MANO110 Series AMD64 Athlon X2/Turion X2/Athlon Mini ITX Board with AMDRS780E+SB710 User’s Manual
Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual.
ESD Precautions Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets from electrostatic discharge damage, please take care of the following jobs with precautions: Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before holding the board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. It discharges static electricity from your body.
Table of Contents Disclaimers ............................................................................................ ii ESD Precautions .................................................................................. iii CHAPTER 1 ............................................................................................ 1 INTRODUCTION ..................................................................................... 1 1.1 Specifications ..........................................................
3.4 I/O Port Address Map ............................................................... 32 3.5 Interrupt Controller .......................................................... 33 CHAPTER 4 .......................................................................................... 34 AMI BIOS SETUP UTILITY................................................................... 34 4.1 Starting ............................................................................. 34 4.2 Navigation Keys ......................
MANO110 Series Mini ITX Board User’s Manual CHAPTER 1 INTRODUCTION The MANO110 is Mini ITX board with AMD Socket AM2/AM2+, TM TM TM support AMD Athlon X2/Turion X2/Athlon Processors. It TM integrates AMD RS780E with ATI Radeon HD3200 Graphics and SB710 that deliver outstanding system performance through highbandwidth interfaces, multiple I/O functions for interactive applications and various embedded computing solutions.
MANO110 Series Mini ITX Board User’s Manual 1.
MANO110 Series Mini ITX Board User’s Manual Ethernet Two RTL8111D Giga-bit Ethernet controllers via PCIe x1 Audio HD Audio compliant (with MIC-in/Line-in/line-out & Speaker) via ALC888 Amplifier: TPA3005D2 Stereo 6 Watt Power Management ACPI (Advanced Configuration and Power Interface) Form Factor Mini ITX form factor NOTE All specifications and images are subject to change without notice.
MANO110 Series Mini ITX Board User’s Manual 1.2 Utilities Supported Chipset Driver LAN Driver High Definition Audio Codecs Driver HDMI Audio Codecs Driver Note: Under Microsoft Windows XP operating systems the AMD Chipset Driver requires Microsoft .NET Framework prior to installation. The AMD Chipset Driver is an application that allows you to control the configuration of your AMD product. You can verify that you have the .
MANO110 Series Mini ITX Board User’s Manual CHAPTER 2 JUMPERS AND CONNECTORS 2.
MANO110 Series Mini ITX Board User’s Manual Solder Side Jumpers and Connectors 6
MANO110 Series Mini ITX Board User’s Manual Rear I/O 7 Jumpers and Connectors
MANO110 Series Mini ITX Board User’s Manual 2.
MANO110 Series Mini ITX Board User’s Manual Solder Side 9 Jumpers and Connectors
MANO110 Series Mini ITX Board User’s Manual 2.3 Jumper Settings Proper jumper settings configure the MANO110 to meet your application purpose. We are herewith listing a summary table of all jumpers and default settings for onboard devices, respectively.
MANO110 Series Mini ITX Board User’s Manual 2.3.
MANO110 Series Mini ITX Board User’s Manual Description COM3 (JP2) Function Jumper Setting Pin 1=5V *Pin 1=DCD (Default) Pin 8=12V *Pin 8=RI (Default) Jumpers and Connectors 12
MANO110 Series Mini ITX Board User’s Manual 2.3.2 CF Mode Setting Jumpers (JP5) Description CF Mode Select Function Jumper Setting Slave(Default) Master 2.3.3 CF Power Setting Jumpers (JP5) Description CF Power Select Function Jumper Setting +5V(Default) +3.
MANO110 Series Mini ITX Board User’s Manual 2.3.4 CMOS Clear Jumpers (JP6) You may need to use this jumper is to clear the CMOS memory if incorrect settings in the Setup Utility.
MANO110 Series Mini ITX Board User’s Manual 2.4 Connectors Description PS/2 Keyboard and Mouse Connector DVI and VGA Connector HDMI Connector COM1 Connector LAN1, USB Port1 and USB Port2 Connector LAN2, USB Port2 and USB Port4 Connector Audio Connector Reserved.
MANO110 Series Mini ITX Board User’s Manual 2.4.1 PS/2 Keyboard and Mouse Connector (CN1) The board supports one PS/2 keyboard and Mouse interface. Pin Signal Pin Signal 1 K/B Data 7 M/S Data 2 NC 8 NC 3 GND 9 GND 4 VCC 10 VCC 5 K/B CLK 11 M/S CLK 6 NC 12 NC 2.4.2 VGA+DVI Connector (CN2) CN2 is a double deck VGA & DVI connector. CN2A is a standard 15-pin DB15 connector commonly used for the CRT VGA display.
MANO110 Series Mini ITX Board User’s Manual Pin 1 3 Signal Pin Signal TX2- 2 TX2+ Ground 4 CRT_SPD_CLK 5 CRT_SPD DATA 6 DVI_SPD_CLK 7 DVI_SPD DATA 8 CRT-VSYNC 9 TX1- 10 TX1+ 11 Ground 12 NC 13 NC 14 VGAVCC 15 Ground 16 FPDETECT 17 TX0- 18 TX0+ 19 Ground 20 NC 21 NC 22 Ground 23 TXC+ 24 TXC- C1 CRT-RED C2 CRT-GREEN C3 CRT-BLUE C4 CRT-HSYNC C5 VGAGND CN2B(DVI-D+CRT2) 17 Jumpers and Connectors
MANO110 Series Mini ITX Board User’s Manual 2.4.3 Pin HDMI Connector (CN3) Signal Pin Signal 1 TMDS Data2+ 2 3 TMDS Data2– 4 TMDS Data1+ 5 TMDS Data1 Shield 6 TMDS Data1– 7 TMDS Data0+ 8 TMDS Data0 Shield 9 TMDS Data0– 10 TMDS Clock+ 11 TMDS Clock Shield 12 TMDS Clock– 13 CEC 14 Reserved (N.C. on device) 15 SCL 16 SDA DDC/CEC Ground 18 +5 V Power 17 19 Hot Plug Detect TMDS Data2 Shield 20 HDMI Connector (CN3) 2.4.
MANO110 Series Mini ITX Board User’s Manual 2.4.5 USBx2 + LAN Connectors (CN5, CN6) The board supports two three-layer USB & LAN connectors, CN5 and CN6. The upper CN5B and CN6B ports are for LAN. The board is equipped with a high performance Plug and Play Ethernet interface fully compliant with the IEEE 802.3 standard.
MANO110 Series Mini ITX Board User’s Manual 2.4.6 Audio Phone Jack Connector (CN7) 2.4.7 Speaker Output Connector (CN10) 1 negative output for left channel 2 positive output for left channel 3 negative output for right channel 4 positive output for right channel 2.4.8 ATX 12V Power Connector (CN13) Connect the power cable to ATX1 for +12V ATX power supply.
MANO110 Series Mini ITX Board User’s Manual 2.4.9 CPU Fan Connector (CN14) FAN1 is a CPU fan connector. The fan connector on MANO110 provides power to the fan. 2.4.10 SATA Connectors (CN15, CN16) These SATA connectors are for high-speed SATA interface ports and they can be connected to hard disk devices. Pin Signal 1 2 GND SATA_TX+ 3 4 SATA_TXGND 5 SATA_RX- 6 7 SATA_RX+ GND 2.4.
MANO110 Series Mini ITX Board User’s Manual 2.4.12 USB Port5 ~ Port8 Connectors (CN19, CN20) These Universal Serial Bus (USB) connectors on this board are for installing versatile USB interface peripherals. These are 10-pin standard USB connectors.
MANO110 Series Mini ITX Board User’s Manual 2.4.13 COM2, COM3 and COM4 Connectors (CN30,CN24,CN25,) Please refer to the RS-232 pin assignment as listed below: Pin Signal Pin Signal 1 Data Carrier Detect (DCD) 2 Data Set Ready (DSR) 3 Receive Data (RXD) 4 Request to Send (RTS) 5 Transmit Data (TXD) 6 Clear to Send (CTS) 7 Data Terminal Ready (DTR) 8 Ring Indicator (RI) 9 Ground (GND) 10 Key 2.4.
MANO110 Series Mini ITX Board User’s Manual 2.4.15 Mini PCIe slot (CN27) CN27 is a PCI Express Mini Card connector with support for a PCI Express x1 link and a USB 2.0 link. A PCI Express Mini Card can be applied to either PCI Express or USB 2.0. The USB 2.0 support will be helpful during the transition to PCI Express, because peripheral vendors will need time to design their chipsets to have the PCI Express function.
MANO110 Series Mini ITX Board User’s Manual Pin 25 Signal Pin Signal 45 N.C 46 N.C 47 N.C 48 +1.5V 49 N.C 50 GND 51 N.C 52 CN27 +3.
MANO110 Series Mini ITX Board User’s Manual 2.4.16 ATX Power Connector (CN28) Steady and sufficient power can be supplied to all components on the board through the power connector. Please make sure all components and devices are properly installed before connecting the power connector. If you use a 20-pin ATX power supply, please remove the small cover from the power connector before plugging in the power cord; otherwise, please do not remove it. Pin Signal Pin Signal 1 3.3V 2 3.
MANO110 Series Mini ITX Board User’s Manual 2.4.17 DIO Connector (CN29) The board is equipped an 8-channel digital I/O connector CN29 that meets requirements for a system customary automation control. The digital I/O can be configured to control cash drawers, sense warning signals from an Uninterrupted Power System (UPS), or perform store security control. The digital I/O is controlled via software programming.
MANO110 Series Mini ITX Board User’s Manual 2.4.18 Flat Panel Bezel Connector (CN31) Power LED This 3-pin connector named as Pin 1, 3 and Pin 5 connect the system power LED indicator to such a switch on the case. Pin 1 is assigned as +, and Pin 3, Pin 5 as -. The Power LED lights up when the system is powered ON. External Speaker and Internal Buzzer Connector Pin 2, 4, 6 and 8 can be connected to the case-mounted speaker unit or internal buzzer.
MANO110 Series Mini ITX Board User’s Manual 2.4.19 CF Connector (CN32) TM The board is equipped with a CompactFlash disk type-II socket on the solder side to support an IDE interface TM CompactFlash disk card with DMA mode supported. The socket is especially designed to avoid incorrect installation of TM the CompactFlash disk card. When installing or removing TM the CompactFlash disk card, please make sure the system TM power is off.
MANO110 Series Mini ITX Board User’s Manual 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Hardwarre Description 30
MANO110 Series Mini ITX Board User’s Manual CHAPTER 3 HARDWARE DESCRIPTION 3.1 Microprocessors TM TM The MANO110 Series supports AMD Athlon X2/Turion TM , X2/Athlon Processors which make your system operated under W indows7 and Linux environments. The system performance depends on the microprocessor. Make sure all correct settings are arranged for your installed microprocessor to prevent the CPU from damages. 3.
MANO110 Series Mini ITX Board User’s Manual 3.4 I/O Port Address Map There are total 1KB port addresses available for assignment to other devices via I/O expansion cards .
MANO110 Series Mini ITX Board User’s Manual Address 3.5 Devices 3D0-3DF CGA card 3F8-3FF Serial port #1 (COM1) 3E8-3EF Serial port #3 (COM3) 2F8-2FF Serial port #2 (COM2) 2E8-2EF Serial port #4 (COM4) Interrupt Controller The MANO110 Series is a 100% PC compatible control board. It consists of 16 interrupt request lin es, and four out of them can be programmable. The mapping list of the 16 interrupt request lines is shown as the following table.
MANO110 Series Mini ITX Board User’s Manual CHAPTER 4 AMI BIOS SETUP UTILITY This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility. 4.1 Starting To enter the setup screens, follow the steps below: 1. 2. 4.2 Turn on the computer and press the key immediately. After you press the key, the main BIOS setup menu displays.
MANO110 Series Mini ITX Board User’s Manual 35 Esc The key allows you to discard any changes you have made and exit the Setup. Press the key to exit the setup without saving your changes. Enter The key allows you to display or change the setup option listed for a particular setup item. The key can also allow you to display the setup sub- screens.
MANO110 Series Mini ITX Board User’s Manual 4.3 Main Menu When you first enter the Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below. System Time/Date Use this option to change the system time and date. Highlight System Time or System Date using the keys. Enter new values through the keyboard.
MANO110 Series Mini ITX Board User’s Manual 4.4 Advanced Menu The Advanced menu allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: CPU Configuration Chipset Onboard Device Configuration USBConfiguration PCIPnP For items marked with “”, please press for more options.
MANO110 Series Mini ITX Board User’s Manual CPU Configuration This screen shows the CPU Configuration.
MANO110 Series Mini ITX Board User’s Manual Advanced Chipset Settings 39 AMI BIOS Setup Utility
MANO110 Series Mini ITX Board User’s Manual Primary Video Controller. IGFX-GFX0-GPP-PCI: Display from onboard VGA first. GFX0-GPPIGFX-PCI: Display from external PCIe VGA card first. UMA Frame Buffer Size. Frame buffer size is the total amount of system memory allocated solely for the onboard graphics controller. MS-DOS, for example, will use only this memory for display. Options are: Auto (default), 128MB, 256MB, 512MB. FB Location. The optional settings are: Below 4G; Above 4G.
MANO110 Series Mini ITX Board User’s Manual Onboard Device Configuration Onboard LAN Boot. Use these items to enable or disable the Boot ROM function of the onboard LAN chip when the system boots up. HD Audio Azalia Device. Use these items to enable or disable the audio function of the onboard audio chip when the system boots up. Serial Port1 Address This item specifies the base I/O port address and Interrupt Request address of serial port 1. The Optimal setting is 3F8/IRQ4.
MANO110 Series Mini ITX Board User’s Manual Serial Port3 IRQ This item specifies the IRQ used by the serial port 3. Serial Port4 Address This item specifies the base I/O port address . Request address of serial port 4. The Optimal setting is 2E8. Serial Port4 IRQ This item specifies the IRQ used by the serial port 4.
MANO110 Series Mini ITX Board User’s Manual USB Configuration You can select options for the USB Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. Legacyu USB Support Use this item to enable or disable support for USB device on legacy operating system. The default setting is Enabled. USB 2.0 Controller Mode Use this item to configure the USB 2.0 controller. The default setting is FullSpeed.
MANO110 Series Mini ITX Board User’s Manual PCI/PnP Settings AMI BIOS Setup Utility 44
MANO110 Series Mini ITX Board User’s Manual Clear NVRAM Use this item to clear the data in the NVRAM (CMOS). Here are the options for your selection, No and Yes. Plug & Play O/S When the setting is No, Use this item to configure all the devices in the system. When the setting is Yes and if you install a Plug and Play operating system, the operating system configures the Plug and Play devices not required for boot. The default setting is No.
MANO110 Series Mini ITX Board User’s Manual 4.5 Power ACPI Settings Suspend mode Use this item to select the ACPI state used for System Suspend. The optional settings are: S1 (POS); S3 (STR). Repost Video on S3 Resume This feature allows you to repost video on S3 resume. ACPI Version Features Set this value to allow or prevent the system to be complaint with the ACPI version.
MANO110 Series Mini ITX Board User’s Manual Power Management Power Button Mode This option specifies how the externally mounted power button on the front of the computer chassis is used. The default setting is On/Off Keyboard PowerOn Keyboard set to support power on function. Mouse PowerOn Mouse set to support power on function. Restore on AC Power Loss This item can control how the PC will behave once power is restored following a power outage, or other unexpected shutdown.
MANO110 Series Mini ITX Board User’s Manual Hardware Health Configuration Cuban Mode Setting (Smart Fan) When set to disable, the CPU FAN are always on. Temperature 1 Limit of Highest Set the temperature limit for CPU FAN high speed. Temperature 1 Limit of Lowest Set the temperature limit to for CPU FAN low speed.
MANO110 Series Mini ITX Board User’s Manual 4.6 Boot Menu The Boot menu allows users to change boot options of the system. You can select any of the items in the left frame of the screen to go to the sub menus: Boot Device Priority Hard Disk Drives Security Boot Settings Configuration For items marked with “”, please press for more options.
MANO110 Series Mini ITX Board User’s Manual Boot Device Priority The Boot Device Priority screen specifies the order in which the system checks for the device to boot from the available devices.
MANO110 Series Mini ITX Board User’s Manual Hard Disk Drives Use this screen to view the hard disk drives in the system.
MANO110 Series Mini ITX Board User’s Manual Security Settings Change Supervisor Password Select this option and press to access the sub menu. You can use the sub menu to change the supervisor password.
MANO110 Series Mini ITX Board User’s Manual Boot Settings Configuration Quick Boot Enabling this item lets the BIOS skip some power on self tests (POST).The default setting is Enabled. AddOn ROM Display Mode This item selects the display mode for option ROM. The default setting is Force BIOS. Boot Num-Lock Use this item to select the power-on state for the NumLock. The default setting is On.
MANO110 Series Mini ITX Board User’s Manual 4.7 Exit Menu The Exit menu allows users to load your system configuration with optimal or failsafe default values. Save Changes and Exit When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Exit from the Exit menu and press . Select Ok to save changes and exit.
MANO110 Series Mini ITX Board User’s Manual Discard Changes Use this item to abandon all changes. Load Optimal Defaults It automatically sets all Setup options to a complete set of default settings when you select this option. The Optimal settings are designed for maximum system performance, but may not work best for all computer applications. In particular, do not use the Optimal Setup options if your computer is experiencing system configuration problems.
MANO110 Series Mini ITX Board User’s Manual APPENDIX A WATCHDOG TIMER A1 Watchdog Timer After the system stops working for a while, it can be auto-reset by the Watchdog Timer. The integrated Watchdog Timer can be set up in the system reset mode by program. A1.1 Program Watchdog Timer The W atchdog timer is built in super I/O F71863. The F71863 I/O address port is 2E hex and 2F hex. 2E hex is index port. 2F hex is data port.
MANO110 Series Mini ITX Board User’s Manual Watchdog Timer Register Index Port (2E hex) Data Port (2F hex) Description 87 hex --- Unlock Super I/O. Two successive writes of 87 hex be applied to 2E hex. 2B hex (F71863) Bit 4 Select W DTO pin function. 1: W DT Output. 0: GPIO14. 07 hex 07 hex Select register of watchdog timer 30 hex Bit 0 W rite 1 to enable watchdog timer. Disable is write 0. F0 hex Bit 7 W rite 1 to enable W DTO# output F5 hex Bit 3 W rite 0 set second as counting unit.
MANO110 Series Mini ITX Board User’s Manual Watchdog Timer Register Index Port (2E hex) Data Port (2F hex) Description F6 hex Value 0: Stop timer. 1~FF hex: W rite non-zero value the counter to load the value to watchdog counter and start counting down. W rite new value to this register can reset timer to count with the new value. AA hex --- Lock Super I/O W rite AA hex to 2E/2F hex.
MANO110 Series Mini ITX Board User’s Manual A1.2 Example Program Code The sample code is for debug.exe. Sample code is index port 2E hex, data port 2F hex and time-out value 30 second. A1.2.
MANO110 Series Mini ITX Board User’s Manual A1.2.
MANO110 Series Mini ITX Board User’s Manual 1.2.
MANO110 Series Mini ITX Board User’s Manual APPENDIX B DIGITAL I/O Digital I/O Software Programming Example Pin Signal Pin Signal 1 DIO0 2 DIO4 3 DIO1 4 DIO5 5 DIO2 6 DIO6 7 DIO3 8 DIO72 9 GND 10 +5V CN29 GPIO control #define SMBusBase 0x0B00 #define PCA9554SlaveAddr 0x40 #define ICH_SMBUS_HOST_STAT 0x00 #define ICH_SMBUS_HOST_CTRL 0x02 #define ICH_SMBUS_HOST_CMD 0x03 #define ICH_SMBUS_HOST_ADDR 0x04 #define ICH_SMBUS_HOST_DATA_0 0x05 #define ICH_SMBUS_HOST_DATA
MANO110 Series Mini ITX Board User’s Manual Configure GPIO pin direction as 4 inputs and 4 outputs outb(0xFF,SMBusBase + ICH_SMBUS_HOST_STAT); // Clear host status outb(PCA9554SlaveAddr, SMBusBase + ICH_SMBUS_HOST_ADDR); // Set slave address outb(0x03, SMBusBase + ICH_SMBUS_HOST_CMD); // Configuration register for PCA9554 outb(0xF0, SMBusBase + ICH_SMBUS_HOST_DATA_0); // outb(0x48, SMBusBase + ICH_SMBUS_HOST_CTRL); // Trigger SMBus Byte operation Configure GPIO output pin to high outb(0xFF,SMBusBase + ICH
