Quick Start Guide

ManualsBrandsAvycon ManualsNVR32 Channels 4K UHD Network Video Recorder, 30TB

Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.

All the examples and pictures used here are for reference only. There may be several technically incorrect places

or printing errors in this manual. The updates will be added into the new version of this manual. The contents of

this manual are subject to change without notice.This device should be operated only from the type of power

source indicatedon the marking label. The voltage of the power must be veriﬁed before using the same.

Network Video Recorder

Quick Start Guide

This series of the product supports 8 SATA hard drives. Please make

sure that the device is powered off before the installation.

4. Connect the power and data cables and install the other three HDDs according

to above-mentioned method.

5. Screw the longer pillar into the lower mounting bar.

6.Install back the upper mounting bar and tighten the screw of the pillar.

7. Install the upper four HDDs and install back the cover.

Please check the device and the accessories after getting the device.

If there are any damages, shortages or defects, please contact your

dealer immediately.

For our HN500 series NVRs, the default username is admin and the

default password is 123456. When starting HN500 series NVR for

the ﬁrst time, you will see a prompt to begin a startup wizard. You can

skip this wizard if you would like, but it will help you conﬁgure basic

settings for your NVR. The wizard may allow you to also change the

default password for better security. If you decide to skip the wizard,

to access the live view and start using your NVR click on the Start

button in the bottom left of the menu bar on the bottom of the

screen and then click on Login and enter in the default password.

2. HDD Installation

1. Packing Check

3. Rear Panel Installation

The interfaces of the rear panel are for reference only.

• Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

• Shutdown

Go to “Main Menu” and then select “Shutdown” icon. This will bring

up a shutdown window. The device will shut down by clicking “OK”

button. Then disconnect the power.

4. Startup & Shutdown

4. Login

Username

Password

admin

Enter Password

Display Password Log In Automatically

LoginEdit Security Question Cancel

After you ﬁnish adding IP cameras, you can see the live images through

the monitor of the NVR. The following will mainly introduce how to add

the IP cameras via LAN/WAN. This NVR has two network ports, you can

select the network work pattern as required. Network fault tolerance

and multiple address setting are optional.

After you ﬁnish adding IP cameras, you can see the live images through

the monitor of the NVR. The following will mainly introduce how to add

the IP cameras via LAN/WAN.

5. Network Configuration

• LAN

1. Set the network of the NVR. Go to Start → Settings →

Network → TCP/IPv4. Input IP address, subnet mask, gateway,

etc. If using DHCP, please enable DHCP in both the NVR and

the router.

2. Go to Start → Settings → Network → Port. Input HTTP port

(the default value is 80), server port (the default port is 6036).

3. Click “Apply” to save the settings.

4. Go to Start → Settings → Camera → Add Camera. The NVR

will automatically refresh the cameras searched. The IPC which

supports the Onvif protocol may be added manually. If the IPC

searched is not in the same local network as the NVR, you

should select the device and click to modify the IP address.

4.0.0 .1.beta1

Versio n

192.1 68.1.20

192.1 68.1.38

XXX80

XXX

3.4.2

255.255.255.0

No.

IP Address

EditPort

Proto col Model

Subne t Mask

192.1 68.2.45

XXXXXX

255.255.255.0

Quickly Add

Manually Add

Add Camera

Selec ted: 1/3

Add

Defau lt Password

Remain Bandwidth: 108 / 120 Mb

Cancel

Mac Address

IP Address

Port

CE :98 :2 3 :75 :35 :22

Edit IP Camera

192 .168 . 1 . 45

255 . 255 . 255 . 0

admin

192 .168 . 1 . 1

Subnet Mask

Username

Gateway

Password

OK Cancel

4.0.0 .1.beta1

Versio n

192.1 68.1.20

192.1 68.1.38

XXX80

XXX

3.4.2

255.255.255.0

No.

IP Address

EditPort

Proto col Model

Subne t Mask

192.1 68.2.45

XXXXXX

255.255.255.0

Quickly Add

Manually Add

Add Camera

Selec ted: 1/3

Add

Defau lt Password

Remain Bandwidth: 108 / 120 Mb

Cancel

Mac Address

IP Address

Port

CE :98 :2 3 :75 :35 :22

Edit IP Camera

192 .168 . 1 . 45

255 . 255 . 255 . 0

admin

192 .168 . 1 . 1

Subnet Mask

Username

Gateway

Password

OK Cancel

4.0.0 .1.beta1

Versio n

192.1 68.1.20

192.1 68.1.38

XXX80

XXX

3.4.2

255.255.255.0

No.

IP Address

EditPort

Proto col Model

Subne t Mask

192.1 68.2.45

XXXXXX

255.255.255.0

Quickly Add

Manually Add

Add Camera

Selec ted: 1/3

Add

Defau lt Password

Remain Bandwidth: 108 / 120 Mb

Cancel

Mac Address

IP Address

Port

CE :98 :2 3 :75 :35 :22

Edit IP Camera

192 .168 . 1 . 45

255 . 255 . 255 . 0

admin

192 .168 . 1 . 1

Subnet Mask

Username

Gateway

Password

OK Cancel

4.0.0 .1.beta1

Versio n

192.1 68.1.20

192.1 68.1.38

XXX80

XXX

3.4.2

255.255.255.0

No.

IP Address

EditPort

Proto col Model

Subne t Mask

192.1 68.2.45

XXXXXX

255.255.255.0

Quickly Add

Manually Add

Add Camera

Selec ted: 1/3

Add

Defau lt Password

Remain Bandwidth: 108 / 120 Mb

Cancel

Mac Address

IP Address

Port

CE :98 :2 3 :75 :35 :22

Edit IP Camera

192 .168 . 1 . 45

255 . 255 . 255 . 0

admin

192 .168 . 1 . 1

Subnet Mask

Username

Gateway

Password

OK Cancel

1.Remove the cover and loosen the screws to take out two mounting bars.

2.Screw the shorter pillar attached with the NVR into the bottom of the device.

3. Install back the lower mounting bar and tighten the screws of the lower HDD.

TCP/IPv4

MAC Address

Ethe rn et P or t 1

Netw or k Fa ul t Tole ra nce

00：18：AE：35：6 4：1A

00：18：AE：35：6 4：1B

Port

DDNS

E-mail

NAT

UPnP Telnet

Obat in D NS a utomatica ll y

Pref er re d DNS

192 . 16 8 . 1 . 1

0 . 0 . 0 . 0

Alte rn at e DN S

IP Addr ess Settings

Obta in a n IP add re ss a utomatica ll y

Ethe rn et Por t 1 ( Onl ine )

Ethe rn et Por t 2 ( Onl ine )

IP Address

192 . 16 8 . 1 . 2

0 . 0 . 0 . 0

192 . 16 8 . 1 . 1

Subn et M as k

Gate wa y

Prim ar y Ca rd

Work Pattern

A UD I O

I N

A UD I O

O U T

H D MI

U S B

6 8 10

NO 1

G ND

C O

C OM

C O

A BY Z

K /BP /Z

A L A R M O U T

A L A R M I N

R S 4 85

Inte r ne t

L A N

V G A

1 0

1 2

1 3

1 4

1 5

1 6

P o E P o r ts

e - S A T A

Summary of content (2 pages)

PAGE 1
3. Rear Panel Installation After you finish adding IP cameras, you can see the live images through the monitor of the NVR. The following will mainly introduce how to add the IP cameras via LAN/WAN.
PAGE 2
5. Checkmark the device you want to add and then click “Add” button. The NVR will automatically refresh the cameras and return to “Edit Camera” interface. “Online” status means connecting the device successfully and you will see the live image. You may select the added device and click button to modify channel, IP address, ect. TCP/IPv4 Edit Camera Group Camera Name Port Status Protocol Model 1 IP Camera 1 192.168.1.20 80 Online XXX XXX 2 IP Camera 2 192.168.1.