2015 SUPER DUTY Owner’s Manual 2015 SUPER DUTY Owner’s Manual fordowner.com ford.ca January 2014 First Printing Owner’s Manual Super Duty Litho in U.S.A.
The information contained in this publication was correct at the time of going to print. In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted. © Ford Motor Company 2014 All rights reserved.
Table of Contents Introduction Keys and Remote Controls About This Manual...........................................7 Symbols Glossary.............................................7 Data Recording..................................................9 California Proposition 65..............................11 Perchlorate.........................................................11 Ford Credit..........................................................11 Replacement Parts Recommendation..............................
Table of Contents Memory Function...........................................113 Rear Seats........................................................114 Heated Seats..................................................116 Climate Controlled Seats...........................118 Front Seat Armrest.......................................119 Rear Seat Armrest........................................120 Lighting Lighting Control..............................................65 Autolamps...................................
Table of Contents Rear Axle Towing Limited Slip Differential.............................160 Electronic Locking Differential................160 Towing a Trailer.............................................189 Trailer Sway Control....................................190 Recommended Towing Weights............190 Essential Towing Checks...........................193 Towing Points...............................................205 Transporting the Vehicle..........................
Table of Contents Changing a Fuse............................................231 Vehicle Storage.............................................261 Maintenance Wheels and Tires General Information....................................232 Opening and Closing the Hood..............232 Under Hood Overview - 6.2L...................233 Under Hood Overview - 6.8L..................234 Engine Oil Dipstick......................................235 Engine Oil Check..........................................
Table of Contents MyFord Touch™ General Information...................................359 Settings...........................................................366 Entertainment...............................................376 Phone...............................................................393 Information....................................................399 Climate...........................................................408 Navigation........................................................
6 Super Duty (), enUSA
Introduction Note: Either Ford Motor Company or an authorized Ford dealer may have originally sold this incomplete vehicle to a vehicle modifier who upfitted it. As a result, some of the options and features on this vehicle may differ from what we describe in this manual. ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it.
Introduction Air conditioning system Engine air filter Anti-lock braking system Engine coolant Avoid smoking, flames or sparks Engine coolant temperature Battery Engine oil Battery acid Explosive gas Brake fluid - non petroleum based Fan warning Brake system Fasten safety belt Cabin air filter Front airbag Check fuel cap Front fog lamps Child safety door lock or unlock Fuel pump reset Child seat lower anchor Fuse compartment Child seat tether anchor Hazard warning flashers Cruise con
Introduction Jack Shield the eyes E167012 Keep out of reach of children Stability control Lighting control Windshield wash and wipe E161353 Low tire pressure warning DATA RECORDING Maintain correct fluid level Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle.
Introduction Event Data Recording Note: Event data recorder data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the event data recorder under normal driving conditions and no personal data or information (e.g., name, gender, age, and crash location) is recorded (see limitations regarding 911 Assist and Traffic, directions and Information privacy below).
Introduction Note: Including to the extent that any law pertaining to Event Data Recorders applies to SYNC or its features, please note the following: Once 911 Assist (if equipped) is enabled (set ON), 911 Assist may, through any paired and connected cell phone, disclose to emergency services that the vehicle has been in a crash involving the deployment of an airbag or, in certain vehicles, the activation of the fuel pump shut-off.
Introduction Warranty on Replacement Parts REPLACEMENT PARTS RECOMMENDATION Genuine Ford and Motorcraft replacement parts are the only replacement parts that benefit from a Ford Warranty. Damage caused to your vehicle as a result of the failure of non-Ford parts may not be covered by the Ford Warranty. For additional information, refer to the terms and conditions of the Ford Warranty. Your vehicle has been built to the highest standards using quality parts.
Introduction Using your Vehicle as an Ambulance MOBILE COMMUNICATIONS EQUIPMENT If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the recommendations of the Ford Incomplete Vehicle Manual, Ford Truck Body Builder’s Layout Book and the Qualified Vehicle Modifiers (QVM) Guidelines as well as pertinent supplements.
Introduction are unique to your vehicle. This Owner’s Manual is written primarily for the U.S. and Canadian Markets. Features or equipment listed as standard may be different on units built for Export. Refer to this Owner’s Manual for all other required information and warnings.
Child Safety GENERAL INFORMATION WARNINGS requirements of law. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) and consult your pediatrician to make sure your child seat is appropriate for your child, and is compatible with and properly installed in your vehicle. To locate a child seat fitting station and CPST, contact the NHTSA toll free at 1-888-327-4236 or go to http://www.nhtsa.dot.gov. In Canada, check with your local St.
Child Safety Recommendations for Safety Restraints for Children Child Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger). Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat). Small children Children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 ft. 9 in. (1.
Child Safety Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers, or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). • • Place the vehicle seat upon which the child seat will be installed in the upright position. This vehicle does not require the use of a locking clip.
Child Safety E142530 E142875 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted. 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. 6. Allow the belt to retract to remove slack. The belt will click as it retracts to indicate it is in the automatic locking mode.
Child Safety Using Cinch Tongue Lap and Shoulder Belts (All Front Center, Super Cab and Crew Cab Rear Center Positions) weight of the child is added to the child restraint. It also helps to achieve the proper snugness of the child seat to your vehicle. Sometimes, a slight lean toward the buckle will help to remove remaining slack from the belt. 9. Attach the tether strap (if the child seat is equipped). WARNINGS Airbags can kill or injure a child in a child seat.
Child Safety 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. E162708 2. Slide the tongue up the webbing. E142533 5. While pushing down with your knee on the child seat pull up on the shoulder belt portion to tighten the lap belt portion of the combination lap and shoulder belt. 6.
Child Safety 8. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than 1 inch (2.5 centimeters) of movement for proper installation. 9. Check from time to time to be sure that there is no slack in the lap and shoulder belt. The shoulder belt must be snug to keep the lap belt tight during a crash.
Child Safety F-Series Regular Cab E162710 F-Series SuperCab E162711 Note: For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seat back. If the top of the safety seat hits the head restraint, raise the head restraint to let the child seat fit further rearward. F-Series Crew Cab Attach the tether strap only to the appropriate tether anchor as shown.
Child Safety Tether Strap Attachment (Rear SuperCab Only) There are three loops of webbing just above the back of the rear seat (along the bottom edge of the rear window) in the SuperCab. Use these loops as both routing loops and anchor loops for up to three child safety seat tether straps. You can secure these straps below the back of the seat with rubber bands. To access, reach below the back of the seat and pull the tether loop out of the rubber band securing it. E162712 4. Remove the tether cover. 5.
Child Safety 2. Attach the strap hook onto the loop behind an adjacent seating position. 80 pounds (36 kilograms) and upward to 100 pounds (45 kilograms) if recommended by your child restraint manufacturer). Many state and provincial laws require that children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.45 meters) tall, or 80 pounds (36 kilograms).
Child Safety Types of Booster Seats E70710 • E68924 • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child's head (as measured at the tops of the ears) above the top of the seat.
Child Safety E142597 WARNINGS warnings provided by your vehicle manufacturer. A safety seat that is improperly installed or utilized, is inappropriate for your child's height, age, or weight or does not properly fit the child may increase the risk of serious injury or death. If the booster seat slides on the vehicle seat upon which it is being used, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.
Child Safety Recommendations for attaching child safety restraints for children Restraint Type Combined child and seat weight Use any attachment method as indicated below by X LATCH (lower anchors and top tether anchor) LATCH (lower anchors only) Safety belt Safety belt Safety belt and top and LATCH only tether (lower anchor anchors and top tether anchor) Rear facing Up to 65 lb child seat (29 kg) X Rear facing Over 65 lb child seat (29 kg) X Forward facing child seat Up to 65 lb (29 kg) X Forw
Safety Belts PRINCIPLE OF OPERATION WARNINGS When possible, all children 12 years old and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death. WARNINGS Always drive and ride with your seat back upright and the lap belt snug and low across the hips. Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child.
Safety Belts The safety belt pretensioners at the front seating positions are designed to tighten the safety belts when activated. In frontal and near-frontal crashes, side crashes and rollovers, the safety belt pretensioners may be activated alone or, if the crash is of sufficient severity, together with the front airbags. 2. To unfasten, press the release button and remove the tongue from the buckle.
Safety Belts Fastening the Cinch Tongue WARNING The lap belt should fit snugly and as low as possible around the hips, not across the waist. 1. Pull the lap and shoulder belt from the retractor so that the shoulder belt portion of the safety belt crosses your shoulder and chest. 2. Be sure the belt is not twisted. If the belt is twisted, remove the twist. 3. Insert the belt tongue into the proper buckle for your seating position until you hear a snap and feel it latch. 4.
Safety Belts All safety restraints in the vehicle are combination lap and shoulder belts. The driver safety belt has the first type of locking mode. The front outboard passenger and rear outboard seat safety belts have both types of locking modes described as follows: How to Use the Automatic Locking Mode Vehicle Sensitive Mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Safety Belts Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height: 1. Pull the button and slide the height adjuster up or down. 2.
Safety Belts Conditions of operation If... Then... The driver's safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 12 minutes and the warning chime sounds 4-8 seconds. The driver's safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The safety belt warning light and warning chime turn off.
Safety Belts If... Then... The driver's safety belt is buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder feature will not activate. The driver's safety belt is not buckled when The Belt-Minder feature is activated - the the vehicle has reached at least 6 mph (9.
Safety Belts 4. While the safety belt warning light is on, buckle then unbuckle the safety belt. After Step 4, the safety belt warning light will flash for confirmation. • This will disable the feature if it is currently enabled. • This will enable the feature if it is currently disabled. CHILD RESTRAINT AND SAFETY BELT MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodically to make sure they work properly and are not damaged.
Supplementary Restraints System The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag. PRINCIPLE OF OPERATION WARNINGS Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module.
Supplementary Restraints System Passenger Airbag On and Off Switch (If Equipped) DRIVER AND PASSENGER AIRBAGS WARNINGS Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death. WARNINGS Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries.
Supplementary Restraints System Switch position Passenger airbag status indicator Passenger airbag Off OFF: Lit Disabled ON: Unlit On OFF: Unlit Enabled ON: Lit WARNINGS An infant in a rear-facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should never be placed in the front seats, unless the passenger airbag is turned off.
Supplementary Restraints System 2. The pass airbag off light will briefly illuminate when the ignition is turned to on. This indicates that the passenger airbag is operational. WARNINGS the protection of the airbag, you also may reduce the effectiveness of your safety belt system, which was designed to work with the airbag.
Supplementary Restraints System National Highway Traffic Safety Administration Deactivation Criteria (Excluding Canada) • • WARNING This vehicle has special energy management safety belts for the driver and right front passenger. These particular belts are specifically designed to work with airbags to help reduce the risk of injury in a crash.
Supplementary Restraints System Transport Canada Deactivation Criteria (Canada Only) • • WARNING This vehicle has special energy management safety belts for the driver and right front passenger. These particular belts are specifically designed to work with airbags to help reduce the risk of injury in a crash.
Supplementary Restraints System After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. Properly seated occupants sit upright, lean against the seat back, and center themselves on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event.
Supplementary Restraints System The side airbags are located on the outboard side of the seatbacks of the front seats. In certain sideways crashes, the airbag on the side affected by the crash will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact crashes.
Supplementary Restraints System The Safety Canopy will deploy during significant side crashes or when a certain likelihood of a rollover event is detected by the rollover sensor. The Safety Canopy is mounted to the roof side-rail sheet metal, behind the headliner, above each row of seats. In certain sideways crashes or rollover events, the Safety Canopy will be activated, regardless of which seats are occupied.
Supplementary Restraints System The restraints control module also monitors the readiness of the above safety devices plus the crash and occupant sensors. The readiness of the safety system is indicated by a warning indicator light in the instrument cluster or by a backup tone if the warning light is not working. See Instrument Cluster (page 75). Routine maintenance of the airbag is not required.
Keys and Remote Controls GENERAL INFORMATION ON RADIO FREQUENCIES REMOTE CONTROL This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Keys and Remote Controls Integrated Keyhead Transmitter Programming to the Transmitter 1. 1 With the ignition on, move the memory features to the desired positions using the associated controls. 2 1 3 2 E163048 1. 2. 3. 4. 5. 6. Twist a thin coin in the slot of the transmitter near the key ring to remove the battery cover. Carefully peel up the rubber gasket from the transmitter. It may come off with the battery cover. Remove the old battery Insert the new battery.
Keys and Remote Controls Sounding a Panic Alarm • • Note: The panic alarm will only operate when the ignition is off. E138624 Remote Starting the Vehicle Press the button to activate the alarm. Press the button again or turn the ignition on to deactivate Note: You must press each button within three seconds of each other. Your vehicle will not remote start and the horn will not sound if you do not follow this sequence. it.
Keys and Remote Controls Extending the Vehicle Run Time Repeat Steps 1 and 2 with the vehicle still running to extend the run time for another remote start duration. If the duration is set to last 10 minutes, the duration will extend by another 10 minutes. For example, if the vehicle had been running from the first remote start for five minutes, the vehicle will continue to run now for a total of 20 minutes. Wait at least five seconds before remote starting after a vehicle shutdown.
MyKey™ Configurable Settings PRINCIPLE OF OPERATION With an admin key, you can configure certain MyKey settings when you first create a MyKey and before you recycle the key or restart the vehicle. You can also change the settings afterward with an admin key: • A vehicle speed limit can be set. Warnings will be shown in the display followed by an audible tone when your vehicle reaches the set speed. You cannot override the set speed by fully depressing the accelerator pedal or by setting cruise control.
MyKey™ 1. 2. 3. 4. 5. Programming/Changing Configurable Settings Insert the key you want to program into the ignition. Switch the ignition on. Access the main menu on the information display controls. Press SETUP using the information display buttons until PRESS RESET TO CREATE MYKEY is displayed. Press and release the RESET button. You will see HOLD RESET TO CONFIRM MYKEY in the display. Press and hold the RESET button for two seconds until you see the message MARK THIS AS RESTRICTED in the display.
MyKey™ Note: You can clear or change your MyKey settings at any time during the same key cycle as you created the MyKey. Once you have switched the engine off, however, you will need an admin key to change or clear your MyKey settings. 3. Hold the OK button until ALL MYKEYS CLEARED displays. CLEARING ALL MYKEYS You can find information about your programmed MyKeys by using the information display. CHECKING MYKEY SYSTEM STATUS You can clear all MyKeys within the same key cycle as you created the MyKey.
MyKey™ MYKEY TROUBLESHOOTING Condition I cannot create a MyKey. Potential causes · The key used to start the vehicle does not have admin privileges. · The key used to start the vehicle is the only admin key. There always has to be at least one admin key. · SecuriLock passive anti-theft system is disabled or in unlimited mode. I cannot program the configurable settings. · The key in the ignition does not have admin privileges. · There are no keys programmed to the vehicle. See Creating a MyKey (page 50).
Locks Locking the Doors LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lock and unlock your vehicle. E138623 Press the button to lock all the doors. The turn signals will illuminate. Press the button again within three seconds to confirm that all the doors are closed. The doors will lock again, the horn will sound and the turn signals will illuminate if all the doors are closed.
Locks Battery Saver The autolock feature will unlock all the doors when: • autolock has locked the doors • you stop the vehicle and switch the ignition off or to accessory mode, and • you open the driver door within 10 minutes. The battery saver turns off the interior lamps 30 minutes after you switch the ignition off if a door is open and the dome lamp switch is on. It turns off the interior lamps after 10 minutes if the dome lamp switch is off.
Locks 3. Enter your personal 5-digit code. You must enter each number within five seconds of each other. 4. Press 1·2 on the keypad to save personal code 1. All personal codes will erase and only the factory-set 5-digit code will work. Anti-Scan Feature The keypad will go into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses). This mode disables the keypad for one minute and the keypad lamp will flash.
Locks 2. Switch the ignition off and remove the key. 3. Insert the second key into the ignition and switch the ignition on. The factory-set code will display for a few seconds. Note: The code may not display until after any other warning messages first display.
Security PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) Replacement Keys Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. The integrated keyhead transmitter functions as a programmed ignition key. It operates all the locks, starts the vehicle and acts as a remote control. Note: Your vehicle may have two integrated keyhead transmitters.
Security 1. 2. 3. 4. 5. 6. 7. 8. 9. Insert the first previously programmed coded key into the ignition. Switch the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds. Switch the ignition off and remove the first coded key from the ignition. After three seconds but within 10 seconds of switching the ignition off, insert the second previously coded key into the ignition. Switch the ignition from off to on.
Steering Wheel ADJUSTING THE STEERING WHEEL WARNING Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 110). 3 E95179 2 3. Lock the steering column. AUDIO CONTROL (IF EQUIPPED) You can operate the following functions with the control: 1 2 E95178 1. Unlock the steering column. 2. Adjust the steering wheel to the desired position.
Steering Wheel Media CRUISE CONTROL (IF EQUIPPED) Press repeatedly to scroll through available audio modes. Seek, Next or Previous Press the seek button to: • tune the radio to the next or previous stored preset • play the next or the previous track. Press and hold the seek button to: • tune the radio to the next station up or down the frequency band • seek through a track. E163053 See Cruise Control (page 176).
Steering Wheel Type 2 E163055 See Information Displays (page 81). HEATED STEERING WHEEL (IF EQUIPPED) See MyFord Touch™ (page 359).
Pedals ADJUSTING THE PEDALS (IF EQUIPPED) Note: Never use the controls while your feet are on the accelerator and brake pedals and the vehicle is moving. You can find the control on the left side of the steering column. Press and hold the appropriate side of the control to move the pedals. A B E162916 A. Farther B. Closer You can save and recall the pedal positions with the memory feature. See Memory Function (page 113). Note: Adjust the pedals only when your vehicle is in P (Park).
Wipers and Washers WINDSHIELD WIPERS WINDSHIELD WASHERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washer before wiping a dry windshield. Note: Make sure the windshield wipers are switched off before entering a car wash.
Lighting Headlamp Flasher LIGHTING CONTROL E163268 E163267 • • Pull the lever toward you to flash the headlamps and release the lever to switch the headlamps off. Rotate the headlamp control clockwise to the first position to turn on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Rotate clockwise to the second position to also turn on the headlamps.
Lighting Note: If the vehicle is equipped with autolamps, it will have the headlamps on with windshield wipers feature. If the windshield wipers are turned on, the exterior lamps will turn on with the headlamp control in the autolamp position. INSTRUMENT LIGHTING DIMMER The autolamp system also keeps the lights on for a predetermined amount of time after the ignition switch is turned to off.
Lighting The system switches the headlamps on with a reduced output in daylight conditions. DIRECTION INDICATORS To switch the system on: 1. Switch the ignition on. 2. Switch the lighting control to the off, or parking lamp position. 3. Disengage the parking brake. 4. Make sure the transmission selector lever is not in position P. FRONT FOG LAMPS (IF EQUIPPED) E163272 The turn signal lever does not mechanically lock in the upward or downward position when activated.
Lighting Front Map Lamps (If equipped) The map lamps are located on the overhead console. Press the controls on either side of each map lamp to turn on the lamps. The map lamps also light when: • • • any door is opened. the instrument panel dimmer switch is pressed up until the courtesy lamps come on. any of the remote entry controls are pressed and the ignition is off. E163273 Rear Dome and Map Lamps E163274 Your vehicle may have map lamps within the rear dome lamp.
Windows and Mirrors Note: Perform one-touch up re-calibration with the door closed. Calibrating with the door open will cause the window to continuously bounce back. POWER WINDOWS (IF EQUIPPED) WARNINGS Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves. To reset the function after the battery recharges: 1. Pull the switch all the way up. 2. Hold the switch until the glass stops and continue to hold for two seconds. 3.
Windows and Mirrors Window Lock (If Equipped) Press and hold the control to open the window. Pull and hold the control to close the window. Accessory Delay (If Equipped) A E163057 A Unlock B Lock You can use the window switches for several minutes after you switch the ignition off or until you open either front door. B GLOBAL OPENING (IF EQUIPPED) You can use the remote control to operate the windows with the ignition off. Press the control to lock or unlock the rear window controls.
Windows and Mirrors Note: If you repeatedly fold and unfold the mirrors several times within one minute, the system may disable to protect the motors from overheating. It will reset to normal function automatically within three to five minutes. B A C You can also fold a mirror manually by pushing it toward the door window glass. After you manually adjust the mirror, you will need to reset it.
Windows and Mirrors Telescoping Mirrors (If Equipped) To adjust the mirrors: • Press and hold the control. • When you position the mirrors in or out, the motors will run as long as you hold the control. The running motors allow you to make adjustments as needed. • After positioning the mirrors, return the control to the center position to help protect the motors from overheating. INTERIOR MIRROR E163061 WARNING This feature lets you extend the mirror about 3 inches (75 millimeters).
Windows and Mirrors SUN VISORS WARNINGS When closing the moonroof, you should verify that it is free of obstructions and make sure that children and pets are not in the proximity of the roof opening. Slide-on-rod (If Equipped) You can manually open or close the sliding shade when the moonroof is closed. Pull the shade toward the front of your vehicle to close it. The moonroof controls are located on the overhead console and have a one-touch open and close feature.
Windows and Mirrors Bounce-Back The moonroof will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Pull and hold the SLIDE control within two seconds of a bounce-back event to override this function. While bounce-back is active, the closing force increases for each of the next three times that you close the moonroof. Venting the Moonroof Press and release the TILT control to vent the moonroof. Pull and hold the TILT control to close the moonroof.
Instrument Cluster GAUGES A G E163168 B C F D E A Engine oil pressure gauge B Engine coolant temperature gauge C Transmission fluid temperature gauge D Fuel gauge E Speedometer F Information display See General Information (page 81).
Instrument Cluster Engine Oil Pressure Gauge transmission for extended periods of time with the gauge in the higher than normal area may cause internal transmission damage. Altering the severity of the driving conditions is recommended to lower the transmission temperature into the normal range. If the gauge continues to show high temperatures, see your authorized dealer. Indicates engine oil pressure. The needle should stay in the normal operating range (between L and H).
Instrument Cluster Variations: Driving type (fuel economy conditions) Fuel gauge position Distance-to-empty Highway driving 1/16th 35 miles to 80 miles (56 km to 129 km) Severe duty driving (trailer towing, extended idle) 1/16th 35 miles (56km) Anti-Lock Braking System Information Display If it illuminates when you are driving, this indicates a malfunction. You will continue to have the normal braking system (without ABS) unless the brake system warning lamp is also illuminated.
Instrument Cluster Engine Coolant Temperature WARNING Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Illuminates when the engine coolant temperature is high.
Instrument Cluster Low Fuel Level If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately. Illuminates when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as possible. Note: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter or other vehicle components.
Instrument Cluster Transmission Tow/Haul (If Equipped) Diesel exhaust fluid For more information see your diesel supplement. Illuminates when the tow/haul feature has been activated. If the E161509 light flashes steadily, have the system serviced immediately, damage to the transmission could occur. E163176 Glow plug pre-heat For more information see your diesel supplement. 4X2 (If Equipped) Illuminates momentarily when two-wheel drive high is selected.
Information Displays Information Display Controls (Type 1) GENERAL INFORMATION WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible.
Information Displays INFO TRIP A/B XXX° (if equipped) MYKEY MILES (km) (if programmed) XXX MILES (km) TO E XX.X AVG MPG (L/100km) MPG (L/km) TIMER TBC GAIN (if equipped) EXHAUST FILTER (diesel only) This value is not the same as the average fuel economy display. The running average fuel economy resets to a factory default value if the battery is disconnected. TRIP A/B Registers the distance of individual journeys.
Information Displays EXHAUST FILTER Note: Some options may appear slightly different or not at all if the items are optional. For more information, refer to the Diesel supplement. Note: When returning to the SETUP menu and you selected a non-English language, HOLD RESET FOR ENGLISH will display to change back to English. Press and hold the RESET button to change back to English.
Information Displays SETUP (cont’d) REMOTE WINDOW OPEN On or Off CREATE MYKEY / MYKEY SETUP / CLEAR MYKEY RESET FOR REMOTE START press the RESET button On or Off 5, 10, 15 minutes TBC MODE Electric or EOH TBC EFFORT LOW, MED or HIGH TRAILER SWAY On or Off LANGUAGE = ENGLISH / SPANISH / FRENCH English / Spanish / French 3. Once OIL LIFE SET TO XXX% is displayed, release and press the RESET button to change the Oil Life Start Value. Each release and press will reduce the value by 10%.
Information Displays Information Display Controls (Type 2) (If Equipped) COURTESY WIPE This feature allows for an extra swipe of the wipers after a wipe/wash cycle. CREATE MYKEY / MYKEY SETUP / CLEAR MYKEY For more information, See Creating a MyKey (page 50). RESET FOR REMOTE START (if equipped) REAR PARK AID This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected.
Information Displays Trip A / B Settings E144641 E138660 Fuel Economy Information E144642 E163180 Truck Apps (If Equipped) Display Mode E163181 E163179 Use the arrow buttons to choose between the following gauge options. Gauge Mode Gauges Detail Engine Oil Temperature (Diesel only) Transmission Temperature Compass The compass orientation can be changed between fixed north or rotating north. To change the modes, press OK when the compass display is shown. Use the right arrow to choose the mode.
Information Displays Trip A / B Trip time Trip distance Fuel used Avg MPG (L/100km) Odometer Fuel used Press OK to pause the Trip A or B screen, press again to un-pause. Shows the amount of fuel used for a given trip. Press and hold OK to reset the currently displayed trip information. Average MPG Trip time Shows the average distance traveled per unit of fuel used for a given trip. This shows the elapsed trip time.
Information Displays Fuel Hist. Truck Apps Shows fuel usage as a bar graph based on time. The graph is updated each minute with the fuel economy that was achieved during the prior 5, 10, 30 minutes of driving. In this mode, off-road information depicted with E163181 graphics and trailer towing application options are available. Note: Some items are optional and may not appear.
Information Displays Truck Apps (cont’d) Trailer (cont’d) Press OK for options Rename Trailer Reset Trailer Mileage / Kilometers (if equipped) Trailer disconnected Connection Checklist Disregard this status if your vehicle is not equipped with a factory installed trailer brake controller. This message may appear when an aftermarket TBC is used even when the trailer is connected. Use the up/down arrows to highlight one of these choices and press OK to display the connection checklist.
Information Displays Settings Driver Assist Vehicle Rear Park Aid On or Off Rear Video Camera Camera Delay On or Off Trailer Brake Mode Electric or Elect.
Information Displays Settings (cont’d) MyKey Create MyKey Hold OK to Create MyKey AdvanceTrac Always On or Selectable MAX Speed 80 MPH (130 km/h) or Off Speed Warning 45, 55 or 65 MPH (75, 90 or 105 km/h), Off Volume Limiter On or Off Clear MyKey Hold OK to Clear MyKey Language English, Français, Español Units Distance English Metric Temperature Fahrenheit (°F) Celsius (°C) Information In this mode, you can view different vehicle system information and perform a system check.
Information Displays Compass/Transmission indicator display (if equipped) INFORMATION MESSAGES The compass heading will display in the upper right corner of the information display; the transmission gear indicator displays in the right side of the information display when using the SelectShift Automatic™ transmission feature. These displays will not be shown in all screen modes. For example: when programming certain vehicle features or in certain information menus.
Information Displays Diesel Messages WARNING When the CLEANING EXHAUST FILTER message appears in the information display, do not park near flammable materials, vapors or structures until filter cleaning is complete. Message Action CHECK COOLANT ADDITIVE The coolant additive needs checking. Refer to your diesel supplement for more information. CLEANING EXHAUST FILTER Your vehicle has entered the cleaning mode.
Information Displays Message Action ENGINE TURNS OFF IN 1 SECOND The powertrain control module will intentionally turn the engine off due to your vehicle being in the final second of a countdown. The diesel engine shutdown is a (regulatory) requirement, which may be required of a particular diesel vehicle for sale in states requiring this feature. Refer to your diesel supplement for more information..
Information Displays Message Action SPEED LIMITED TO XX MPH EXHAUST FLUID EMPTY The diesel exhaust fluid is empty. You must replenish the diesel exhaust fluid to resume normal operation of your vehicle. Refer to your diesel supplement for more information. ENGINE IDLED SOON The selective catalytic reduction system detects low exhaust EXHAUST FLUID EMPTY fluid. The engine will eventually enter into an idle only mode. You must replenish the diesel exhaust fluid to resume normal operation of your vehicle.
Information Displays Message Action EXHAUST OVER LIMIT SERVICE NOW You must have your vehicle serviced by an authorized dealer if approximately two hours after the EXHAUST OVERLOADED DRIVE TO CLEAN message has displayed and you have not driven your vehicle above 30 mph (48 km/h) for at least 20 minutes to clean the diesel particulate filter. Refer to your diesel supplement for more information.
Information Displays Message Action TO ENGAGE ELD SLOW TO XX MPH/KM/H TO ENGAGE LOCKING DIFFERENTIAL RELEASE ACCELERATOR PEDAL The electronic locking differential request the release of the accelerator pedal in order to engage. TO ENGAGE ELD RELEASE PEDAL SLOW VEHICLE TO XX KM/H FOR ELD The electronic locking differential requests a certain speed requirement to engage. SLOW VEHICLE TO XX MPH FOR ELD The electronic locking differential requests a certain speed requirement to engage.
Information Displays Key Message Action COULD NOT PROGRAM INTEGRATED KEY You have attempted to program a fifth integrated key. See Replacing a Lost Key or Remote Control (page 49). TO DRIVE: TURN KEY TO ON The factory equipped remote start is active. Turn your key to on to drive. Maintenance Message Action ENGINE OIL CHANGE SOON The engine oil life is nearing its end. See Engine Oil Check (page 235). OIL CHANGE REQUIRED The oil life left reaches 0%. See Engine Oil Check (page 235).
Information Displays Message Action CHECK SPEED DRIVE SAFELY A MyKey is in use, the optional setting is on and your vehicle exceeds a preselected speed. BUCKLE UP TO UNMUTE AUDIO A MyKey is in use and Belt-Minder® is active. MYKEY COULD NOT PROGRAM An attempt failed to program a spare key using two existing MyKeys. Park Aid Message Action CHECK REAR PARK AID The transmission is in R (Reverse) and the park aid is disabled. REAR PARK AID OFF The rear park aid is disabled.
Information Displays Off Road Message Action HILL DESCENT CONTROL OFF The driver has disabled hill descent control mode. FOR HILL DESCENT REDUCE SPEED You have not met the vehicle speed requirement for entry into off-road mode. FOR HILL DESCENT SELECT GEAR The driver is able to select a transmission gear for hill descent mode. HILL DESCENT - DRIVER RESUME CONTROL Hill descent control mode is no longer active and the driver must resume control.
Information Displays Trailer Message Action TRAILER BRAKE GAIN: XX.X [OUTPUT] The current gain setting for the trailer brake. TRAILER BRAKE GAIN: XX.X NO TRAILER The current gain setting for the trailer brake when a trailer is not connected. TRAILER BRAKE MODULE FAULT Accompanied by a single chime, in response to faults sensed by the TBC. See Trailer Sway Control (page 190).
Information Displays Message Action TO EXIT 4X4 LOW APPLY BRAKE You select 2WD and need to apply the brakes in order to exit 4X4 LOW. TO EXIT 4X4 LOW SHIFT TO N You select 2WD while your vehicle is at a stop in 4X4 LOW and you need to shift into Neutral. TO EXIT 4X4 LOW SLOW TO 3 MPH You select 2WD while your vehicle is operating in 4X4 LOW and you need to reduce your speed. SHIFT DELAYED PULL FORWARD May display when shifting to or from 4X4 LOW.
Climate Control MANUAL CLIMATE CONTROL A B C D E I F H G E163163 A Defrost: Press the button to distribute air to the windshield vents and de-mister. Air distribution to instrument panel and footwell vents turn off. You can use this setting to defog and clear the windshield of a thin covering of ice. B Rear defrost and heated mirrors: Turns the heated mirrors off and on as well as the heated rear window, if your vehicle has that feature. See Heated Windows and Mirrors (page 108).
Climate Control F MAX A/C: Turn the temperature control dial all the way past the full cool position to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, the fan automatically adjusts to the highest speed and the temperature dial returns to the full cool position. G Temperature control: Controls the temperature of the airflow in your vehicle. Adjust to select the desired temperature.
Climate Control C Defrost: Press the button to distribute air to the windshield vents and de-mister. Air distribution to instrument panel and footwell vents turn off. You can use this setting to defog and clear the windshield of a thin covering of ice. D Air distribution control: Press these buttons to turn airflow from the windshield, instrument panel, or footwell vents on or off. The system can distribute air through any combination of these vents.
Climate Control Manual Climate Control HINTS ON CONTROLLING THE INTERIOR CLIMATE Note: To reduce fogging of the windshield during humid weather, adjust the air distribution control to the windshield air vents position. General Hints Note: Prolonged use of recirculated air may cause the windows to fog up. Automatic Climate Control Note: You may feel a small amount of air from the footwell air vents regardless of the air distribution setting.
Climate Control Recommended Settings for Heating Vehicle with manual climate control Vehicle with automatic climate control 1 Adjust the fan speed to the center setting. Press the AUTO button. 2 Adjust the temperature control to the midway point of the hot settings. Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary. 3 Select the footwell air vents using the air distribution buttons.
Climate Control Side Window Defogging in Cold Weather Vehicle With Manual Climate Control Vehicle With Automatic Climate Control 1 Select the instrument panel and footwell Press the defrost button. air vents positions through the air distribution control. 2 Press the A/C button. 3 Adjust the temperature control to the desired setting. 4 Adjust the fan speed to the highest setting. 5 Direct the instrument panel side air vents toward the side windows. 6 Close the instrument panel center vents.
Climate Control REMOTE START (IF EQUIPPED) The remote start feature allows you to pre-condition the interior of your vehicle. The climate control system works to achieve comfort according to your previous settings. Note: You cannot adjust the system during remote start operation. Turn the ignition on to return the system to its previous settings. You can now make adjustments normally, but you need to turn certain vehicle-dependent features back on, such as: • Heated seats. • Cooled seats.
Seats We recommend that you follow these guidelines: • Sit in an upright position with the base of your spine as far back as possible. • Do not recline the seat back more than 30 degrees. • Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. • Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 inches (25 centimeters) between your breastbone and the air bag cover.
Seats Lowering the Head Restraint WARNINGS Install the head restraint properly to help minimize the risk of neck injury in the event of a crash. 1. Press and hold button C. 2. Push the head restraint down. Removing the Head Restraint Note: Adjust the seat back to an upright driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable.
Seats Removing the Head Restraint MANUAL SEATS 1. Press and hold buttons C. 2. Pull up the head restraint. WARNING Do not adjust the driver's seat or seat back when your vehicle is moving. Installing the Head Restraint Align the steel stems into the guide sleeves and push the head restraint down until it locks. Moving the Seat Backward and Forward Tilting Head Restraints (If Equipped) The front head restraints tilt for extra comfort.
Seats Manual Lumbar Power Recline (If Equipped) (If Equipped) E162729 E162731 The lumbar support control is located on the outboard side of the seat. Turn the control to adjust your support. Move the switch to recline the seatback forward or rearward. Power Lumbar (If Equipped) POWER SEATS (IF EQUIPPED) WARNINGS Do not adjust the driver's seat or seatback when your vehicle is moving. Adjusting your seatback while the vehicle is in motion may cause loss of control of the vehicle.
Seats This feature will automatically recall the position of the driver's seat, power mirrors, and adjustable pedals. The memory control is located on the driver's door. You can recall the memory positions when you press your remote entry transmitter unlock control (if the transmitter is programmed to a memory position) or, when you enter a valid personal entry code that is programmed to a memory position. The mirrors will move to the programmed position and the seat will move to the easy entry position.
Seats Folding the Rear Seat Back (Crew Cab) E162737 1. Pull the control to release the seat cushion. 2. Rotate the seat cushion up until it locks into the vertical storage position. E162738 1. Pull forward on the control to fold down the seatback. 2. Pull down on the handle and lift up on the seatback to return it to the original position.
Seats Rear Under Seat Storage (Crew Cab) (If Equipped) The rear seat has storage space located under the seat cushion. E162741 Use your vehicle key to lock the storage space. E162739 A HEATED SEATS (IF EQUIPPED) Lift up the lever and flip up the seat cushion to access the storage space and the power point (A).
Seats To operate the heated seats: • Push the indicated side of the control for maximum heat. • Push again to deactivate. E146322 To operate the heated seats, touch the heated seat symbol on the touchscreen to cycle through the various heat settings and off. Warmer settings are indicated by more indicator lights.
Seats CLIMATE CONTROLLED SEATS Cooled Seats (If Equipped) Heated Seats (If Equipped) The cooled seats will only function when the engine is running. WARNING People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time.
Seats To remove a filter: Press the button on the right-hand side of the seat and pull the seatback down to release the armrest. You can also gain access to the cupholders and seatback storage bin. 1. Turn the vehicle off. 2. Push up on the outside rigid edge of the filter until the tabs are released, then remove the filter. E162746 E146321 Pull up on the tab to open the storage bin To install a filter: Lift up on the seatback to return it to the upright position. 1.
Seats E162748 The under-seat storage compartment has a programmable lock. Use the ignition key to program the lock to the compartment. You can power or charge electronics using the under-seat storage compartment auxiliary power point. See Auxiliary Power Points (page 129). REAR SEAT ARMREST (IF EQUIPPED) E162744 Fold the armrest down to use it.
Universal Garage Door Opener (If Equipped) The appearance of your vehicle’s universal garage door opener varies according to your option package. Before programming, make sure you identify which transmitter you have by comparing it to the graphics below: WARNINGS Do not use the system with any garage door opener that does not have the safety stop and reverse feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982).
Universal Garage Door Opener (If Equipped) The system includes two primary features, a garage door opener and a platform for remote activation of devices within the home. This functionality allows you to program garage door openers as well as security devices and home lighting systems. Note: If you cannot locate the learn button, see the Owner’s Manual for your garage door opener or call the toll-free help line at 1-866-572-2728. 3. Press the learn button on the garage door opener motor.
Universal Garage Door Opener (If Equipped) To program another rolling code device, repeat Steps 1 through 6, substituting a different function button in Step 5. Note: You must complete the following step within 2.5 minutes. 4. Enter the corresponding DIP switch settings from left to right into the system by pressing and releasing the buttons corresponding to the settings you noted. Fixed Code Programming Note: It may be helpful to have another person assist you in programming the transmitter. 5.
Universal Garage Door Opener (If Equipped) Note: Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. Note: Make sure you keep the original remote control transmitter for use in other vehicles as well as for future system programming. E164777 Note: We recommend that, upon the sale or lease termination of your vehicle, you erase the programmed function buttons for security reasons.
Universal Garage Door Opener (If Equipped) In-vehicle Programming If the indicator light flashes rapidly for two seconds and then turns to a constant light, you have not programmed the HomeLink button yet. Do the following: This process is to program your hand-held transmitter and your in-vehicle HomeLink button. Press and hold the HomeLink button while you press and release the hand-held transmitter button every two seconds.
Universal Garage Door Opener (If Equipped) 2. The indicator light will begin to flash after 20 seconds. Without releasing the button, follow Step 1 in the Programming section. For questions or comments, contact HomeLink at www.homelink.com or 1-800-355-3515. E142658 Programming to a Genie Intellicode 2 Garage Door Opener 3. Press and hold the function button you want to program for two seconds, then release. Repeat this step.
Universal Garage Door Opener (If Equipped) 4. Press and hold both the programmed Genie button on the hand-held transmitter and the button you want to program. The indicator light on the visor will flash rapidly when the programming is successful. Note: The Genie transmitter will transmit for up to 30 seconds. If HomeLink does not program within 30 seconds you will need to press the Genie transmitter again.
Universal Garage Door Opener (If Equipped) FCC and RSS-210 Industry Canada Compliance This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Auxiliary Power Points 12 Volt DC Power Point • WARNING • • • Do not plug optional electrical accessories into the cigar lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. • On the instrument panel (two locations). Inside the center console. On the rear of the center console. Inside the front under-seat storage compartment (if equipped). Inside the rear under-seat storage compartment (if equipped).
Auxiliary Power Points When the indicator light, located on the power point, is: • on — the power point is ready to supply power. • off — the power point power supply is off; ignition is not on. • flashing — the power point is in fault mode. The power point temporarily turns off power if the 150 watt limit is exceeded. It can also switch to a fault mode when it is overloaded, overheated, or shorted.
Storage Compartments CENTER CONSOLE (IF EQUIPPED) OVERHEAD CONSOLE (IF EQUIPPED) Stow items in the cupholder carefully as items may become loose during hard braking, acceleration or collisions, including hot drinks which may spill. E75193 Press near the rear edge of the door to open it.
Starting and Stopping the Engine If your vehicle is operated in a heavy snow storm or blowing snow conditions, the engine air induction may become partially clogged with snow and ice. If this occurs, the engine may experience a significant reduction in power output. At the earliest opportunity, clear all the snow and ice away from the air induction inlet.
Starting and Stopping the Engine 2. Turn the key to the off position. 3. Apply the parking brake. STARTING A GASOLINE ENGINE Stopping the Engine When Your Vehicle is Moving When you start the engine, the idle speed increases, this helps to warm up the engine. If the engine idle speed does not slow down automatically, have your vehicle checked by an authorized dealer. WARNING Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance.
Starting and Stopping the Engine Important Ventilating Information Do not crank the engine for more than 10 seconds at a time as starter damage may occur. If the engine fails to start, turn the key to off and wait 30 seconds before trying again. If you stop your vehicle and the leave the engine idling for long periods of time, we recommend that you do one of the following: Do not use starting fluid such as ether in the air intake system.
Starting and Stopping the Engine • • • • • • • • temperatures, and be clearly marked Suitable for Use with Outdoor Appliances. Do not use an indoor extension cord outdoors. This could result in an electric shock or become a fire hazard. Use as short an extension cord as possible. Do not use multiple extension cords. Make sure that when in operation, the extension cord plug and heater cord plug connections are free and clear of water. This could cause an electric shock or fire.
Fuel and Refueling • SAFETY PRECAUTIONS WARNINGS Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. • The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury. • Automotive fuels can cause serious injury or death if you misuse or mishandle them.
Fuel and Refueling Use only unleaded gasoline or unleaded gasoline blended with a maximum of 85% ethanol (E-85) in your flex fuel vehicle (FFV). FUEL QUALITY Note: Do not add after-market fuel additive products to your fuel tank. We recommend that you use only high quality fuel without after-market additives or other engine treatments. Do not use: • Note: Your warranty will not cover any vehicle damage, loss of vehicle performance or repairs to your vehicle caused by the use of fuel not recommended.
Fuel and Refueling Refilling With a Portable Fuel Container We recommend regular unleaded gasoline with a pump (R+M)/2 octane rating of 87. Some stations offer fuels posted as regular with an octane rating below 87, particularly in high altitude areas. We do not recommend fuels with an octane rating below 87. WARNINGS The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Fuel and Refueling Note: If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford, Motorcraft® or other certified fuel filler cap is not used. WARNINGS Keep sparks, flames and smoking materials away from fuel. Stay outside your vehicle and do not leave the fuel pump unattended when refueling your vehicle. This is against the law in some places.
Fuel and Refueling Calculating Fuel Economy FUEL CONSUMPTION Do not measure fuel economy during the first 1000 miles (1600 kilometers) of driving (this is your engine’s break-in period); a more accurate measurement is obtained after 2000 miles - 3000 miles (3200 kilometers - 4800 kilometers). Also, fuel expense, frequency of fill ups or fuel gauge readings are not accurate ways to measure fuel economy. Empty reserve is the amount of fuel remaining in the tank after the fuel gauge indicates empty.
Fuel and Refueling • • • • • • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski racks) may reduce fuel economy. Using fuel blended with alcohol may lower fuel economy. Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 kilometers) of driving. Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain.
Fuel and Refueling On-Board Diagnostics (OBD-II) If the service engine soon indicator remains on, have your vehicle serviced at the first available opportunity. Although some malfunctions detected by the OBD-II may not have symptoms that are apparent, continued driving with the service engine soon indicator on can result in increased emissions, lower fuel economy, reduced engine and transmission smoothness, and lead to more costly repairs.
Fuel and Refueling the engine. If the service engine soon indicator blinks eight times, it means that the vehicle is not ready for I/M testing; if the service engine soon indicator stays on solid, it means that the vehicle is ready for I/M testing. The OBD-II system monitors the emission control system during normal driving. A complete check may take several days.
Transmission N (Neutral) AUTOMATIC TRANSMISSION With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. WARNING Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. D (Overdrive) with tow/haul off D (Overdrive) with tow/haul off is the normal driving position for the best fuel economy.
Transmission transmission may downshift, slow the vehicle and control the vehicle speed when descending a hill, without the accelerator pedal being pressed. The amount of downshift braking provided will vary based upon the amount the brake pedal is pressed. 1 (First) • • • To deactivate the tow/haul feature and return to normal driving mode, press the button on the end of the gearshift lever. The TOW HAUL light will no longer be illuminated.
Transmission R (Reverse) Tow/haul delays upshifts to reduce frequency of transmission shifting. Tow/haul also provides engine braking in all forward gears when the transmission is in the D (Overdrive) position; this engine braking will slow the vehicle and assist the driver in controlling the vehicle when descending a grade.
Transmission M (Manual) without Overdrive With the gearshift lever in M (Manual), the driver can change gears up or down as desired. This is called SelectShift Automatic™ transmission (SST) mode. By moving the gearshift lever from drive position D (Overdrive) to M (Manual) you now have control of selecting the gear you desire using buttons on the shift lever. To return to normal D (Overdrive) position, move the shift lever back from M to D. E163184 The transmission will operate in gears one through six.
Transmission By moving the gearshift lever from the D (Drive) position to the M (Manual) position you may now manually select the gear you desire. Only the current gear will be displayed. Press the + button or the – button to upshift or downshift. If the – button is pressed at a vehicle speed that would cause an engine overspeed, the requested gear will flash then disappear and the transmission will remain in the current gear.
Transmission 4. Place fingers into hole where the gearshift lever boot was removed from and pull top half of shroud up and forward to separate it from the lower half of the shroud. There is a hinge at the forward edge of the top shroud. Roll the top half of the shroud upward on the hinge point to clear the hazard flasher button, then pull straight rearward toward the driver’s seat to remove. 5. Remove the top half of the shroud. 6.
Transmission 9. Start the vehicle. Ford Super Duty Vehicles are approved for use as a stationary (including split shaft capability) or mobile power source, within limits and operating guidelines detailed in the Ford Truck Body Builders Layout Book, found at www.fleet.ford.com/truckbbas, and through the Ford Truck Body Builders Advisory Service. Perform Steps 4 through 8 in reverse order, making sure to engage the hinge pivots between the upper and lower halves of the shroud.
Four-Wheel Drive (If Equipped) The 4WD system is engaged or disengaged by rotating the control for both front wheel hub locks from the FREE or LOCK position, then manually engaging or disengaging the transfer case with the floor-mounted shifter. For increased fuel economy in 2WD, rotate both hub locks to the FREE position. USING FOUR-WHEEL DRIVE WARNING For important information regarding safe operation of this type of vehicle, See General Information (page 263).
Four-Wheel Drive (If Equipped) • • • • Using a Manual Shift On Stop (MSOS) 4wd system (If Equipped) provides 4x4 High engagement and disengagement while the vehicle is moving. is operated by a rotary control located on the instrument panel that allows you select 4x2, 4x4 High or 4x4 Low operation. uses auto-manual hub locks that can be engaged and disengaged automatically based on the 4x4 mode selected. will increase fuel economy when used in the recommended AUTO lock mode.
Four-Wheel Drive (If Equipped) Shifting between system modes 5. If shifting to 2H (2WD) with the vehicle at a complete stop, disengage the locking hubs (optional) by rotating the hub lock control from LOCK to FREE. Note: Do not perform these operations if the rear wheels are slipping. Note: Some noise may be heard as the 4x4 system shifts or engages. This is normal. In order to reduce engagement noise, it is recommended that all shifts be performed at speeds below 3 mph (5 km/h).
Four-Wheel Drive (If Equipped) Using the Electronic Shift on the Fly 4WD system (If Equipped) Note: Do not perform this operation if the rear wheels are slipping. Note: Some noise may be heard as the system shifts or engages; this is normal. Note: 4X4 high mode is not intended for use on dry pavement. You can move the control from 2H or 4H at a stop or while driving. The information display may display a message indicating a 4X4 shift is in progress.
Four-Wheel Drive (If Equipped) If SHIFT DELAYED PULL FORWARD is displayed in the information display, transfer case gear tooth blockage is present. To alleviate this condition, place the transmission in a forward gear, move the vehicle forward approximately 5 feet (1.5 meters), and shift the transmission back to neutral to allow the transfer case to complete the range shift. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps.
Four-Wheel Drive (If Equipped) Four-wheel drive (when you select a 4WD mode) uses all four wheels to power the vehicle. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot. Emergency Maneuvers In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid over-driving your vehicle (i.e. turn the steering wheel only as rapidly and as far as required to avoid the emergency).
Four-Wheel Drive (If Equipped) Mud and Water Be cautious of sudden changes in vehicle speed or direction when you are driving in mud. Even four-wheel drive vehicles can lose traction in slick mud. If your vehicle does slide, steer in the direction of the slide until you regain control of your vehicle. Note: Avoid turning on steep slopes or hills. A danger lies in losing traction, slipping sideways and possible vehicle roll over. Whenever driving on a hill, determine beforehand the route you will use.
Four-Wheel Drive (If Equipped) If your vehicle has anti-lock brakes, apply the brakes steadily. Do not pump the brakes. Make sure you allow sufficient distance between you and other vehicles for stopping. Drive slower than usual and consider using one of the lower gears. In emergency stopping situations, apply the brake steadily. Do not pump the brake pedal. See Hints on Driving With Anti-Lock Brakes (page 162).
Four-Wheel Drive (If Equipped) On some Four-wheel drive vehicles, when the transfer case is in the N (Neutral) position, the engine and transmission are disconnected from the rest of the driveline. Therefore, the vehicle is free to roll even if the automatic transmission is in P (Park) or the manual transmission is in gear. Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle.
Rear Axle • LIMITED SLIP DIFFERENTIAL This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the limited-slip axle functions like a standard rear axle. The axle may exhibit a slight noise or vibration during tight turns with low vehicle speed. This is normal behavior and indicates the axle is working.
Rear Axle For 2WD vehicles and vehicles equipped with a manual shift 4WD system E163191 Turn the control to ON. Once the indicator light illuminates in the information E163170 display, both rear wheel axle shafts will be locked together providing added traction. If the indicator does not come on, or the indicator turns off while driving, one of the following has occurred: • • • The vehicle speed is too high. The left and right rear wheel speed difference is too high during an engagement attempt.
Brakes Brake Assist GENERAL INFORMATION Brake assist detects when you brake rapidly by measuring the rate at which you press the brake pedal. It provides maximum braking efficiency as long as you press the pedal, and can reduce stopping distances in critical situations. Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out. Have the system checked by an authorized dealer.
Brakes PARKING BRAKE WARNINGS You must remain in your vehicle once you have activated the system. WARNING Always set the parking brake fully and make sure the transmission selector lever is placed in position P. Failure to set the parking brake and engage park could result in vehicle roll-away, property damage or bodily injury. Turn the ignition to the lock position and remove the key whenever you leave your vehicle.
Brakes 4. Drive off in the normal manner. The brakes will release automatically.
Traction Control PRINCIPLE OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time. If the wheels spin when accelerating on slippery or loose surfaces, the system reduces engine power in order to increase traction. Turn the traction control system off by pressing the stability control button located on the instrument panel.
Traction Control System Indicator Lights and Messages WARNING If a failure has been detected within the AdvanceTrac system, the stability control light will illuminate steadily. Verify that the traction control system was not manually disabled using the stability control button. If the stability control light still illuminates steadily, have the system serviced by an authorized dealer immediately.
Stability Control The AdvanceTrac with Roll Stability Control system helps you keep control of your vehicle when on a slippery surface. The electronic stability control portion of the system helps avoid skids and lateral slides and roll stability control helps avoid a vehicle rollover. The traction control system helps avoid drive wheel spin and loss of traction. See Using Traction Control (page 165).
Stability Control The system automatically activates when you start your engine. The electronic stability control and roll stability control portions of the system can be turned off below 35 mph (56 km/h) and are disabled when the transmission is in position R. See Using Traction Control (page 165). E169377 You can turn off the traction control portion of the system independently. Press the stability control button located on the instrument panel.
Stability Control AdvanceTrac with RSC Features (Single rear wheels only) Button pressed again after deactivation Not illuminated Enabled Enabled Enabled Transfer case switched to Illuminated Disabled Disabled Disabled 4WD Low 1 3 Electronic stability control has reduced sensitivity compared to fully active system. 2 Lamp light starts blinking for four seconds after entering the press and hold state.
Terrain Response (If Equipped) PRINCIPLE OF OPERATION USING HILL DESCENT CONTROL WARNINGS Hill descent control cannot control descent in all surface conditions and circumstances, such as ice or extremely steep grades. Hill descent control is a driver assist system and cannot substitute for good judgment by the driver. Failure to do so may result in loss of vehicle control, crash or serious injury. Press and release the hill descent button located on the E163957 instrument panel.
Terrain Response (If Equipped) • At speeds above 20 mph (32 km/h): When the Hill Descent Control switch is pressed, the Hill Descent Control system will be enabled, the telltale in the cluster will not be illuminated and a message will be displayed in the information display. Refer to the Information Displays for additional Hill Descent Control messages. See Information Messages (page 92).
Parking Aids Note: If your vehicle is equipped with MyKey™, it is possible to prevent turning the sensing system off. See MyKey™ (page 50). PARKING AID (IF EQUIPPED) WARNINGS To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at parking speeds.
Parking Aids WARNINGS Back up as slow as possible since higher speeds might limit your reaction time to stop the vehicle. Use caution when using the rear video camera and the tailgate is ajar. If the tailgate is ajar, the camera will be out of position and the video image may be incorrect. All guidelines will be removed when the tailgate is ajar. A E130178 A Use caution when turning camera features on or off while in reverse (R). Make sure your vehicle is not moving. Coverage area of up to 6 feet (1.
Parking Aids Using the Rear View Camera System To access any of the rear view camera system settings, make the following selections in the touch screen when the transmission is not in reverse (R): • Menu > Vehicle > Rear View Camera The rear view camera system displays what is behind your vehicle when you place the transmission in reverse (R). After changing a system setting, the touch screen shows a preview of the selected features.
Parking Aids D Fixed guideline: Yellow zone E Fixed guideline: Red zone F Rear bumper Manual Zoom WARNING When manual zoom is on, the full area behind your vehicle is not shown. Be aware of your surroundings when using the manual zoom feature. Fixed guidelines are always shown in the display, but the active guidelines only display when the steering wheel is turned. To use active guidelines, turn the steering wheel to point the guidelines toward an intended path.
Cruise Control (If Equipped) Switching Cruise Control On PRINCIPLE OF OPERATION Press and release ON. Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. You can use cruise control when your vehicle speed is greater than 20 mph (30 km/h). The indicator will appear in the instrument cluster. E71340 Setting a Speed 1. Accelerate to the desired speed. 2. Press and release SET+. 3. Take your foot off the accelerator pedal.
Driving Aids STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than three to five seconds when the engine is running. • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir). • Some noise is normal during operation. If excessive, check for low power steering pump fluid level before seeking service by your dealer.
Load Carrying the following terms for determining your vehicle’s weight ratings, with or without a trailer, from the vehicle’s Tire Label or Safety Compliance Certification Label: Base Curb Weight - is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment. Vehicle Curb Weight - is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment.
Load Carrying WARNING The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available. Overloading or improperly loading your vehicle can contribute to loss of vehicle control and vehicle rollover.
Load Carrying E142517 CARGO E143817 GAWR (Gross Axle Weight Rating) - is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position. The total load on each axle must never exceed its Gross Axle Weight Rating.
Load Carrying Note: For trailer towing information refer to the RV and Trailer Towing Guide available at an authorized dealer. GVW E143818 Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position. The Gross Vehicle Weight must never exceed the Gross Vehicle Weight Rating. GVW (Gross Vehicle Weight) is the Vehicle Curb Weight, plus cargo, plus passengers.
Load Carrying E142524 WARNING Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury. GCW GVW E143819 GCWR (Gross Combined Weight Rating) - is the maximum allowable weight of the vehicle and the loaded trailer, including all cargo and passengers, that the vehicle can handle without risking damage.
Load Carrying for operation at Gross Vehicle Weight Rating, not at Gross Combined Weight Rating.) Separate functional brakes should be used for safe control of towed vehicles and for trailers where the Gross Combined Weight of the towing vehicle plus the trailer exceed the Gross Vehicle Weight Rating of the towing vehicle. The Gross Combined Weight must never exceed the Gross Combined Weight Rating. Maximum Loaded Trailer Weight - is the highest possible weight of a fully loaded trailer the vehicle can tow.
Load Carrying 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lb. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lb. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400-750 (5 x 150) = 650 lb.) 5.
Load Carrying be: 635 kilograms - (2 x 99 kilograms) - (12 x 45 kilograms) = 635 - 198 - 540 = -103 kilograms. You will need to reduce the load weight by at least 240 pounds (104 kilograms). If you remove three 100-pound (45-kilogram) cement bags, then the load calculation would be:1400 - (2 x 220) - (9 x 100) = 1400 - 440 900 = 60 pounds. Now you have the load capacity to transport the cement and your friend home.
Load Carrying Tailgate Removal WARNING Always properly secure cargo to prevent shifting cargo or cargo falling from vehicle, which could result in compromised vehicle stability and serious personal injury to vehicle occupants or others. You can remove the tailgate for more loading room. E163092 5. Use a screwdriver to gently pry the spring clip on each connector past the head of the support screw. Disconnect the cable. 6. Disconnect the other cable. 7.
Load Carrying Opening the Step Replace the slip resistance tape or grab handle molding if it appears worn or damaged. Note: Make sure to close and fully latch the step before moving your vehicle. Never drive with the step or grab handle open. Closing the Step 1. Lower the tailgate. 2. Pull the yellow lever on the grab handle to the unlock position. 1. Close the step panel then lift and fully close the step into the tailgate. 2.
Load Carrying E163096 E163099 2. Open the latches to release the panels. 5. Make sure to insert the latch rod into the tailgate hole. Make sure to engage both sides of the locking pins into their holes in the pick-up box. Reverse the steps to store the bed extender. Grocery Mode E163097 3. Rotate the panels toward the tailgate. Repeat Steps 1-3 on the other side of your vehicle. E163100 Follow Steps 1-4 of the tailgate mode instructions by rotating the panels away from the tailgate.
Towing TOWING A TRAILER Load Placement WARNINGS Do not exceed the GVWR or the GAWR specified on the certification label. Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury. To help minimize how trailer movement affects your vehicle when driving: • Load the heaviest items closest to the trailer floor.
Towing Note: Make sure to take into consideration trailer frontal area. 2 Do not exceed 60 feet (5.6 2 meters ) trailer frontal area. TRAILER SWAY CONTROL (IF EQUIPPED) WARNING Note: Exceeding this limitation may significantly reduce the performance of your towing vehicle. Selecting a trailer with a low aerodynamic drag and rounded front design helps optimize performance and fuel economy.
Towing Pickup and box delete Vehicle Engine Rear axle ratio Maximum GCWR 3.73 19000 lb (8618 kg) 4.30 22000 lb (9979 kg) 3.31, 3.55 23500 lb (10659 kg) 3.73 19000 lb (8618 kg) 4.30 22000 lb (9979 kg) 3.31, 3.55 23500 lb (10659 kg) 3.73 19500 lb (8845 kg) 4.30 22500 lb (10206 kg) 3.73 31900 lb (14470 kg) 4.30 35000 lb (15875 * kg) 4.30 40000 lb (18144 kg) 6.2L gas F-250 6.7L diesel F-350 single rear wheel 6.2L gas 6.7L diesel 6.2L gas F-350 dual rear wheel 6.
Towing Chassis cab Vehicle F-350 single rear wheel Rear axle ratio Maximum GCWR 3.73 19000 lb (8618 kg) 4.30 22000 lb (9979 kg) 3.73 23500 lb (10659 kg) 3.73 19500 lb (8845 kg) 4.30 22500 lb (10206 kg) 6.7L diesel 3.73, 4.10 24500 lb (11113 kg) 6.8L gas 4.88 26000 lb (11793 kg) 4.10 26000 lb (11793 kg) 4.30 30000 lb * (13608 kg) 4.88 26000 lb (11793 kg) 4.10 26000 lb (11793 kg) 4.30 35000 lb (15875 * kg) Engine 6.2L gas 6.7L diesel F-350 dual rear wheel 6.2L gas F-450 6.
Towing Chassis cab Vehicle F-550 (19000/ 19500 lb GVWR) Engine Rear axle ratio Maximum GCWR 6.8L gas 4.88 26000 lb (11793 kg) 26000 lb (11793 kg) 6.7L diesel 4.88 Note: The trailer tongue load is considered part of the payload for your vehicle. Reduce the total payload by the final trailer tongue weight. Note: Consult an authorized dealer to determine the maximum trailer weight allowed for your vehicle if you are not sure. Calculating the Maximum Loaded Trailer Weight for Your Vehicle 1.
Towing • Service your vehicle more frequently if you tow a trailer. See your scheduled maintenance information. • If you use a rental trailer, follow the instructions the rental agency gives you. See Load limits in the Load Carrying chapter for load specification terms found on the tire label and Safety Compliance label and instructions on calculating your vehicle's load. Remember to account for the trailer tongue weight as part of your vehicle load when calculating the total vehicle weight.
Towing A B C D Fixed guidelines are always shown in the display, but the active guidelines only display when the steering wheel is turned. To use active guidelines, turn the steering wheel to point the guidelines toward an intended path. If the steering wheel position is changed while reversing, your vehicle might deviate from the original intended path. The active guidelines fade in and out depending on the steering wheel position.
Towing Do not use a hitch that either clamps onto the bumper or attaches to the axle. You must distribute the load in your trailer so that 10-15% for conventional towing or 15-25% for fifth wheel towing of the total weight of the trailer is on the tongue. 4. Measure the height to the top of your vehicle's front wheel opening on the fender a second time. This is H2. 5.
Towing Shorter pick-up boxes, such as the 6½-foot box on the F-250 and F-350, provide less clearance between the cab and the fifth-wheel and gooseneck trailer compared to longer box pick-ups, such as an 8-foot box on the F-250 or F-350. When selecting a trailer and tow vehicle, it is critical to check that this combination provides clearance between the front of the trailer and tow vehicle for turns up to 90 degrees.
Towing Trailer Brakes Integrated Trailer Brake Controller (If Equipped) WARNING Do not connect a trailer's hydraulic brake system directly to your vehicle's brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. WARNING The Ford trailer brake controller has been verified to be compatible with trailers having electric-actuated drum brakes (one to four axles) and some electric-over-hydraulic brakes.
Towing You can adjust the amount of initial trailer brake output by selecting one of three settings through the message center. Ford has tested the trailer brake controller to be compatible with several major brands of electric-over-hydraulic trailer brakes. Contact an authorized dealer for information on which brands you can use.
Towing • • TRAILER CONNECTED: Displays when the system senses a correct trailer wiring connection during a given ignition cycle. TRAILER DISCONNECTED: Displays, accompanied by a single audible time, when the system senses a trailer connection and then a disconnection, either intentional or unintentional, during a given ignition cycle. It also displays if a truck or trailer-wiring fault occurs causing the trailer to appear disconnected.
Towing gain setting is at a point just below trailer wheel lock-up. If towing a heavier trailer, trailer wheel lock-up may not be attainable even with the maximum gain setting of 10. Information Display Warning Messages Note: An authorized dealer can diagnose the trailer brake controller to determine exactly which trailer fault has occurred. However, your Ford warranty does not cover this diagnosis if the fault is with the trailer.
Towing If the message only displays with a trailer connected, the problem is with the trailer wiring. Consult your trailer dealer for assistance. This can be a short to ground (such as a chaffed wire), short to voltage (such as a pulled pin on trailer emergency breakaway battery) or the trailer brakes may be drawing too much current. • • Points to Remember Note: Do not attempt removal of the trailer brake controller without consulting the Workshop Manual. Damage to the unit may result.
Towing • • When you switch the engine off, the controller output is disabled and the display and module shut down. The controller module and display turn on when you switch the ignition on. The trailer brake controller is only a factory-installed or dealer-installed item. Ford is not responsible for warranty or performance of the controller due to misuse or customer installation.
Towing • • • • • When stopped in congested or heavy traffic during hot weather, place the gearshift in position P to aid engine and transmission cooling and to help A/C performance. Turn off the speed control with heavy loads or in hilly terrain. The speed control may turn off automatically when you are towing on long, steep grades. Shift to a lower gear when driving down a long or steep hill. Do not apply the brakes continuously, as they may overheat and become less effective.
Towing Launching or Retrieving a Boat or Personal Watercraft (PWC) TOWING POINTS WARNINGS Using recovery hooks is dangerous and should only be done by a person familiar with proper vehicle recovery safety practices. Improper use of recovery hooks may cause hook failure or separation from the vehicle and could result in serious injury or death. Note: Disconnect the wiring to the trailer before backing the trailer into the water.
Towing • • • • Use a damper device such as a tarp, heavy blanket or piece of carpet draped over the recovery strap to help absorb the energy in the event the strap breaks. Make sure the stuck vehicle is not loaded heavier than its gross vehicle weight rating specified on the certification label. Always align the tow vehicle and stuck vehicle in a straight line (within 10 degrees). Keep bystanders to the sides of the vehicle, at a distance of at least twice the length of the recovery strap.
Towing Note: Towing a two-wheel drive vehicle or an electronic shift-on-the-fly four-wheel drive vehicle with the rear wheels on the ground for more than 50 miles (80 km) or faster than 35 mph (56 km/h) may cause damage to the automatic transmission. Two-wheel Drive Vehicles and Four-wheel Drive Vehicles Equipped with an Electronic-shift Transfer Case Do not tow your vehicle with any wheels on the ground, as vehicle or transmission damage may occur.
Driving Hints Avoid these actions; they reduce your fuel economy: • Sudden accelerations or hard accelerations. • Revving the engine before turning it off. • Idle for periods longer than one minute. • Warm up your vehicle on cold mornings. • Use the air conditioner or front defroster. • Use the speed control in hilly terrain. • Rest your foot on the brake pedal while driving. • Drive a heavily loaded vehicle or tow a trailer. • Carry unnecessary weight (approximately 1 mpg [0.
Driving Hints • • • Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation. Close the windows for high-speed driving. FLOOR MATS DRIVING THROUGH WATER Note: Driving through deep water above the recommended levels can cause vehicle damage.
Driving Hints To install the floor mats, position the floor mat eyelet over the retention post and press down to lock in position. • Remove in reverse order. • SNOWPLOWING Ford recommends that the Super Duty F-Series used for snow removal include the snowplow package option. • Installing the Snowplow • Weight limits and guidelines for selecting and installing the snowplow are in the Ford Truck Body Builders Layout Book, snowplow section, found at www.fleet.ford.com/truckbbas.
Driving Hints Engine temperature while plowing Follow the severe duty schedule in your Scheduled Maintenance information for engine oil and transmission fluid change intervals. When driving with a plow, your engine may run at a higher temperature than normal because the attached snowplow blade will restrict airflow to the radiator. Snowplowing with your Airbag Equipped Vehicle • WARNINGS Do not attempt to service, repair, or modify the airbag supplemental restraint system (SRS) or its fuses.
Roadside Emergencies Trailers shall be covered up to $200 if the disabled eligible vehicle requires service at the nearest authorized dealer. If the trailer is disabled, but the towing vehicle is operational, the trailer does not qualify for any roadside services. ROADSIDE ASSISTANCE Vehicles Sold In The U.S.: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Roadside Emergencies In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off. HAZARD WARNING FLASHERS Note: The hazard warning flashers will operate when the ignition is in any position or if the key is not in the ignition. If used when the engine is not running, the battery will lose charge. As a result, there may be insufficient power to restart your engine.
Roadside Emergencies Note: In the illustration, the bottom vehicle represents the booster vehicle. JUMP STARTING THE VEHICLE WARNINGS The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in personal injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. 1 Use only an adequate-sized cable with insulated clamps.
Roadside Emergencies WARNING Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 4 Jump Starting 1. Start the engine of the booster vehicle and rev the engine moderately, or press the accelerator gently to keep your engine speed between 2000 and 3000 rpms, as shown in your tachometer. 2. Start the engine of the disabled vehicle. 3.
Roadside Emergencies POST-CRASH ALERT SYSTEM The system flashes the turn signal lamps and sounds the horn (intermittently) in the event of a serious impact that deploys an airbag (front, side, side curtain or Safety Canopy) or the safety belt pretensioners.
Customer Assistance These are some of the items that can be found online: • U.S. dealer locator by Dealer Name, City/State, or Zip Code • Owner Manuals • Maintenance Schedules • Recalls • Ford Extended Service Plans • Ford Genuine Accessories • Service specials and promotions. GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized dealer.
Customer Assistance In order to help you serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number. • Your telephone number (home and business). • The name of the authorized dealer and city where located. • The vehicle’s current odometer reading. California Civil Code Section 1793.
Customer Assistance already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.
Customer Assistance In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding on both you and Ford of Canada.
Customer Assistance FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: +971 4 3326084 Toll-Free Number of the Kingdom of Saudi Arabia: 800 8971409 Local Telephone Number of Kuwait: 24810575 FAX: +971 4 3327299 Email: menacac@ford.com www.me.ford.com Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.
Customer Assistance To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator 1200 New Jersey Avenue, Southeast Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Fuses The power distribution box is located in the engine compartment. It has high-current fuses that protect your vehicle's main electrical systems from overloads. FUSE SPECIFICATION CHART Power Distribution Box WARNINGS Always disconnect the battery before servicing high current fuses. If you disconnect and reconnect the battery, you will need to reset some features. See Changing the 12V Battery (page 244).
Fuses Fuse or relay number Fuse amp rating Protected components 11 — 12 30A* 13 — Not used 14 — Not used 15 Diode 16 — 17 15A** 18 — Not used 19 — Not used 20 — Not used 21 — Not used Not used Driver smart window motor Fuel pump (diesel engine) Not used Heated mirror 22 30A* Trailer tow electric brake 23 40A* Blower motor 24 — 25 30A* Wipers 26 30A* Trailer tow park lamps 27 25A* Urea heaters (diesel engine) 28 — 29 Relay Trailer tow park lamps 30 Rela
Fuses Fuse or relay number Fuse amp rating Protected components 20A** Vehicle power 4 (gas engine) 37 10A** Vehicle power 5 (diesel engine) 38 Relay Electronic control module (diesel engine) Powertrain control module (gas engine) 39 10A** 4x4 hub lock 40 15A** 4x4 electronic lock 41 — 42 20A** 43 — Not used 44 — Not used 45 10A** Run/start relay coil 46 10A** Transmission control module keep-alive power (diesel engine) 47 10A** A/C clutch feed 48 Relay Run/start Not us
Fuses Fuse or relay number Fuse amp rating Protected components 60 — Not used 61 — Not used 62 — Not used 63 — Not used 64 — Not used 65 — Not used 66 20A** Fuel pump 67 — 68 10A** Not used 69 — 70 10A** Trailer tow backup lamp Fuel pump relay coil Not used 71 10A** Canister vent (gas engine) 72 10A** Electronic control module relay coil feed keep-alive power Powertrain control module 73 — Not used 74 — Not used 75 — Not used 76 Relay Trailer tow backup la
Fuses Fuse or relay number Fuse amp rating Protected components 86 25A* Anti-lock brake system coil feed 87 20A* Auxiliary power point #5 88 20A* Auxiliary power point #6 89 40A* Starter motor 90 25A* Trailer tow battery charge 91 — 92 20A* Auxiliary power point #4 Not used 93 20A* Auxiliary power point #3 94 25A* Auxiliary switch #1 95 25A* Auxiliary switch #2 96 50A* Anti-lock brake system pump Inverter 97 40A* 98 — 99 40A* 100 — Not used Instrument panel power
Fuses Passenger Compartment Fuse Panel Pull the fuse panel cover toward you to remove it. When the clips of the panel disengage, let the panel fall easily. The fuse panel is in the passenger footwell. Remove the panel cover to access the fuses. Use the provided fuse puller tool to remove a fuse. It is on the fuse panel cover.
Fuses Fuse or relay number Fuse amp rating Protected components 8 10A Power mirror switch 9 10A Auxiliary switch relay #3 10 10A Customer access feed Run/accessory relay 11 10A Instrument cluster 12 15A Interior lighting Lighted running board lamps 13 15A Right turn signals and brake lamps 14 15A Left turn signals and brake lamps 15 15A Backup lamps, Trailer tow backup relay High-mounted stop lamps Reverse signal interior mirror 16 10A Right low beam headlamp 17 10A Left low
Fuses Fuse or relay number Fuse amp rating Protected components 28 15A Ignition switch 29 20A GPS module Radio SYNC 30 15A Parking lamp relay Trailer tow parking lamp relay 31 5A Customer access Trailer brake controller (brake signal) 32 15A Auto dimming mirror Driver and passenger door lock switch illumination Driver and passenger smart window motor Moonroof motor Passenger window switch Power inverter Rear heated seat switch illumination Telescoping mirror switch 33 10A Restraint contr
Fuses Fuse or relay number Fuse amp rating Protected components 45 5A Not used (spare) 46 10A Climate control 47 15A Fog lamps Fog lamp indicator (in switch) 48 30A Circuit breaker 49 Relay Power rear sliding window switch Power windows switch Moonroof switch Delayed accessory CHANGING A FUSE Fuses WARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Maintenance Working with the Engine Off GENERAL INFORMATION 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key (if equipped). 3. Block the wheels. Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers that are there to help you with their professional servicing expertise.
Maintenance 2. Go to the front of the vehicle and locate the secondary release lever, which is located under the front of the hood, to your right of the center of the vehicle (driver's side), toward the headlight. 3. Release the hood latch by pushing the secondary release lever to your left, toward the center of the vehicle. 4. Raise the hood. A 5. To close the hood, lower the hood and allow it to drop the last 8 to 11 inches (20 to 30 centimeters). Note: Make sure that the hood is closed properly.
Maintenance G. Air filter assembly H. Power steering fluid reservoir I. Engine oil filler cap J. Battery UNDER HOOD OVERVIEW 6.8L Note: Refer to the diesel supplement for diesel engine component locations. A B C D E F G E163635 A. Windshield washer fluid reservoir Engine coolant reservoir B. Battery C. Automatic transmission fluid dipstick D. Engine oil filler cap E.
Maintenance F. Power steering fluid reservoir G. Brake fluid reservoir H. Engine coolant reservoir I. Air filter assembly J. Power distribution box A MIN 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the lower hole, add enough oil to raise the level within the lower and upper holes.
Maintenance ENGINE COOLANT CHECK Checking the Engine Coolant Note: If your vehicle is equipped with a diesel engine, refer to the Diesel Supplement. When the engine is cold, check the concentration and level of the engine coolant at the intervals listed in the scheduled maintenance information. See Scheduled Maintenance (page 440). E142732 Only use oils certified for gasoline engines by the American Petroleum Institute (API).
Maintenance Adding Engine Coolant • WARNINGS Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.
Maintenance Recycled Engine Coolant What You Should Know About FailSafe Cooling Ford Motor Company does not recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available. If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.
Maintenance When Fail-Safe Mode Is Activated Engine Fluid Temperature Management (If Equipped) WARNINGS Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs.
Maintenance • • • Checking Automatic Transmission Fluid (If Equipped) the engine coolant temperature gauge moves fully into the red (hot) area the coolant temperature warning light illuminates the service engine soon indicator illuminates. For scheduled intervals of the fluid checks and changes, See Scheduled Maintenance (page 440). Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, i.e.
Maintenance E163742 E163739 Type B For vehicles equipped with 5-speed transmissions, check the fluid at the normal operating temperature of 151°F (66°C) to 170°F (77°C) on a level surface. For vehicles equipped with 6-speed transmissions, check the fluid at the normal operating temperature of 196°F (91°C) to 215°F (102°C) on a level surface. The normal operating temperature can be reached after approximately 19 mi (30 km).
Maintenance E163744 E163745 Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and engagement concerns, and possible damage. Type B High fluid levels can be caused by an overheating condition. Adjusting Automatic Transmission Fluid Levels Note: Use of a non-approved automatic transmission fluid may cause internal transmission component damage.
Maintenance TRANSFER CASE FLUID CHECK BRAKE FLUID CHECK Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately. POWER STEERING FLUID CHECK Check the power steering fluid. See Scheduled Maintenance (page 440).
Maintenance 6. Recheck the fluid level in the reservoir. Do not add fluid if the level is between the MIN and MAX range. 7. If the fluid is low, add fluid in small amounts, continuously checking the level until it is between the MIN and MAX range. For proper fluid type, See Capacities and Specifications (page 301). Be sure to put the cap back on the reservoir. CHANGING THE 12V BATTERY WASHER FLUID CHECK Batteries normally produce explosive gases which can cause personal injury.
Maintenance Note: Electrical or electronic accessories or components added to the vehicle by the dealer or the owner may adversely affect battery performance and durability. 6. Release the parking brake. With your foot on the brake pedal and with the A/C on, put the vehicle in D and allow the engine to idle for at least one minute. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. 7.
Maintenance control fan, heated steering wheel, audio and navigation system. A message may be shown in the information displays to alert the driver that battery protection actions are active. These messages are only for notification that an action is taking place, and not intended to indicate an electrical problem or that the battery requires replacement.
Maintenance Headlamp Aiming Target A E165794 2. Release the wiper blade lock (A) and separate the wiper blade from the wiper arm. 3. Install in the reverse order. Note: Make sure that the wiper blade locks into place. Lower the wiper arm and blade back on the windshield. The wiper arms will automatically return to their normal position when you turn the ignition on. Vertical Aim Adjustment Procedure • 1. • E142592 Replace wiper blades at least once per year for optimum performance.
Maintenance 5. Locate the vertical adjuster on each headlamp. Using a Phillips #2 screwdriver, turn the adjuster either clockwise or counterclockwise in order to adjust the vertical aim of the headlamp. 6. Repeat steps 3 thru 5 to adjust the other headlamp. 7. Close the hood and turn off the lamps. Horizontal Aim Adjustment E142465 Horizontal aim is not required for this vehicle and is not adjustable. 4.
Maintenance E163821 1. 2. 3. 4. 5. 7. Pull the assembly straight out disengaging one snap clip from the fender. 8. Disconnect the electrical connector by squeezing the release tab and pushing the connector forward, then pulling it rearward. Using masking tape or a marker, make an alignment mark between one of the grille brackets and the vehicle radiator support to ensure correct grille alignment during the installation procedure. Do not scratch the black coating from the radiator support.
Maintenance Examples of unacceptable moisture (usually caused by a lamp water leak) are: • Water puddle inside the lamp. • Large water droplets, drip marks or streaks present on the interior of the lens. Take your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present. Replacing Front Clearance and Identification Lamp Bulbs (If Equipped) E163824 10. 11.
Maintenance Replacing Fog Lamp Bulbs (If Equipped 2. Remove the two bolts from the tail lamp assembly and carefully pull the lamp assembly from the tailgate pillar by releasing the two retaining tabs. 3. Rotate the bulb socket counterclockwise and remove from lamp assembly 4. Pull the bulb straight out of the socket. 5. Install the new bulb in reverse order. Chassis Cabs E163826 1. Make sure the headlamps are off. 2. Remove the bulb socket from the fog lamp by turning it counterclockwise. 3.
Maintenance 1. Make sure the headlamps are off. 2. Remove the screws and lamp assembly from the vehicle as wiring permits. 3. Remove the bulb socket by rotating it counterclockwise. 4. Pull the bulb straight out of the socket. 5. Install the new bulb in reverse order. 1. Reach behind the rear bumper to locate the bulb. 2. Twist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly. 3. Pull out the old bulb from the socket and push in the new bulb. 4.
Maintenance Function Number of Bulbs Trade name High-mount brake lamp 1 912 Cargo lamp 2 912 Map lamp 2 12V6W Dome/reading lamps 3 578 Interior visor lamp 2 2825 Mirror turn signal 2 2825 Mirror clearance lamp 2825 Front clearance lamps and 5 194 4 LED Rear identification 3 193 Underhood Lamp 1 1 front identification lamps 1 Rear fender clearance 1 2 2 906 LED (if equipped) To replace all instrument panel lights - see your authorized dealer 1 Dual rear wheels, if equi
Maintenance CHANGING THE ENGINE AIR FILTER WARNINGS To reduce the risk of vehicle damage and personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. To reduce the risk of vehicle damage and personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. E163756 2.
Maintenance E163758 E163760 5. Release the three clamps that secure the cover to the air filter housing. Push the air filter cover toward the center of the vehicle and up slightly to release it. 6. Remove the air filter element from the air filter housing. 7. Install the new air filter element. 10. E163759 8. Replace the air filter housing cover and secure all the clamps.
Vehicle Care GENERAL INFORMATION CLEANING THE EXTERIOR Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash.
Vehicle Care • • • • Wash your vehicle first, using cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash. Use Motorcraft Custom Bright Metal Cleaner. Apply the product as you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag. • • • • Do not apply cleaning product to hot surfaces and do not leave cleaning product on chrome surfaces longer than the time recommended.
Vehicle Care • • Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations. Cover the battery, power distribution box, and air filter assembly to prevent water damage when cleaning the engine. WARNINGS On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a collision.
Vehicle Care Clean the instrument panel and cluster lens with a clean, damp, white cotton cloth, then use a clean and dry white cotton cloth to dry these areas. • • • • 4. Remove the soaked cloth and if it is not soiled badly, use this cloth to clean the area by using a rubbing motion for 60 seconds. 5. Following this, wipe area dry with a clean, white, cotton cloth. Avoid cleaners or polishes that increase the gloss of the upper portion of the instrument panel.
Vehicle Care • • alcohol solutions solvents or cleaners intended specifically for rubber, vinyl and plastics. In order to lessen the appearance of certain scratches and other wear marks, apply conditioner on the affected area following the same instructions as in the Conditioning section.
Vehicle Care CLEANING THE ALLOY WHEELS (IF EQUIPPED) VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time (30 days or more), read the following maintenance recommendations to make sure your vehicle stays in good operating condition. Note: Do not apply a cleaning chemical to warm or hot wheel rims and covers. Note: Some automatic car washes may cause damage to the finish on your wheel rims and covers.
Vehicle Care Engine Miscellaneous • • • • The engine oil and filter should be changed prior to storage, as used engine oil contain contaminates that may cause engine damage. Start the engine every 15 days. Run at fast idle until it reaches normal operating temperature With your foot on the brake, shift through all the gears while the engine is running.
Wheels and Tires Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Wheels and Tires How your vehicle differs from other vehicles Sport utility vehicles and trucks can differ from some other vehicles in a few noticeable ways. Your vehicle may be: E168583 As a result of the above dimensional differences, Sport utility vehicles and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition.
Wheels and Tires U.S. Department of Transportation Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. TIRE CARE Information About Uniform Tire Quality Grading Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Wheels and Tires The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Federal Motor Vehicle Safety Standard No. 139. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
Wheels and Tires *kPa: Kilopascal, a metric unit of air pressure. *PSI: Pounds per square inch, a standard unit of air pressure. *Cold tire pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 kilometers).
Wheels and Tires A. P: Indicates a tire, designated by the Tire and Rim Association, that may be used for service on cars, sport utility vehicles, minivans and light trucks. Note: If your tire size does not begin with a letter this may mean it is designated by either the European Tire and Rim Technical Organization or the Japan Tire Manufacturing Association. B. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge.
Wheels and Tires Letter rating mph ( km/h) W 168 mph (270 km/h) J. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. K. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire.
Wheels and Tires *Temperature: The temperature grades are A (the highest), B and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. M. Maximum Inflation Pressure: Indicates the tire manufacturers' maximum permissible pressure or the pressure at which the maximum load can be carried by the tire.
Wheels and Tires D. Maximum Load Single lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a single; defined as two tires (total) on the rear axle. A. T: Indicates a type of tire, designated by the Tire and Rim Association, that is intended for temporary service on cars, sport utility vehicles, minivans and light trucks. B. 145: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge.
Wheels and Tires Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate.
Wheels and Tires Note: Do not reduce tire pressure to change the ride characteristics of the vehicle. If you do not maintain the inflation pressure at the levels specified by Ford, your vehicle may experience a condition known as shimmy. Shimmy is a severe vibration and oscillation in the steering wheel after the vehicle travels over a bump or dip in the road that does not dampen out by itself.
Wheels and Tires Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure.
Wheels and Tires any procedure involving tire inflation, the technician or individual must utilize a remote inflation device, and ensure that all persons are clear of the trajectory area.
Wheels and Tires 1 E161438 wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety, tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail. Improper or inadequate vehicle maintenance can cause tires to wear abnormally.
Wheels and Tires Tire Wear or suspected have the tire inspected by a tire professional. Tires can be damaged during off-road use, so inspection after off-road use is also recommended. Age WARNING Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed, inflation pressure) the tires experience throughout their lives.
Wheels and Tires describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
Wheels and Tires The two front tires or two rear tires should generally be replaced as a pair. The tire pressure sensors mounted in the wheels are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system. If the tire pressure monitoring system indicator is flashing, the system is malfunctioning.
Wheels and Tires *Avoid fast starts, stops and turns *Avoid potholes and objects on the road *Do not run over curbs or hit the tire against a curb when parking Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically.
Wheels and Tires Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare wheel and tire assembly. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels.
Wheels and Tires If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. We do not recommend splitting up the dual rear wheels. Rotate them side to side as a set. After tire rotation, inflation pressures must be adjusted for the tires new positions in accordance with vehicle requirements. Sometimes irregular tire wear can be corrected by rotating the tires.
Wheels and Tires Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
Wheels and Tires You should always have your tires serviced by an authorized dealer. When Your Temporary Spare Tire is Installed Check the tire pressure periodically (at least monthly) using an accurate tire gauge. See Inflating Your Tires in this chapter. When one of your road tires needs to be replaced with the temporary spare, the system will continue to identify an issue to remind you that the damaged road wheel and tire assembly needs to be repaired and put back on your vehicle.
Wheels and Tires Low tire pressure warning light Possible cause Customer action required Solid warning light Tire(s) under-inflated Make sure tires are at the proper pressure. See Inflating your tires in this chapter. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar), the vehicle must be driven for at least two minutes over 20 mph (32 km/h) before the light turns off.
Wheels and Tires When Inflating Your Tires Tire Pressure Monitoring System Reset Procedure When putting air into your tires (such as at a gas station or in your garage), the tire pressure monitoring system may not respond immediately to the air added to your tires.
Wheels and Tires • • • To reduce the chances of interference from another vehicle, perform the system reset procedure at least three feet (one meter) away from another Ford Motor Company vehicle undergoing the system reset procedure at the same time. Do not wait more than two minutes between resetting each tire sensor or the system will time-out and the entire procedure will have to be repeated on all four wheels. A double horn will sound indicating the need to repeat the procedure. 5.
Wheels and Tires 11. Set all four tires to the recommended air pressure as indicated on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position) or Tire Label located on the B-Pillar or the edge of the driver's door.
Wheels and Tires • • • • • • • Exceed 50 mph (80 km/h) Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label. Tow a trailer. Use snow chains on the end of the vehicle with the dissimilar spare tire. Use more than one dissimilar spare tire at a time. Use commercial car washing equipment. Try to repair the dissimilar spare tire. • • Use commercial car washing equipment. Use snow chains on the end of the vehicle with the dissimilar spare wheel and tire assembly.
Wheels and Tires Tool Location SuperCab: Under rear bench seat on passenger side Jack handle, lug wrench, lug wrench exten- Regular cab: Fastened to floor behind driver sion (only available on dual rear wheel seat vehicles) and wheel chock (only available SuperCab: Fastened to floor under rear seat on single rear wheel vehicles equipped with Crew Cab: Fastened to floor behind rear a diesel engine) seat at driver side Key and spare tire lock In the glove box Removing the Spare Tire (With Spare Tire Carri
Wheels and Tires B A B A E162798 1. E162800 Attach the spare tire lock key (A) to the jack handle (B). 5. Lift the spare tire on end to access the tether attachment. 6. Use the lug wrench to remove the lug nut from the spare tire tether. 7. If not replacing the spare or flat tire to the underbody storage area, raise the wheel retainer up into the installed position. 8.
Wheels and Tires F-250 and F-350 Single Rear Wheel Vehicles WARNINGS Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Always use the jack provided as original equipment with your vehicle.
Wheels and Tires Note: Make sure the jack fits onto the flat area on the outboard side of the differential. Jacking the Vehicle E162811 E162804 1. Front passenger side (4x4) Note: View shown from the rear of the vehicle to clearly identify the jack point. Place the jack directly under the axle. 2. 3. E162805 Rear Note: Jack at the specified locations to avoid damage to the vehicle. 4. 5. 6. 7. 8.
Wheels and Tires 1 6 7 4 3 5 8 E161441 2 E162821 8-lug nut torque sequence 10 If the ornament retention towers are aligned between the studs or lug nuts, the ornament is improperly installed. This improper installation may appear and sound correct, but will not keep the ornament on the vehicle. Ornaments improperly installed in this manner will fall off or become loose with minimal force or impact.
Wheels and Tires Note: View shown from the rear of the vehicle to clearly identify the jack point. Note: Place the jack directly under the axle and inboard of the radius arm so that the jack clears the radius arm. E162813 Front (4x2): F-350 dual rear wheel Note: Place the jack directly under the I-beam. E162816 Front: F-450 and F-550 E162814 Front driver side (4x4): F-350 dual rear wheel Note: Make sure the jack fits onto the flat area on the outboard side of the differential housing.
Wheels and Tires Jacking the Vehicle 8. Stow the jack, jack handle and lug wrench. Make sure the jack is securely fastened so it does not rattle when driving. 9. Unblock the wheels. 1 6 7 4 3 E162819 1. Insert the jack handle into the pump linkage. 2. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Note: Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack's rated capacity.
Wheels and Tires 1. Align the ornament with the lug nuts. A is the clip and B is the flange. E162825 E162823 2. Hold the ornament so that all of the retention clips are sitting on the flange of the lug nuts. A C D E162826 Stowing the Flat or Spare Tire B Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire.
Wheels and Tires to the maximum tightness. Tighten to the best of your ability, to the point where the ratchet/slip occurs, if possible. The spare tire carrier will not allow you to overtighten. If the spare tire carrier ratchets or slips with little effort, take the vehicle to your authorized dealer for assistance at your earliest convenience. 6. Check that the tire lies flat against the frame and is properly tightened. Try to push or pull, then turn the tire to be sure it will not move.
Wheels and Tires TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications WARNING When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel.
Wheels and Tires E145950 A Wheel pilot bore Inspect the wheel pilot hole and mounting surface prior to installation. Remove any visible corrosion or loose particles.
Capacities and Specifications ENGINE SPECIFICATIONS Engine 6.2L V8 Engine 6.8L V10 Engine Cubic inches 378 413 Required fuel Minimum 87 octane Minimum 87 octane Firing order 1-5-4-8-6-3-7-2 1-6-5-10-2-7-3-8-4-9 Ignition system Coil on plug Coil on plug Spark plug gap 0.041-0.047 inch (1.04-1.20 mm) 0.039-0.043 inch (1.001.10mm) Compression ratio 9.8:1 9.2:1 6.8L Engines with A/C Drivebelt Routing 6.2L Engines E163762 6.
Capacities and Specifications MOTORCRAFT PARTS Component 6.2L V8 engine 6.8L V10 engine Air filter element FA-1883 FA-1883 Oil filter FL-820-S FL-820-S Battery (standard) BXT-65-650 BXT-65-650 Battery (optional) BXT-65-750 BXT-65-750 Spark plugs-platinum CYFS12FP/SP-526 HJFS-24FP/SP-509 Seat filter FS-104 FS-104 Windshield wiper blade WW-2201-P WW-2201-P 1 1 For spark plug replacement, see an authorized dealer. Replace the spark plugs at the appropriate intervals.
Capacities and Specifications VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel. C Make, vehicle line, series, body type D Engine type E Check digit F Model year G Assembly plant H Production sequence number VEHICLE CERTIFICATION LABEL E142476 Please note that in the graphic, XXXX is representative of your vehicle identification number.
Capacities and Specifications The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label shall be affixed to either the door hinge pillar, the door latch post, or the edge of the door near the door latch, next to the driver's seating position.
Capacities and Specifications TECHNICAL SPECIFICATIONS Item Capacity Ford part name or equivalent Ford part number / Ford specification Front axle 5.8 pints (2.8L) Motorcraft SAE 80W-90 Premium Rear Axle Lubricant XY-80W-90–QL / WSP-M2C197–A Spindle bearing — High Temperature 4X4 Front Axle and Wheel Bearing Grease XG-11 / WSS-M1C267-A1 6.9 pints (3.3L) Motorcraft SAE 75W-140 Synthetic Rear Axle Lubricant XY-75W140–QL (U.S.) / WSL-M2C192-A Rear axle - F-250/350 1 (10.
Capacities and Specifications Item Capacity Ford part name or equivalent Ford part number / Ford specification Engine coolant (6.8L 26.7 quarts (25.3L) Motorcraft Orange Antifreeze/Coolant Prediluted VC-3DIL-B (U.S.) / WSS-M97B44-D2 3 V10) Engine and fuel coolant (diesel engine) Refer to the diesel supplement. Engine oil (6.2L V8 and 7.0 quarts (6.6L) 6.
Capacities and Specifications Item Capacity Ford part name or equivalent Ford part number / Ford specification Transmission, parking brake linkages and pivots, brake pedal shift — Motorcraft Premium Long-Life Grease XG-1-E / WSD-M1C227-A Power steering fluid — Motorcraft MERCON XT-10–QLV / LV Automatic transmission MERCON LV Transfer case fluid 2.0 quarts (1.9L) Automatic transmission 17.5 quarts (16.
Capacities and Specifications Item Capacity Air conditioning refrigerant compressor oil (Diesel engines) 10 Ford part name or equivalent 3.53 fl oz (104.
Capacities and Specifications 1 Add 8 oz. (236 ml) of Additive Friction Modifier XL-3 or equivalent meeting Ford Specification EST-M2C118–A for complete refill of limited slip Ford axles. Ford design rear axles contain a synthetic lubricant that does not require changing unless you submerge the axle in water.
Audio System AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: • AM: 530, 540-1700, 1710 kHz • FM: 87.9-107.7, 107.9 MHz GENERAL INFORMATION Radio Frequencies and Reception Factors Radio Reception Factors Distance and strength The further you travel from an FM station, the weaker the signal and the weaker the reception.
Audio System • • MP3 folder mode represents a folder structure consisting of one level of folders. The CD player numbers all MP3 tracks on the disc (noted by the .mp3 file extension) and all folders containing MP3 files, from F001 (folder) T001 (track) to F253 T255. Creating discs with only one level of folders helps with navigation through the disc files. In track mode, the system displays and plays the structure as if it were only one level deep (all .
Audio System A CLK: Press this button to switch the display between the clock and radio frequency. To set the time, press and hold the button until the hours start to flash. Press the arrow buttons (B) to adjust he hours, then repeat to set the minutes. Press CLK again to exit clock mode. B Tune: Press these arrow buttons to manually search through the radio frequency band. Press and hold for a fast search. In AUDIO mode, press the buttons to adjust different sound settings.
Audio System B A C R D Q E P F O G N M L K J I H E169515 A Eject: Press to eject a CD. B CD slot: Insert a CD. C Tune: Press to search through the radio frequency band manually. Press and hold for a fast search. D Phone: Press to access the phone features of the SYNC system. See SYNC™ (page 323). E MENU: Press to access different audio system features. If your vehicle is equipped with satellite radio, you can access different menus by pressing OK.
Audio System Track/Folder is only available on MP3 files when in CD mode. In track mode, pressing the SEEK arrows allows you to scroll through all the tracks on the disc. In folder mode, pressing the SEEK arrows allows you to scroll through all the tracks within the selected folder. Press the FOLDER buttons to access other folders. COMPRESS (Compression) is only available in CD and MP3 modes. Switching compression on brings the soft and loud passages together for a more consistent listening level.
Audio System Note: The MyFord Touch system controls most of the audio features. See MyFord Touch™ (page 359). AUDIO UNIT - VEHICLES WITH: SONY AM/FM/CD WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Audio System F Seek, Reverse and Fast Forward: In radio mode, select a frequency band and press one of these buttons. The system stops at the first station it finds in that direction. In Sirius mode, press these buttons to select the previous or next channel. If a specific category is selected (such as Jazz, Rock or News), use these buttons to find the previous or next channel in the selected category. In CD mode, press these buttons to select the previous or next track.
Audio System HD Radio Reception and Station Troubleshooting Potential reception issues Reception area If you are listening to a multicast station and you are on the fringe of the reception area, the station may mute due to weak signal strength. If you are listening to HD1, the system switches back to the analog broadcast until the digital broadcast is available again.
Audio System Potential station issues Issues Echo, stutter, skip or repeat in audio. Increase or decrease in audio volume. Cause Action This is poor time alignment No action required. This is a by the radio broadcaster. broadcast issue. Sound fading or blending in The radio is shifting between No action required. The and out. analog and digital audio. reception issue may clear up as you continue to drive. * There is an audio mute delay when selecting HD2 or HD3, multicast preset or Direct Tune.
Audio System Note: This receiver includes the eCos real-time operating system. eCos is published under the eCos License. Satellite Radio Reception Factors Potential satellite radio reception issues Antenna obstructions For optimal reception performance, keep the antenna clear of snow and ice build-up and keep luggage and other material as far away from the antenna as possible.
Audio System Troubleshooting Radio display Condition Possible action Acquiring Radio requires more than two seconds to produce audio for the selected channel. Sat Fault/SIRIUS system failure There is an internal module If this message does not or system failure present. clear shortly, or with an ignition key cycle, your receiver may have a fault. See an authorized dealer for service. Invalid Channel The channel is no longer available. Tune to another channel or choose another preset.
Audio System The auxiliary input jack allows you to connect and play music from your portable music player through your vehicle speakers. You can use any portable music player designed for use with headphones. Your audio extension cable must have male 1/8th-inch (3.5 millimeter) connectors at each end. AUDIO INPUT JACK WARNINGS Driving while distracted can result in loss of vehicle control, crash and injury.
Audio System The USB port allows you to plug in media playing devices, memory sticks and charge devices (if supported). See SYNC™ (page 323). MEDIA HUB (IF EQUIPPED) The media hub is located in a compartment on top of the instrument panel. Push down on the top of the compartment to access the media hub. C A B E163162 A A/V inputs B SD card slot C USB ports See MyFord Touch™ (page 359).
SYNC™ (If Equipped) GENERAL INFORMATION E142598 • SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cellular phone and portable media player. This allows you to: • Make and receive calls. • Access and play music from your portable music player. • Use 911 Assist, Vehicle Health Report and SYNC Services (Traffic, Directions * & Information). • • • • • * These features require activation. Make sure that you review your device's manual before using it with SYNC.
SYNC™ (If Equipped) Times are subject to change due to holidays. When using SYNC: • Do not operate playing devices if the power cords or cables are broken, split or damaged. Place cords and cables out of the way, so they do not interfere with the operation of pedals, seats, compartments or safe driving abilities. • Do not leave playing devices in your vehicle during extreme conditions as it could cause them damage. See your device's manual for further information.
SYNC™ (If Equipped) System data cannot be accessed without special equipment and access to the vehicle's SYNC module. Ford Motor Company and Ford of Canada will not access the system data for any purpose other than as described absent consent, a court order, or where required by law enforcement, other government authorities, or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.
SYNC™ (If Equipped) System Interaction and Feedback The default setting is to a higher level of interaction in order to help you learn to use the system. You can change these settings at any time. The system provides feedback through audible tones, prompts, questions and spoken confirmations depending on the situation and the chosen level of interaction (voice settings). You can customize the voice recognition system to provide more or less instruction and feedback.
SYNC™ (If Equipped) When you say: The system: "Media candidate lists off" Makes a best guess from the media candidate list. You may still occasionally be asked questions. "Media candidate lists on" Clarifies your voice command for media candidates. "Phone candidate lists off" Makes a best guess from the phone candidate list. You may still occasionally be asked questions.
SYNC™ (If Equipped) Pairing a Phone for the First Time 1. Note: SYNC can support downloading up to approximately 1000 entries per Bluetooth-enabled cellular phone. 2. 3. Note: Make sure to switch on the ignition and the radio. Put the transmission in position P. 4. Note: To scroll through the menus, press the up and down arrows on your audio system. 5. Wirelessly pairing your phone with SYNC allows you to make and receive hands-free calls. 6. 1. Press the phone button.
SYNC™ (If Equipped) "PHONE" "DIAL" 2 "Call history outgoing" "411 (four-one-one)", "911" (nine-oneone) 2 "Connections" "Dial" "700" (seven hundred) 1,3 "800" (eight hundred) "Go to privacy" "900" (nine hundred) "Hold" "Pound" (#) "Join" "Menu" "Number <0-9>" 2,4 "Phone book " "Asterisk" (*) 2 "Clear" (deletes all entered digits) "Phone book at home" "Delete" (deletes one digit) 2 "Plus" 2 "Phone book at office" "Phone book at work" "Star" 2 Note: To exit d
SYNC™ (If Equipped) Receiving Calls "MENU" When receiving a call, you can: • Answer the call by pressing the phone button. • Reject the call by pressing and holding the phone button. • Ignore the call by doing nothing. "Signal" "Text message inbox" Words in ( ) are optional and do not have to be spoken for the system to understand the command.
SYNC™ (If Equipped) When you select: You can: 2. Access the desired contact through SYNC or use voice commands to place the second call. Once actively in the second call, press MENU. 3. Scroll to Join Calls, and press OK. Press OK again when Join Calls? appears. Phonebook Access your phonebook contacts. 1. Press OK to select, and then scroll through your phonebook contacts. 2. Press OK again when the desired selection appears in the display. 3. Press the phone button.
SYNC™ (If Equipped) When you select: You can: Note: The system attempts to automatically re-download your phonebook and call history each time your phone connects to SYNC (if the auto download feature is on and your Bluetooth-enabled cellular phone supports this feature). Access and call any contacts in your previously downloaded phonebook. 1. Press OK to confirm and enter. If your phonebook has fewer than 255 listings, they appear alphabetically in flat file mode.
SYNC™ (If Equipped) Text Messaging Sending, Downloading and Deleting Your Text Messages Note: This is a phone-dependent feature. Note: Forwarding a text message is a speed-dependent feature and is only available when your vehicle is traveling at 3 mph (5 km/h) or less. SYNC allows you to receive, send, download and delete text messages. The system can also read incoming text messages to you so that you do not have to take your eyes off the road. Note: You can only have one recipient per text message.
SYNC™ (If Equipped) 3. Press OK when the desired selection is in the display. 4. Enter the name of the recipient. Scroll to cycle through Phonebook or Call History entries. You can also select Enter Number to say the desired number. 5. Press OK to enter the desired menu and scroll to select the specific contact. 6. Press OK when the contact appears and press OK again to confirm when the system asks if you would like to send the message.
SYNC™ (If Equipped) When you select: You can: If your phone supports in-band ringing, your phone's ring tone plays when you choose Phone Ringer. Message Notification Have the option of hearing an audible tone to notify you when a text message arrives. 1. Press OK to select and scroll between Message Notification On and Message Notification Off. 2. Press OK to select. Modify Phonebook Modify the contents of your phonebook (such as add, delete or download).
SYNC™ (If Equipped) 1. Press the phone button to enter the phone menu 2. Scroll to System Settings. Press OK. 3. Scroll to Bluetooth Devices. Press OK. 4. Scroll to select from the following options: If you select: You can: Add Bluetooth Device See Using SYNC™ With Your Phone (page 327). Connect Bluetooth Device Connect a previously paired Bluetooth-enabled phone. 1. Press OK to select and view a list of previously paired phones. 2.
SYNC™ (If Equipped) Advanced 1. Press the phone button to enter the phone menu 2. Scroll to System Settings. Press OK. 3. Scroll to Advanced. Press OK. 4. Scroll to select from the following options: The Advanced menu allows you to access and set prompts, languages, defaults, perform a master reset, install an application and view system information. If you select: You can: Prompts Get help from SYNC by using questions, helpful hints or asking you for a specific action.
SYNC™ (If Equipped) If you select: You can: Press OK to select. MAP Profile This is a Bluetooth component, which can further help your phone with the exchange of text messages. Return Exit the current menu. WARNINGS SYNC™ APPLICATIONS AND SERVICES (IF EQUIPPED) Do not wait for 911 Assist to make an emergency call if you can do it yourself. Dial emergency services immediately to avoid delayed response time which could increase the risk of serious injury or death after a crash.
SYNC™ (If Equipped) If a crash deploys an airbag (excluding knee airbags and rear inflatable safety belts [if equipped]) or activates the fuel pump shut-off, your SYNC-equipped vehicle may be able to contact emergency services by dialing 911 through a paired and connected Bluetooth-enabled phone. You can learn more about the 911 Assist feature, visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • • • • See Supplementary Restraints System (page 36).
SYNC™ (If Equipped) 911 Assist May Not Work If • • • Note: Your Vehicle Health Report feature requires activation before use. Visit www.SYNCMyRide.com to register. There is no fee or subscription associated with Vehicle Health Report, but you must register to use this feature. Your cellular phone or 911 Assist hardware sustains damage in a crash. The vehicle's battery or the SYNC system has no power. The phone(s) thrown from your vehicle are the ones paired and connected to the system.
SYNC™ (If Equipped) 1. Press the phone button to enter phone menu. 2. Scroll to select Vehicle Health, and then press OK. 3. Scroll to select from the following options: Vehicle health report options User Preferences: Press OK Automatic Reports: Press OK to and select On or Off. to select and enter the Select On to have SYNC automatically prompt you to run menu. Scroll to select from: a health report at certain mileage intervals.* Mileage Intervals: Press OK.
SYNC™ (If Equipped) Note: SYNC Services requires activation before use. Visit www.SYNCMyRide.com to register and check your eligibility for complimentary services. Standard phone and message rates may apply. Subscription may be required. You must also have the active SYNC Services Bluetooth-enabled cellular phone paired and connected to the system in order to connect to, and use, SYNC Services. See Using SYNC™ With Your Phone (page 327).
SYNC™ (If Equipped) Connecting to SYNC Services Using the Phone Menu 1. 2. 3. 4. 5. 6. assist you by searching for businesses by name or by category, residential addresses by street address or by name or specific street intersections. Operator Assist is a feature of your SYNC Services subscription. For more information on Operator Assist, visit www.SYNCMyRide.com/support. 2. Follow the voice prompts to select your destination.
SYNC™ (If Equipped) SYNC Services quick tips Personalizing You can personalize your Services feature to provide quicker access to your most used or favorite information. You can save address points such as work or home. You can also save favorite information like sports teams or a news category. You can learn more about personalization by logging onto www.SYNCMyRide.com.
SYNC™ (If Equipped) To Access Using the Media Menu 1. 2. 3. 4. 5. 6. 7. 8. USING SYNC™ WITH YOUR MEDIA PLAYER Press the AUX button on the center console. Press MENU to access the SYNC menu. Select "SYNC-Media" by pressing OK. Scroll to Mobile Apps and press OK to access a list of available applications. Scroll through the list of available applications and press OK to select a particular app.
SYNC™ (If Equipped) Press OK and scroll through selections of: • Play All • Albums • Genres • Playlists • Tracks • Explore USB • Similar Music • Return "USB" "Play playlist " 3 "Play previous folder" "Play previous track" "Play song " 1,2 1,2 "Play track " What's Playing? "Refine album " At any time when a track is playing, you can press the voice icon and ask the system "What's playing?". The system reads the metadata tags (if populated) of the playing track to you.
SYNC™ (If Equipped) 1 is a dynamic listing, meaning that it could be the name of anything, such as a group, artist or song. "USB" "Similar music" 2 This voice command is not available until indexing is complete. "What's playing?" 3 This voice command is only available in folder mode. Voice command guide "Autoplay" Turn autoplay on to listen to music processed during indexing. Turn autoplay off to allow the indexing process * to finish before the system plays any of your music.
SYNC™ (If Equipped) Media Menu Features and also to add, connect or delete devices. The media menu allows you to select your media source, how to play your music (such as by artist, genre, shuffle or repeat), 1. Press AUX and then MENU to enter the media menu. 2. Scroll to cycle through: When you select: You can: Play Menu Play your music by artist, album, genre, playlist, track, similar music or play all music.
SYNC™ (If Equipped) When you select: You can: System Settings Access Bluetooth Device menu listings (Add, Connect, Set as Primary, On and Off, Delete) as well as Advanced menu listings (prompts, languages, defaults, master reset, install application and system information). Exit Media Menu Press OK to exit the media menu. 1 The time required to complete this depends on the size of the media the system needs to index. If autoplay is on, you can listen to media processed during indexing.
SYNC™ (If Equipped) When you select: You can: 1. Press OK to select. You can select to play All Artists or any indexed artist. 2. Scroll to choose the desired artist. Press OK. Albums Sort all indexed media by albums. If there are fewer than 255 indexed albums, the system lists them alphabetically in flat file mode. If there are more than 255, the system categorizes them alphabetically. 1. Press OK to enter the album menu and select from playing all albums or from any individual indexed album. 2.
SYNC™ (If Equipped) When you select: You can: Press OK to select. The system creates a new list of similar songs and begins playing. This feature does not include tracks with incomplete metadata information. Return Exit the current menu. * With certain playing devices, if your metadata tags are not populated, the tracks are not available in voice recognition, play menu or similar music.
SYNC™ (If Equipped) When you select: You can: Press OK to select. Return * Exit the current menu. This is a speed-dependent feature. ** Setting Bluetooth to off disconnects all Bluetooth devices and turns off all Bluetooth features. 1. Press AUX and then MENU to enter the media menu. 2. Scroll to System Settings. Press OK. 3. Scroll to Advanced. Press OK. Advanced The Advanced menu allows you to access and set prompts, languages, defaults and perform a master reset.
SYNC™ (If Equipped) When you select: You can: Master Reset Completely erase all information stored on SYNC (all phonebook, call history, text messages and all paired devices) and return to the factory default settings. Application Download new software applications (if available) and then load the desired applications through your USB port. See the web site for more information. Return Exit the current menu.
SYNC™ (If Equipped) Phone issues Issue Possible cause(s) Possible solution(s) The system says Phonebook This may be a limitation on Downloaded but the your phone's capability. phonebook in SYNC is empty or missing contacts. · Try pushing your phonebook contacts to SYNC by using the Add Contacts feature. · If the missing contacts are stored on your SIM card, try moving them to the device memory. · Remove any pictures or special ring tones associated with the missing contact.
SYNC™ (If Equipped) USB and media issues Issue I am having trouble connecting my device. Possible cause(s) This may be a possible device malfunction. Possible solution(s) · Try turning off the device, resetting the device, removing the device's battery, then trying again. · Make sure you are using the manufacturer's cable. · Make sure you insert the USB cable properly into the device and the USB port. · Make sure that the device does not have an autoinstall program or active security settings.
SYNC™ (If Equipped) Vehicle Health Report and Services (Traffic, Directions and Information) issues Issue Possible cause(s) Possible solution(s) · Make sure that your VIN is correctly listed in your account. I am unable to retrieve the report on the website, or I receive a system error. The preferred dealer information did not load correctly. When you register your account, you must choose a preferred dealer. If it already lists a dealer, try selecting another dealer and logging out.
SYNC™ (If Equipped) Voice command issues Issue Possible cause(s) Possible solution(s) SYNC does not understand · You may be using the what I am saying. wrong voice commands. · You may be speaking too soon or at the wrong time. · Review the phone voice commands and the media voice commands at the beginning of their respective sections. · Be aware that SYNC's microphone is either in your rear view mirror or in the headliner just above the windshield.
SYNC™ (If Equipped) Voice command issues Issue Possible cause(s) Possible solution(s) · Your phonebook contacts may be in CAPS. · The system works better if you list full names, such as "Joe Wilson" rather than "Joe". · Do not use special characters, such as 123 or ICE, as the system does not recognize them. · If a contact is in CAPS, you have to spell it. JAKE requires you to say "Call JA-K-E".
MyFord Touch™ (If Equipped) GENERAL INFORMATION WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible.
MyFord Touch™ (If Equipped) This system uses a four-corner strategy to provide quick access to several vehicle features and settings. The touchscreen provides easy interaction with your cellular phone, multimedia, climate control and navigation system. The corners display any active modes within those menus, such as phone status or the climate temperature.
MyFord Touch™ (If Equipped) Using Your Bezel Controls Press to select any of the following: • AM • FM • SIRIUS • CD • USB • BT Stereo • SD Card • A/V In Depending on your vehicle and option package, you may also have these controls on your bezel: • Power: Switch the media or climate features off and on. • VOL: Control the volume of playing media. • Temperature, fan and climate control buttons: Control the temperature, fan speed or settings of the climate control system.
MyFord Touch™ (If Equipped) Monday-Saturday, 8:30am-9:00pm EST. • Sunday, 10:30am-7:30pm EST. In the United States, call: 1-800-392-3673. In Canada, call: 1-800-565-3673. • Times are subject to change due to holidays. Safety Information Make sure that you review your device's manual before using it with SYNC. WARNING Driving while distracted can result in loss of vehicle control, crash and injury.
MyFord Touch™ (If Equipped) Restricted features Editing settings while the rear view camera or active park assist are active Wi-Fi and Wireless Editing wireless settings Editing the list of wireless networks Videos, Photos and Graphics Playing video Editing the screen's wallpaper or adding new wallpaper Text Messages Composing text messages Viewing received text messages Editing preset text messages Navigation Using the keyboard to enter a destination Demo navigation route Adding or editing Address Bo
MyFord Touch™ (If Equipped) Using Voice Recognition What Can I Say? This system helps you control many features using voice commands. This allows you to keep your hands on the wheel and focus on what is in front of you. The system provides feedback through audible tones, prompts, questions and spoken confirmations depending on the situation and the chosen level of interaction (voice settings).
MyFord Touch™ (If Equipped) • Available voice commands "Audio list of commands" "Bluetooth audio list of commands" • "Browse list of commands" "CD list of commands" "Climate control list of commands" "List of commands" "Navigation list of commands" • * "Phone list of commands" "Radio list of commands" "SD card list of commands" "Sirius satellite list of commands" "Travel link list of commands" Interaction Mode: Novice mode provides detailed interaction and guidance while the advanced mode has less au
MyFord Touch™ (If Equipped) Using Voice Commands with the Touchscreen Options Voice settings using voice commands "Interaction mode novice" Your voice system has a dual mode feature which allows you to switch between using voice commands and making on-screen selections. This is available only when the system displays a list of candidates generated during a voice session. For example, when entering in a street address or trying to call a contact from the phone you paired to the system.
MyFord Touch™ (If Equipped) Under this menu, you can set your clock, access and adjust the display, sound and vehicle settings as well as access settings for specific modes or the help feature. • Clock • E142607 • Note: You cannot manually set the date. Your vehicle’s GPS does this for you. Note: If the battery has been disconnected, your vehicle needs to acquire a GPS signal to update the clock.
MyFord Touch™ (If Equipped) Only the photograph(s), which meets the following conditions, display: • Compatible file formats are as follows: .jpg, .gif, .png, .bmp • Each file must be 1.5 MB or less. • Recommended dimensions: 800 x 384 When done making your selections, press Run Vehicle Health Report Now if you want your report. You can find more information on Vehicle Health Report in this chapter. See Information (page 399).
MyFord Touch™ (If Equipped) Settings System Access and adjust system settings, voice features, as well as phone, navigation and wireless settings. E142607 Press the Settings icon > Settings > System, then select from the following: System Language Select to have the touchscreen display in English, Spanish or French. Distance Select to display units in kilometers or miles. Temperature Select to display units in Celsius or Fahrenheit.
MyFord Touch™ (If Equipped) Voice control Interaction Mode Standard interaction mode provides more detailed interaction and guidance. Advanced mode has less audible interaction and more tone prompts. Confirmation Prompts Have the system ask you short questions if it has not * clearly heard or understood your request. Media Candidate Lists Candidate lists are possible results from your voice commands. The system simply makes a best guess at your request with these turned off.
MyFord Touch™ (If Equipped) Media player Gracenote Database Info This allows you to view the version level of the Gracenote Database. Gracenote Mgmt With this feature on, the Gracenote Database supplies metadata information for your music files. This overrides information from your device. This feature defaults to off. Cover Art Priority With this feature on, the Gracenote Database supplied cover art for your music files. This overrides any art from your device. This feature defaults to Media Player.
MyFord Touch™ (If Equipped) Navigation Have the system automatically fill-in State/Province information. Traffic Preferences Have the system display areas where roadwork occurs. Have the system display incident icons. Have the system display areas where difficult driving conditions may occur. Have the system display areas where snow and ice on the road may occur. Have the system display any smog alerts. Have the system display weather warnings.
MyFord Touch™ (If Equipped) Phone Phone Ringer Select the type of notification for phone calls - ring tone, beep, text to speech, or have it be silent. Text Message Notification Select the type of notification for text messages - alert tone, beep, text to speech, or have it be silent. Internet Data Connection If compatible with your phone, you can adjust your internet data connection. Select to make your connection profile with the personal area network or to turn off your connection.
MyFord Touch™ (If Equipped) Wi-fi Wi-Fi Settings Wi-Fi Network (Client) Mode turns the Wi-Fi feature on and off in your vehicle. Make sure you turn it on for connectivity purposes. Choose a Wireless Network allows you to use a previously stored wireless network. You can categorize by alphabetical listing, priority and signal strength. You can also choose to search for a network, connect to a network, disconnect from a network, receive more information, prioritize a network or delete a network.
MyFord Touch™ (If Equipped) The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance. Help Press the Settings icon > Help, then select from the following: E142607 E142626 Help Where Am I? View your vehicle's current location, if your vehicle is equipped with navigation. If your vehicle is not equipped with navigation, you do not see this button.
MyFord Touch™ (If Equipped) To access Help using the voice commands, press the voice button, then, after the tone, say "Help". The system provides allowable voice commands for the current mode. ENTERTAINMENT A B G C D E H F E161892 A AM 1 and AM AST B FM 1, FM 2 and FM AST C SIRIUS D CD E USB F Touch this button to scroll down for more options, such as SD Card, BT Stereo and A/V In G These buttons change with the media mode you are in. H Radio memory presets and CD controls.
MyFord Touch™ (If Equipped) E142599 Press the voice icon on the steering wheel. When prompted, you can say: Your voice system allows you to change audio sources with a simple voice command. For example, if you are listening to music on a USB device, then want to switch to a satellite radio channel, simply press the voice button on the steering wheel controls and say the name of the SIRIUS station (such as, "the Highway").
MyFord Touch™ (If Equipped) Options Sample commands Sound Settings "Sirius <0-223>"* Touch this button to adjust settings for: "Sports games"* • • • • • • • * This command is only usable if you have an active subscription to SIRIUS satellite radio. ** The commands that have [ ] around the word means that the word is optional. For example, if you say, "Play Metallica", this is the same as the voice command, "Play [artist] ". Note: Your vehicle may not have all these sound settings.
MyFord Touch™ (If Equipped) Direct Tune The multicast indicator appears in FM mode (only) if the current station is broadcasting multiple digital broadcasts. The highlighted numbers signify available digital channels where new or different content is available. HD1 signifies the main programming status and is available in analog and digital broadcasts. Other multicast stations (HD2 through HD7) are only available digitally. Touch this button to manually enter the desired station number.
MyFord Touch™ (If Equipped) When HD Radio broadcasts are active, you can access the following functions: • Scan allows you to hear a brief sampling of all available stations. This feature still works when HD Radio reception is on, although it does not scan for HD2-HD7 channels. You may see the HD logo appear if the station has a digital broadcast. • Memory presets allow you to save an active channel as a memory preset. Touch and hold a memory preset slot until the sound returns.
MyFord Touch™ (If Equipped) Potential station issues Issues Echo, stutter, skip or repeat in audio. Increase or decrease in audio volume. Cause Action This is poor time alignment No action required. This is a by the radio broadcaster. broadcast issue. Sound fading or blending in The radio is shifting between No action required. The and out. analog and digital audio. reception issue may clear up as you continue to drive.
MyFord Touch™ (If Equipped) "RADIO" "RADIO" 3 "Tune" "<87.9-107.9>" "Help" 1 "<87.9-107.9> HD" 1 "<530-1710>" If available. 2 If you have said "Browse", see the "Browse" chart later in this section. "AM" 3 If you have said "Tune", see the following "Tune" chart. "AM <530-1710>" "AM autoset" "AM autoset preset <#>" "TUNE" "AM preset <#>" "<530-1710>" "Browse" "<87.9-107.9>" "FM" "<87.9-107.9> HD <#>" "FM <87.9-107.9>" "AM" 2 * "FM <87.9-107.
MyFord Touch™ (If Equipped) Scan "TUNE" Touch this button to hear a brief sampling of channels. * "HD <#>" "Preset <#>" Options "Help" * Touch this button to view and adjust various media settings. If available. Sound Settings SIRIUS® Satellite Radio (If Activated) E142611 Touch this button to adjust settings for: • • • • • • • Press the lower left corner of the touchscreen, and then select the SIRIUS tab. Memory Presets Save a channel by pressing and holding one of the memory preset areas.
MyFord Touch™ (If Equipped) Tune to the channel, to Cancel the alert or to Disable Alerts. If you are listening to a sporting event, you can save your favorite teams so that the system can alert you when they are playing on a satellite radio channel. E142593 Note: SIRIUS does not support the Alert feature on all channels. Ford Motor Company shall not be responsible for Alert feature variation.
MyFord Touch™ (If Equipped) SIRIUS Satellite Radio Reception Factors and Troubleshooting Potential reception issues Antenna obstructions For optimal reception performance, keep the antenna clear of snow and ice build-up and keep luggage and other materials as far away from the antenna as possible. Terrain Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception.
MyFord Touch™ (If Equipped) Troubleshooting tips Radio display Cause Action Updating. Update of channel programming in progress. No action required. The process may take up to three minutes. Call SIRIUS 1-888-539-7474. Your satellite service is no longer available. Contact SIRIUS at 1-888539-7474 to resolve subscription issues. None found. Check Channel All the channels in the Use the channel guide to Guide. selected category are either turn off the Lock or Skip skipped or locked.
MyFord Touch™ (If Equipped) Shuffle "SPORTS GAME" Touch this button to play the tracks or entire albums in random order, or turn the feature off if already on. "Tune to the game" "Tune to the game" Scan "Tune to the game" Touch this button to hear a brief sampling of all available tracks. "Tune to the game" More Info "Help" Touch this button to see disc information.
MyFord Touch™ (If Equipped) "CD" "Pause" "Play" "Play next track" "Play previous track" "Play track <1-512>" E142619 "Repeat" "Repeat folder" The SD card slot is located either in the center console or behind a small access door in the instrument panel. To access and play music from your device, press the lower left corner of the touchscreen. * "Repeat off" "Repeat track" "Shuffle" * "Shuffle CD" "Shuffle folder" * "Shuffle off" E142620 "Help" * SD logo is a trademark of SD-3C, LLC.
MyFord Touch™ (If Equipped) This feature allows you to plug in media playing devices, memory sticks, flash drives or thumb drives, and charge devices if they support this feature. In order to playback video from your iPod or iPhone, you must have a special combination USB/RCA composite video cable (which you can buy from Apple). When you connect the cable to your iPod or iPhone, plug the other end into both the RCA jacks and the USB port.
MyFord Touch™ (If Equipped) Playing Video from Your Device "USB" or "SD CARD" To access and play video from your device, your vehicle's transmission must be in position P with the ignition in accessory mode. See Starting and Stopping the Engine (page 132). "Play podcast " "Play podcast episode " "Play similar music" "Play song " SD Card and USB Voice Commands If you are listening to a USB device or an SD card, press the E142599 voice button on the steering wheel controls.
MyFord Touch™ (If Equipped) "BROWSE" "BROWSE" "TV show " "Album " * "All albums" "Video " "All artists" "Video playlist " "All audiobooks" * "Help" "All composers" * This command is only available in USB mode and is device-dependent. "All folders" "All genres" Supported Media Players, Formats and Metadata Information * "All movies" SYNC is capable of hosting nearly any digital media player, including iPod, Zune™, plays from device players, and most USB drives.
MyFord Touch™ (If Equipped) E142611 To access, press the lower left corner on the touchscreen, then select the BT Stereo tab. Bluetooth Audio Voice Commands If you are listening to a Bluetooth audio device, press the voice button on the steering wheel control. When prompted, say "Next song", "Pause", "Play" or "Previous song". E142599 E142622 If you are not listening to a Bluetooth audio device, press the voice button and, after the tone, say "Next song", "Pause", "Play" or "Previous song".
MyFord Touch™ (If Equipped) 3. Press the lower left corner on the touchscreen. Select either a tuned FM station or a CD (if there is a CD already loaded into the system). 4. Adjust the volume as desired. 5. Turn the portable music player on and adjust the volume to ½ the maximum. 6. Press the lower left corner on the touchscreen. Select the A/V In tab. (You should hear audio from your portable music player although it may be low.) 7.
MyFord Touch™ (If Equipped) A Phone B Quick Dial C Phonebook D History E Messaging F Settings Pairing Your Phone for the First Time Hands-free calling is one of the main features of SYNC. Once you pair your phone, you can access many options using the touchscreen or voice commands. While the system supports a variety of features, many are dependent on your cellular phone’s functionality. WARNING Driving while distracted can result in loss of vehicle control, crash and injury.
MyFord Touch™ (If Equipped) Note: Select SYNC, and a six-digit PIN appears on your device. SYNC may prompt you with more phone options. For more information on your phone's capability, see your phone's manual and visit the website. 3. If prompted to enter a PIN on your device, it does not support Secure Simple Pairing. To pair, enter the PIN displayed on the touchscreen. Skip the next step. 4.
MyFord Touch™ (If Equipped) • • Text Messaging Join two calls End the call. Note: Downloading and sending text messages using Bluetooth are phone-dependent features. Quick Dial Set up favorite contacts from your phonebook or history folder. Note: Certain features in text messaging are speed-dependent and not available when your vehicle is traveling at speeds over 3 mph (5 km/h). Phonebook Touch this button to access and call any contacts in your previously downloaded phone book.
MyFord Touch™ (If Equipped) • • Send, which sends the message as it is. Edit Text, which allows you to customize the pre-defined message or create a message on your own. When a new message arrives, an audible tone sounds and the screen displays a pop-up with the caller name and ID, if supported by your phone. You can press: • View to view the text message. • Listen for SYNC to read the message to you. • Dial to call the contact. • Ignore to exit the screen.
MyFord Touch™ (If Equipped) Text Message Notification "PHONE" Select a text message notification, if supported by your phone. Choose from possible system alert tones, text-to-speech or silent. "Call on other" "Call voicemail" "Dial" Internet Data Connection "Do not disturb off" If your phone is compatible, use this screen to adjust your internet data connection. Select to make your connection profile with the personal area network or to turn off your connection.
MyFord Touch™ (If Equipped) "PHONE" "MESSAGES" "Unmute call" * "Call" "Help" "Forward text messages" * This command is only available during an active call. "Listen to text message <#>" "Listen to text messages" ** If you say "Messages", see the following "Messages" chart for additional commands.
MyFord Touch™ (If Equipped) Under the Information menu, you can access features such as: • SYNC Services • Sirius Travel Link • Alerts • Calendar • SYNC Applications If your vehicle is equipped with Navigation, press the Information button to access these features. If your vehicle is not equipped with Navigation, press the corner of the touchscreen with the green tab.
MyFord Touch™ (If Equipped) 1. Press the voice button. 2. When prompted, say "Services". This initiates an outgoing call to SYNC Services using your paired and connected Bluetooth-enabled cellular phone. 3. Once you connect to the service, follow the voice prompts to request the desired service, such as "Traffic" or "Directions". You can also say, "What are my choices?" to receive a list of available services from which to choose. 4.
MyFord Touch™ (If Equipped) Disconnecting from SYNC Services 1. button on the steering wheel. 2. Say "Good-bye" from the SYNC Services main menu. Press and hold the hang-up phone SYNC Services quick tips Personalizing You can personalize your Services feature to provide quicker access to your most used or favorite information. You can save address points, such as work or home. You can also save favorite information like sports teams, such as Detroit Lions, or a news category.
MyFord Touch™ (If Equipped) Note: In order to use Sirius Travel Link, your vehicle must be equipped with navigation and your navigation SD card must be in the SD card slot. Weather Touch this button to view the nearby weather, current weather, or the five day forecast for the chosen area. Select Map to see the weather map, which can show storms, radar information, charts and winds. Select Area to select from a listing of weather locations.
MyFord Touch™ (If Equipped) "SIRIUS TRAVEL LINK" Additional sports-related voice commands "Weather map" "College football schedule" "Help" "College football scores" * If you say "Sports headlines", "Sports schedules" or "Sports scores", you can then say any of the commands in the following chart.
MyFord Touch™ (If Equipped) 911 Assist (If Equipped) Additional sports-related voice commands WARNINGS Unless the 911 Assist setting is set on before a crash, the system will not dial for help, which could delay response time, potentially increasing the risk of serious injury or death after a crash. "WNBA schedule" "WNBA scores" "Help" Do not wait for 911 Assist to make an emergency call if you can do it yourself.
MyFord Touch™ (If Equipped) If a crash deploys an airbag (excludes knee airbags and rear inflatable safety belts [if equipped]) or activates the fuel pump shut-off, your SYNC-equipped vehicle may be able to contact emergency services by dialing 911 through a paired and connected Bluetooth-enabled phone. You can learn more about the 911 Assist feature, visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • • • • See Supplementary Restraints System (page 36).
MyFord Touch™ (If Equipped) 911 Assist May Not Work If • • • Note: Your Vehicle Health Report feature requires activation prior to use. Visit www.SYNCMyRide.com to register. There is no fee or subscription associated with Vehicle Health Report, but you must register to use this feature. Your cellular phone or 911 Assist hardware sustains damage in a crash. The vehicle's battery or the SYNC system has no power. The phone(s) thrown from your vehicle are the ones paired and connected to the system.
MyFord Touch™ (If Equipped) To run a report by voice command, press the voice button on the steering wheel and, when prompted, say "Vehicle health report". information, do not run the feature or set up your Vehicle Health Report profile at www.SYNCMyRide.com. See www.SYNCMyRide.com (Vehicle Health Report Terms and Conditions, and Privacy Statement) for more information.
MyFord Touch™ (If Equipped) Touch DUAL to turn separate passenger side temperature controls off and on. When you turn off DUAL, the passenger side temperature changes to match the driver side temperature. Note: The passenger side temperature and the DUAL indicator automatically turn on when the passenger is adjusting their temperature control. C Fan speed: Touch + or - to increase or decrease the volume of air circulated in your vehicle.
MyFord Touch™ (If Equipped) Touch the climate-controlled seat icon to turn the climate-controlled seat off and on (if equipped). Touch MyTemp to select your preset temperature setpoint. Touch and hold MyTemp to save a new preset temperature setpoint. Touch the heated steering wheel icon to turn the heated steering wheel on and off (if equipped). Note: If your vehicle is equipped with a wood-trimmed steering wheel, it does not heat between the 10 o'clock and 2 o'clock positions.
MyFord Touch™ (If Equipped) To view the navigation map and your vehicle's current location, touch the green bar in the upper right hand corner of the touchscreen, or, press Dest, then Map. See Map mode later in this chapter. "CLIMATE" "Temperature increase" "Temperature low" "Windshield floor on" Setting a Destination "Help" Press the green corner of your touchscreen, then the Dest button when it appears.
MyFord Touch™ (If Equipped) 2. Select Set as Dest to make this your destination. You can also choose to set this as a waypoint (have the system route to this point on the way to your current destination) or save it as a favorite. The system considers any Avoid Areas selections in its route calculation. 3. Choose from up to three different types of routes, and then select Start Route. • Fastest: Uses the fastest moving roads possible. • Shortest: Uses the shortest distance possible.
MyFord Touch™ (If Equipped) The system also allows you to sort alphabetically, by distance or by cityseekr listings (if available). Food & Drink E142637 cityseekr Nightlife Note: cityseekr point of interest (POI) information is limited to approximately 912 cities (881 in the United States, 20 in Canada and 11 in Mexico). E142638 Attraction E142639 This icon appears when your selection exists in multiple categories within the system.
MyFord Touch™ (If Equipped) Eco Time Penalty Setting Your Navigation Preferences Select a low, medium or high cost for the calculated Eco Route. The higher the setting, the longer the time allotment is for the route. Select settings for the system to take into account when planning your route. Press the Settings icon > Settings > Navigation. Avoid E142607 These features allow you to choose to have the system avoid freeways, toll roads, ferries and car trains when planning your route.
MyFord Touch™ (If Equipped) Traffic Alert Notification Have the system display traffic alert notifications. Other traffic alert features allows you to turn on certain, or all, traffic icons on the map such as road work, incident, accidents and closed roads. Scroll down to view all the different types of alerts. Turn these features ON or OFF. Avoid Areas E174016 Change the appearance of the map display by repeatedly pressing the arrow button in the upper left corner of the screen.
MyFord Touch™ (If Equipped) Press the speaker button on the map to mute route guidance. E174017 When the light on the button illuminates, the feature is on. The speaker button appears on the map only when route guidance is active. Scroll cursor allows you to scroll the map; the fixed icon is in the center of the screen. The map E142647 position closest to the cursor is in a window on the top center part of the screen.
MyFord Touch™ (If Equipped) No GPS symbol indicates that insufficient GPS satellite signals are available for accurate map E142655 positioning. This icon may display under normal operation in an area with poor GPS access. • • • • • Edit Turn List Detour Edit Route Preferences Edit Traffic Preferences Cancel Route. Nokia is the digital map provider for the navigation application. If you find map data errors, you may report them directly to Nokia by going to http://mapreporter.navteq.com.
MyFord Touch™ (If Equipped) Navigation system voice commands Navigation system voice commands "Destination intersection" "Zoom out" "Destination nearest " "Help" 1 "Destination nearest POI" These commands are only available when a navigation route is active. "Destination play nametags" 2 If you say "Destination", you can then say any command in the following "Destination" chart.
MyFord Touch™ (If Equipped) "NAVIGATION" "Zoom maximum" "Zoom province" "Zoom state" "Zoom street" "Zoom to " "Help" * If you say "Destination", you can then say any command in the "Destination" chart. One-shot Destination Street Address When you say either "Navigation destination street address" or "Destination street address", the system asks you to say the full address. The system displays an example on-screen.
Accessories Lifestyle For a complete listing of the accessories that are available for your vehicle, please contact an authorized dealer or visit our online store at www.Accessories.Ford.com (United States only). • • • • • Ford Motor Company will repair or replace any properly authorized dealer-installed Ford Genuine Accessories found to be defective in factory-supplied materials or workmanship during the warranty period, as well as any component damaged by the defective accessories.
Accessories For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety Compliance Certification label). Ask an authorized dealer for specific weight information.
Accessories E167344 E167343 There will also be one power lead for each switch found as a blunt-cut and sealed wire located to the right of the glove box door and just above the passenger side kick panel. You may need to pull down the auxiliary cords to access them. Refer to the Fuses chapter of your Owner’s Manual for information on fuse and relay locations. See your authorized dealer for service.
Appendices • END USER LICENSE AGREEMENT SYNC® End User License Agreement (EULA) • • You have acquired a device ("DEVICE") that includes software licensed by Ford Motor Company and its affiliates ("FORD MOTOR COMPANY") from an affiliate of Microsoft Corporation ("MS") . Those installed software products of MS origin, as well as associated media, printed materials, and "online" or electronic documentation ("MS SOFTWARE") are protected by international intellectual property laws and treaties.
Appendices Description of Other Rights and Limitations • • • • • Speech Recognition: If the SOFTWARE includes speech recognition component(s), you should understand that speech recognition is an inherently statistical process and that recognition errors are inherent in the process. Neither FORD MOTOR COMPANY nor its suppliers shall be liable for any damages arising out of errors in the speech recognition process.
Appendices • • • Consent to Use of Data: You agree that MS, Microsoft Corporation, FORD MOTOR COMPANY, third party software and systems suppliers, their affiliates and/or their designated agent may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE or related services.
Appendices • • Links to Third Party Sites: The MS SOFTWARE may provide you with the ability to link to third party sites through the use of the SOFTWARE. The third party sites are not under the control of MS, Microsoft Corporation, their affiliates and/or their designated agent.
Appendices Adobe TRADEMARKS: This EULA does not grant you any rights in connection with any trademarks or service marks of FORD MOTOR COMPANY, MS, Microsoft Corporation, third party software or service providers, their affiliates or suppliers. Contains Adobe® [Flash® Player] or [AIR®] technology by Adobe Systems Incorporated. This [Licensee Product] contains [Adobe® Flash® Player] [Adobe® AIR®] software under license from Adobe Systems Incorporated, Copyright ©1995-2009 Adobe Macromedia Software LLC.
Appendices Use of Speech Recognition Functions: Speech recognition software is inherently a statistical process which is subject to errors. It is your responsibility to monitor any speech recognition functions included in the system and address any errors. WARNING Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences.
Appendices Potential Map Inaccuracy: Maps used by this system may be inaccurate because of changes in roads, traffic controls or driving conditions. Always use good judgment and common sense when following the suggested routes. Telenav may revise this Agreement and the privacy policy at any time, with or without notice to you. You agree to visit http://www.telenav.com from time to time to review the then current version of this Agreement and of the privacy policy.
Appendices 2.
Appendices COURSE OF DEALING, CUSTOM OR TRADE AND INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS WITH RESPECT TO THE TELENAV SOFTWARE. Certain jurisdictions do not permit the disclaimer of certain warranties, so this limitation may not apply to you.
Appendices the terms and conditions of this Agreement. Any such sale, assignment or transfer that is not expressly permitted under this paragraph will result in immediate termination of this Agreement, without liability to Telenav, in which case you and all other parties shall immediately cease all use of the Telenav Software. Notwithstanding the foregoing, Telenav may assign this Agreement to any other party at any time without notice, provided the assignee remains bound by this Agreement.
Appendices Agreement), and thus your use of the Telenav Software is also subject to such terms. You agree to comply with the following additional terms and conditions, which are applicable to Telenav’s third party vendor licensors: TERMS AND CONDITIONS License Limitations on Use: You agree that your license to use this Data is limited to and conditioned on use for solely personal, noncommercial purposes, and not for service bureau, timesharing or other similar purposes.
Appendices Disclaimer of Liability: real time route guidance, fleet management or similar applications; or (b) with, or in communication with, including without limitation, cellular phones, palmtop and handheld computers, pagers, and personal digital -assistants or PDAs. This Data is provided to you “as is”, and you agree to use it at your own risk.
Appendices Entire Agreement: Government End Users: These terms and conditions constitute the entire agreement between HERE (and its licensors, including their licensors and suppliers) and you pertaining to the subject matter hereof, and supersedes in their entirety any and all written or oral agreements previously existing between us with respect to such subject matter.
Appendices Gracenote® Copyright You agree that you will use the content from Gracenote ("Gracenote Content") , Gracenote Data, the Gracenote Software, and Gracenote Servers for your own personal, non-commercial use only. You agree not to assign, copy, transfer or transmit the Gracenote Content, Gracenote Software or any Gracenote Data (except in a Tag associated with a music file) to any third party.
Appendices THE GRACENOTE SOFTWARE, EACH ITEM OF GRACENOTE DATA AND THE GRACENOTE CONTENT ARE LICENSED TO YOU "AS IS". NEITHER GRACENOTE MAKES ANY REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, REGARDING THE ACCURACY OF ANY GRACENOTE DATA FROM THE GRACENOTE SERVERS OR GRACENOTE CONTENT.
Extended Service Plan (ESP) PROTECT YOURSELF FROM THE RISING COST OF VEHICLE REPAIRS WITH A FORD EXTENDED SERVICE PLAN. That means you get: • Reliable, quality service at any Ford or Lincoln dealership • Repairs performed by factory trained technicians, using genuine parts SERVICE PLANS (U.S. Only) More than 32 million Ford owners have discovered the powerful protection of Ford Extended Service Plan.
Extended Service Plan (ESP) SERVICE PLANS (CANADA ONLY) Avoid the Rising Cost of Properly Maintaining Your Vehicle! You can get more protection for your vehicle by purchasing a Ford Extended Service Plan. Ford Extended Service Plan is the only service contract backed by Ford Motor Company of Canada, Limited.
Scheduled Maintenance Genuine Ford and Motorcraft Replacement Parts GENERAL MAINTENANCE INFORMATION Dealerships stock Ford, Motorcraft and Ford-authorized branded re-manufactured replacement parts. These parts meet or exceed our specifications. Parts installed at your dealership carry a nationwide 24-month or unlimited mile (kilometer) parts and labor limited warranty.
Scheduled Maintenance Ford Motor Company has recommended maintenance intervals for various parts and component systems based upon engineering testing. Ford Motor Company relies upon this testing to determine the most appropriate mileage for replacement of oils and fluids to protect your vehicle at the lowest overall cost to you and recommends against maintenance schedules that deviate from the scheduled maintenance information.
Scheduled Maintenance Check every six months Hinges, latches and outside locks for proper operation. Lubricate if necessary. Parking brake for proper operation. Safety belts and seat latches for wear and function. Safety warning lamps (brake, ABS, airbag and safety belt) for operation. Washer spray and wiper operation. Clean or replace blades as necessary. Multi-point Inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly.
Scheduled Maintenance Be sure to ask your dealership service advisor or technician about the multi-point vehicle inspection. It is a comprehensive way to perform a thorough inspection of your vehicle. Your checklist gives you immediate feedback on the overall condition of your vehicle. NORMAL SCHEDULED MAINTENANCE 6.2L and 6.8L Gasoline Engines Every 7500 miles (12000 km) or six months (whichever comes first) Change engine oil and filter. * Rotate tires , inspect tire wear and measure tread depth.
Scheduled Maintenance Other maintenance items Replace front wheel bearing grease and grease seal if nonsealed bearings are used. Every 97500 miles (156000 Replace spark plugs. km) ** Change engine coolant. Every 105000 miles (168000 km) Replace rear axle fluid. Inspect accessory drive belt(s). *** Change automatic transmission fluid and filter on 6-speed transmission. Consult dealer for requirements.
Scheduled Maintenance Towing a trailer or using a car-top carrier Inspect frequently, service as required Inspect and lubricate U-joints. Every 5000 miles (8000 km) Inspect the wheels and related components for abnormal noise, wear, looseness or drag. See axle maintenance items under Exceptions. * Rotate tires , inspect tires for wear and measure tread depth. Every 5000 miles (8000 km) or six months Change engine oil and filter. Inspect and lubricate U-joints.
Scheduled Maintenance Extensive idling or low-speed driving for long distances, as in heavy commercial use (such as delivery, taxi, patrol car or livery) Every 30000 miles (48000 Change transfer case fluid (Four-wheel drive vehicles). km) Replace front wheel bearing grease and grease seals if non-sealed bearings are used. Every 60000 miles (96000 Replace spark plugs. km) * Vehicles with dual rear wheels should rotate the front wheels when specified; rear wheels only if unusual wear is noted.
Scheduled Maintenance Off-road operation Inspect frequently, service as required Inspect steering linkage, ball joints and U-joints, Lubricate if equipped with grease fittings. Replace engine air filter. Every 5000 miles (8000 km) or six months Change engine oil and filter. Inspect the wheels and related components for abnormal noise, wear, looseness or drag. * Rotate tires , inspect tires for wear and measure tread depth.
Scheduled Maintenance Ford specification WSL-M2C192-A, part number F1TZ-19580-B, or equivalent. Add friction modifier XL-3 (EST-M2C118-A) or equivalent for complete refill of Traction-Lok rear axles. See Capacities and Specifications (page 301). If the available API SM or SN oils are not available, then the oil change interval is 1800 miles (3000 kilometers).
Scheduled Maintenance SCHEDULED MAINTENANCE RECORD Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 449 Super Duty (), enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 450 Super Duty (), enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 451 Super Duty (), enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 452 Super Duty (), enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 453 Super Duty (), enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 454 Super Duty (), enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 455 Super Duty (), enUSA
456 Super Duty (), enUSA
Index 4 Audio unit - Vehicles With: AM/FM/CD/ SYNC..............................................................312 Audio unit - Vehicles With: AM/FM.........311 Audio unit - Vehicles With: Sony AM/FM/ CD....................................................................315 Autolamps........................................................65 4WD See: Four-Wheel Drive.......................................151 A Autolamps - Programmable Exit Delay..........................................................
Index Center Console...............................................131 Cleaning the Exterior..................................256 Removable Front Cupholders.........................131 Cleaning Plastic Exterior Parts......................257 Exterior Chrome.................................................256 Stripes or Graphics (if equipped)................256 Underbody............................................................257 Changing a Bulb..........................................
Index DRL Essential Towing Checks...........................193 See: Daytime Running Lamps........................66 Before Towing a Trailer....................................203 Dynamic Hitching Using the Rear View Camera System.............................................194 Hitches....................................................................195 Integrated Trailer Brake Controller..............198 Launching or Retrieving a Boat or Personal Watercraft (PWC).......................................
Index H Fuel and Refueling.......................................136 Fuel Consumption.......................................140 Calculating Fuel Economy..............................140 Filling the Tank....................................................140 Handbrake See: Parking Brake.............................................163 Fuel Filter........................................................244 Fuel Quality.....................................................137 Hazard Warning Flashers.........
Index J Information....................................................399 911 Assist..............................................................405 Alerts......................................................................405 Calendar...............................................................405 Sirius Travel Link................................................402 SYNC Services (If Equipped, United States Only).................................................................
Index Manual Seats..................................................112 Overhead Console.........................................131 Manual Lumbar ...................................................113 Moving the Seat Backward and Forward...............................................................112 Recline Adjustment.............................................112 P Parking Aid.......................................................172 Media Hub......................................................
Index Rear Seats........................................................114 Roadside Emergencies...............................212 Running-In Folding the Rear Seat Back (Crew Cab) ...............................................................................115 Folding up the Rear Seat Cushion.................115 Rear Under Seat Storage (Crew Cab).........116 Returning the Seat to the Seating Position...............................................................115 See: Breaking-In.....................
Index Special Notices................................................12 SYNC™ Applications and Services........................................................338 New Vehicle Limited Warranty.........................12 Special Instructions..............................................12 Using your Vehicle as an Ambulance.............13 Using your Vehicle as a Stationary Power Source...................................................................13 Using your Vehicle with a Snowplow.............
Index Towing..............................................................189 Traction Control............................................165 Using SYNC™ With Your Media Player............................................................345 Principle of Operation.......................................165 See: Transmission..............................................144 Accessing Your Play Menu.............................349 Connecting Your Digital Media Player to the USB Port...........................
Index Ventilation Windshield Wipers........................................64 See: Climate Control.........................................103 Speed dependent wipers.................................64 VIN Wipers and Washers.....................................64 See: Vehicle Identification Number............303 Voice Control....................................................61 W Warning Lamps and Indicators..................77 4X2.....................................................................
