Full Product Manual

ManualsBrandsAwnings in a Box ManualsAwnings8 ft. Traditional Manually Retractable Awning (26.5 in. Projection) in Pacific Blue

Basic Tools Required (not included)

•

Tape Measure & Pencil Level

• Phillips Screwdriver

•

Ladder

•

Drill with

⅛

” bit (Cement or Masonry bit for concrete installation)

•

Additional Hardware may be needed for non-standard installation

Note: Make sure that the door canopy you purchased exceeds the door width.

Allow for clearance for doors that open outward.

General Comments

•

Wash your hands before installation when handling the fabric.

•

Always be careful with the fabric during installation.

Drills, screwdrivers and other items can puncture the fabric.

Punctures during installation are not covered by the warranty.

•

A second person to assist in holding the awning during installation is

RECOMMENDED.

Included in awning kit

Item

Part Number

Description

Awnings Traditional & Classic

Designs

4 ft.

6 ft.

8 ft.

1200145

Head Rod Clamps

1200144

Hinge w/bolt attached

1200148

Eye End

1200093

Screws #10 (1 ½”)

1200146

Elbow

1200146

Pulleys

1200720

Internal Connectors

Installation Instructions

Traditional Awnings in a Box™

Classic Awnings in a Box™

Summary of content (6 pages)

PAGE 1
Installation Instructions Traditional Awnings in a Box™ Classic Awnings in a Box™ Basic Tools Required (not included) • • • • • Tape Measure & Pencil Level Phillips Screwdriver Ladder Drill with ⅛” bit (Cement or Masonry bit for concrete installation) Additional Hardware may be needed for non-standard installation Note: Make sure that the door canopy you purchased exceeds the door width. Allow for clearance for doors that open outward.
PAGE 2
H 1200142 Cleat 1 1 1 I 1410010 Instructions Sheet 1 1 1 J 1020010 21’ Pull Cord 1 1 1 K N/A Awning Fabric Cover 1 1 L 1300224 Arms (Outside Threaded Pipe) 2 2 2 M 1300222 (Inside Threaded Pipe with Black Cap on end) 2 2 2 N 1300225 2 2 2 O 1300223 0 2 4 1 Head Rod Bar Front Bar (Inside / Outside Threaded Pipe) Center Bar (Inside / Outside Threaded Pipe) ASSEMBLY DRAWING .
PAGE 3
Traditional & Classic Awning Assembly and Mounting 1. Measure and mark wall for head rod clamps 6 inches in from both sides of the window. a) Drill pilot or anchor holes for each head rod clamp. b) Fasten both head rod clamps to the wall, use a level to ensure clamps will be level with each other and centered above window. WINDOW 2. Assemble the Head Rod bar using the internal connector. There should be one 2 ft.
PAGE 4
7. Straighten the front bar; making sure the awning is level and straight. 8. Screw both camelback hinges into the wall. 9. Remove middle screw on the hinge and attach the Arms (eye end attached to the hinge). Tighten screw in slot. 10. Optional Pulley: Install tie down cleat on the side with the two pulleys.
PAGE 5
Product Care and Maintenance We use only quality fabrics in the manufacturing of our products, but fabrics do have a few limitations; proper care of your awning is important to extend its life. • • • • • • Clean awning fabric with a mild soap solution as needed (every 3 months), rinse thoroughly with water and allow to air dry (never put fabrics in your dryer). Keep the underside of your awning clean by brushing with a household broom.
PAGE 6
THE WARRANTY Warranties apply for 1 year from date of original purchase with proof of purchase (original receipt) Customer satisfaction and end user satisfaction is a number one concern and priority.