Table 5-10 on page 91.
IsTwoStageDial
For a description of this parameter, refer to Table 5-18 on page 119.
IsWaitForDialTone
For a description of this parameter, refer to Table 5-18 on page 119.
WaitForDialTime
For a description of this parameter, refer to Table 5-18 on page 119.
FXOBetweenRingTime
For a description of this parameter, refer to Table 5-18 on page 119.
RingsBeforeCallerID
For a description of this parameter, refer to Table 5-18 on page 119.
DisconnectOnDialTone
For a description of this parameter, refer to Table 5-18 on page 119.
GuardTimeBetweenCalls
For a description of this parameter, refer to Table 5-18 on page 119.
NTTDIDSignallingForm
Determines the type of Direct Inward Dialing (DID) signaling support for NTT
(Japan) modem: DTMF- or Frequency Shift Keying (FSK)-based signaling.
Gateways can be connected to Japan’s NTT PBX using ‘Modem’ DID lines.
These DID lines are used to deliver a called number to the PBX.
Valid options include:
0 = FSK-based signaling (default)
1 = DTMF-based signaling
Note: Applicable only to FXS modules.
EnableDID
Enables Japan NTT ‘Modem’ Direct Inward Dialing (DID) support. FXS modules
can be connected to Japan’s NTT PBX using ‘Modem’ DID lines. These DID lines
are used to deliver a called number to the PBX (applicable to FXS modules). The
DID signal can be sent alone or combined with an NTT Caller ID signal.
EnableDID_X
Enables generation of Japan NTT Modem DID signal per port.
EnableDID_<Port> = <Modem DID>
Modem DID:
0 = Disabled (default).
1 = Enabled.
If not configured, use the global parameter ‘EnableDID’.
Note: Applicable only to FXS modules.
EnableCallerIDTypeTwo
Disables the generation of Caller ID type 2 when the phone is offhooked.
0 = Caller ID type 2 isn’t played.
1 = Caller ID type 2 is played (default).