G5103_2008-06F.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page i Limited lifetime consumer warranty For a period of one calendar year from the date of purchase of this auto-security device, Directed Electronics, Inc.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page ii ING, REPAIR, REPLACEMENT, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 1 Table of contents Limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Standard transmitter configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 What is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 2 Rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 3 Standard transmitter configuration controls the Arm and Panic On/Off function. controls the Disarm and Panic Off function. controls Silent Mode™ and Auxiliary trunk output. controls the Remote Start function. and pressed together control the Timer mode. and pressed together control Turbo/Short Run. and pressed together control auxillary 4 output. and pressed together control auxillary 5 output.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 4 control Temperature check. and and and controls Daily start on/off. and and controls Temperature start on/off.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 5 warranty. All dealers are provided with a preprinted dealer certificate to verify authorization. By carefully reading this Owner's Guide prior to using your system, you will maximize the use of this system and its features. You can print additional or replacement copies of this manual by accessing our web site at www.directed.com. ➜ System maintenance The system requires no specific maintenance.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 6 interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. ➜ Caution This product is designed for fuel injected, automatic transmission vehicles only. Use of this product in a standard transmission vehicle is dangerous and contrary the product's intended use.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 7 Button The disarming function is controlled by pressing this button for one second. Button Silent Mode™ and an optional auxiliary function are controlled by this button. (Silent Mode works by pressing this button for less than one second before arming or disarming. An optional auxiliary function, such as trunk release, can be controlled by pressing this button for 1.5 seconds.) The auxiliary output controls __________________________.
G5103_2008-06F.qxd and 7/9/2008 10:39 AM Page 8 Buttons The remote start timer mode is controlled by pressing these buttons simultaneously. The 2-way remote produces a melody and the clock indicator appears on the remote's LCD. Once in timer mode the system remote starts every 24-hours. Repeat this procedure to turn Timer Mode off. and Buttons The short-run turbo mode is activated when these buttons are pressed simultaneously.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 9 Note: If the ignition is on, the temperature check clockmode will not work. and Buttons While the system is armed, press simulataneously to enter temperature auto statt mode. The vehicle is automatically restarted if the interior temperature drops below 0 degrees Fahrenheit. Note: Disarming the system while in temperature autostart mode casuses the system to exit this mode.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 10 must be disabled using the installed toggle switch. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 11 product installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear. All installations must be performed by an authorized Directed dealer.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 12 the status LED is flashing in groups, see the Diagnostics Section of this guide. This extra chirp is called Bypass Notification. ➜ Passive arming The system can be programmed to arm itself automatically (called passive arming). If the system is programmed for passive arming, it will automatically arm 30 seconds after the ignition is turned off and the system detects that you have left the vehicle by opening and closing a door.
G5103_2008-06F.qxd ➤ ➤ ➤ 7/9/2008 10:39 AM Page 13 If a door is opened, the system will immediately start chirping the siren and flashing the parking lights. Three seconds later, the siren output changes to a continuous blast. This progressive response gives you time to disarm the system with your transmitter if you inadvertently open the door while the system is armed, while still providing instant response (even if the door is immediately closed).
G5103_2008-06F.qxd ➤ Press 7/9/2008 10:39 AM Page 14 a fifth time within five seconds: The siren chirps five times followed by a long chirp. All input zones, except the ignition, are now bypassed. Note: Multi-Level Security Arming only applies to a single arming cycle. Once the system is disarmed and then re-armed, all the zones will be active again.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 15 ➜ Disarming To disarm the security system, press . You will hear two chirps, and the parking lights will flash twice. If the power locks are controlled by the system, the doors will also unlock. The siren chirping either four or five times when disarming indicates Tamper Alert, which is described in the Diagnostics Section of this guide. ➜ High security disarm This security system offers High Security Disarm.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 16 and know where the Valet® switch is located. Be sure to check with your installer at the time of installation for both the location and the preset response (1-5 presses) of the Valet® switch. To disarm the security system, turn the ignition to the ON position. Press the Valet button the preset number of times (one to DRW-35 five times) within 15 seconds. After five seconds, the system will disarm.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 17 Note: The Warn Away® response to lighter impacts is bypassed if the system is armed using Silent Mode. This ensures that no chirps will be emitted by the siren in an area you want chirp-free. The system is still fully capable of triggering. Only the Warn Away® response is bypassed. ➜ Panic mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 18 The status LED will light solidly if you are entering Valet Mode, and it will go out if you are exiting Valet Mode. To enter or exit Valet Mode using the transmitter: 1. Open any vehicle door. 2. Press . 3. Press . 4. Press again. The status LED will light solidly if you are entering Valet Mode, and it will go out if you are exiting Valet Mode.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 19 3. In gasoline vehicles, the engine starts 4 seconds after the parking lights flash. In diesel vehicles, the engine starts when the WAIT-TO-START indicator on the vehicle's dash goes out or the programmed delay has ended. 4. Once the vehicle has started, it runs for the pre-programmed period of time (either 12, 24, or 60 minutes - see Programming Options section of this guide) or until a shutdown input is triggered.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 20 ➤ The shutdown toggle switch is put into the OFF position. ➤ The pre-programmed run time (12, 24, or 60 minutes) has elapsed. ➤ Transmitter buttons is pressed twice within 3 seconds. ➜ Rear defogger To turn the rear defogger output OFF: 1. Simultaneously press & release the + + buttons on the remote control. 2. The lights will flash 2 times. 3. The rear defogger output will no longer activate when the vehicle is remote started.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 21 Note: If the temperature is greater than 55° F at the time of remote start activation, the rear defogger will not activate for that start. ➜ Valet take-over The Valet Take-Over feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate controls on.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 22 down the turbo after you have left the vehicle. To activate: 1. Park the vehicle and set parking brake. 2. Remove your foot from the brake pedal and leave the engine running. 3. Press and release the and buttons at the same time. 4. The lights will flash to indicate the remote start has entered short run turbo mode. 5. Turn off the key, the engine will keep running. 6. Exit and secure the vehicle. 7.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 23 circuitry prevents the starter from engaging, even if the key is turned to the start position. This prevents damage to the starter motor if the key is turned to the start position during remote start operation. ➜ Disabling the remote start system This feature allows your system's remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 24 ➜ Nuisance prevention® circuitry Your system has Directed’s Nuisance Prevention® Circuitry (NPC). It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder, jackhammers, airport noise, etc. Example If the alarm triggers three times within a 60-minute period and each time the same sensor or switch triggers the alarm, NPC will interpret those triggers as false alarms.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 25 Diagnostics The microprocessor at the heart of your system is constantly monitoring all of the switches and sensors connected to it. It is designed to detect any faulty switches and sensors and prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred during your absence. Refer to the System Status Chirps and Table of Zones sections of this guide for diagnostic information.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 26 ➜ Disarming diagnostics Extra chirps that are heard when disarming the system are the Tamper Alert. If four chirps are heard when disarming the system, then the security system was triggered in your absence. If five chirps are heard when disarming the system, a zone was triggered so many times that the Nuisance Protection® Circuitry has bypassed that zone. In either case, the status LED will indicate which zone was involved (see Table of Zones section).
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 27 ➜ Table of zones A zone is represented by the number of LED flashes used by the system to identify a particular type of input. Standard input assignments are listed in the following table, along with spaces to write in any optional sensors or switches that have been installed.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 28 Note: Your system stores the last two triggered zones in memory. If your system has been triggered but the LED has been reset by turning on the ignition, your dealer can still recall the last two zones that were triggered. Contact your dealer for details. Code hopping The receiver and transmitters use a mathematical formula called an algorithm to change their code each time the transmitter is used.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 29 radio interference. Owner recognition Owner Recognition is a revolutionary new feature available only from Directed. Using a Directed Bitwriter®, hand-held programming tool, your dealer can program many of the system settings. The programmer makes it possible to program different settings for each transmitter that is used with the system. Then, whenever a specific transmitter is used, the system will recall the settings assigned to that transmitter.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 30 still be in Valet Mode. This applies to all states of the system including arm, disarm, and Valet Mode. Power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode, after a period of time in which no operation has been performed. This lowers the current draw on the vehicle's battery.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 31 The following is a list of the programmable options, with the factory settings in Bold. ➤ Active arming (transmitter only) or passive arming (automatic arming 30 seconds after the last door has been closed). ➤ Arming/disarming siren chirps on or off. ➤ The ignition controlled door lock feature on or off: When this feature is programmed on, the doors will lock three seconds after the ignition is turned on, and unlock when the ignition is turned off.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 32 Note: When the system passively arms after one hour, the entry point that has been left open, and anything connected to the same zone, is bypassed and cannot trigger the system. However, the remaining inputs to the system are fully operational. ➤ Full trigger response 30 or 60 seconds: This determines how long the full triggered sequence lasts. Some states have laws regulating how long a security system can sound before it is considered a nuisance.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 33 minutes when remote started in timer mode. Can be set up to 16 minutes by your installer. ➤ While the remote start system is running the engine, the parking lights of the vehicle can flash on and off or come on and light steadily. ➤ Comfort closure is a programming option which closes the vehicle’s windows after remote locking. Security & convenience expansions Listed below are some of the many expansion options available.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 34 Power Trunk Release: The accessory output of the system can op- erate a factory power release for the vehicle’s trunk or hatch. Although the on-board relay can control most power trunk releases, sometimes an optional relay is required. If the factory release is not power-activated, Directed®'s 522T trunk release solenoid can often be added. Power Window Control: Automatic power window control is pro- vided with the 529T and 530T systems.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 35 Glossary of terms Control Unit: The “brain” of your system. Usually hidden under- neath the dash area of the vehicle. The control unit houses the microprocessor which monitors your vehicle and controls all system functions. Input: A physical connection to the system. An input can be provided by a sensor, pinswitch or by existing systems in the vehicle, such as ignition or courtesy lights.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 36 Warning Zone Response: Lighter impacts to the vehicle will generate the Warning Zone response. It consists of several Zone: A zone is a separate input that the alarm can recognize as ll seconds of siren chirps and parking light flashes. unique. Each input to the system is connected to a particular l d d li d f ld f i k d f k i zone. Often two or more inputs may share the same zone.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 37 ✂ Quick reference guide Arming Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet. ■ To arm, press . When the system arms, you will hear a short chirp, and the parking lights will flash once. Arming while driving ■ To arm the system while driving, press on your transmitter while the vehicle is running. The system will chirp once and then once more to indicate that the ignition is on.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 38 ✂ Location of Valet button_________________________________ Number of Valet button pulses for disarming_______________ Valet Takeover Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet. ■ Press and release on the transmitter twice in 3 seconds. Turn the ignition key to the OFF position. Once the vehicle has started, it will run for the pre-programmed period of time (12, 24, or 60 minutes).
Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet. G5103_2008-06F.
G5103_2008-06F.qxd 7/9/2008 10:39 AM Page 42 The company behind this system is Directed Electronics Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, Directed is ISO 9001 registered.
