Datasheet

EIRx-Sx series-0106 - 2/2
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
815-433-5100 Fax [phone] www.bb-elec.com [e-mail] [e-mail]
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
[phone] Fax [phone]
www.bb-europe.com [e-mail] [e-mail]
PRODUCT INFORMATION B&B ELECTRONICS
Link-fault-pass-through
Link-Fault-Pass-Through Overview
When two Media Converters are connected via their
fiber ports
Link Fault of the FX port:
A Link Fault condition will be sensed on the RJ45 port
whenever the media converter detects a Link Fault
condition on the Fiber port. (The 10/100, LNK/ACT, and
FDX/COL LED’s will be off.)
Link Fault of the TX port:
The Media Converter A
: A Link Fault condition will be
sensed on the FX port whenever the media converter
detects a Link Fault condition on the TX port. Thus, the
100, LNK/ACT, and FDX/COL LEDs of the TX port of the
Media Converter A would be off.
The Media Converter B:
A Link Fault condition will be
informed to the FX port of the Media Converter B. Then
a Link Fault condition will be sensed on the TX port of
the Media Converter B whenever the Media Converter B
detects a Link Fault condition on the FX port. Thus, the
100, LNK/ACT, and FDX/COL LEDs of the Media
Converter B would be off.
Link Fault of the FX Port
TX Port FX Port
LEDs PWR 100 LNK/ACT FDX/COL LNK/ACT FDX/COL
Media Converter A ON OFF OFF OFF OFF OFF
Media Converter B ON OFF OFF OFF OFF OFF
Link Fault of the TX port of the Media Converter A
TX Port FX Port
LEDs PWR 100 LNK/ACT FDX/COL LNK/ACT FDX/COL
Media Converter A ON OFF OFF OFF ON ON
Media Converter B ON OFF OFF OFF OFF OFF
Functional Description
• Meets NEMA TS1/2 Environmental requirements
such as temperature, shock, and vibration for traffic
control equipment.
• Meets IEC61000-6-2 EMC Generic Standard
Immunity for industrial environment.
• One channel media converter between
10/100BaseTx and 100BaseFx
• Support 802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, Full/half-duplex; Auto MDI/MDIX.
• 100BaseFX: Multi mode SC or ST type; Single mode
SC type.
• DIP switch for configuring link-fault-pass-through,
fixed speed, full/half duplex and link down alarm
• Store-and-forward mechanism
• Non-blocking full wire-speed forwarding rate
• Support broadcast storm filtering
• Back-pressure & IEEE 802.x compliant flow control
• Alarms for power failure by relay output.
• Redundant 10-48 VDC terminal block power inputs.
• Operating temperature ranges from -34 to 74°C.
• Supports DIN-rail mounting installation.
• Front panel LED status
Assembly, Startup, and Dismantling
• Assembly: Place the media converter on the DIN rail
from above using the slot. Push the front of the media
converter toward the mounting surface until it audibly
snaps into place.
• Startup: Connect the supply voltage to start up the
media converter via the terminal block.
• Dismantling: Pull out the lower edge and then remove
the media switch from the DIN rail.
Specifications
Applicable Standards IEEE 802.3 10BaseT,
IEEE 802.3u 100BaseTX & 100BaseFX
Fixed Ports (1) TX port, (1) FX port
10/20Mbps for half/full-duplex Speed 10BaseT
100BaseTX/FX
100/200Mbps for half/full-duplex
Switching Method Store-and-Forward
Forwarding rate 14,880/148,800pps for 10/100Mbps
Cable
10BaseT
100BaseTX
100BaseFX
2-pair UTP/STP Cat. 3, 4, 5 up to 100m
2-pair UTP/STP Cat. 5 up to 100m
MMF (50 or 62.5µm), SMF (9 or 10µm)
Per Unit - PWR1, PWR2, FAULT, LFP LED Indicators
Per Port - TX: LNK/ACT, FDX/COL, 100
FX: LNK/ACT, FDX/COL
Dimensions 2 x 4.3 x 5.4 in. (5 x 11 x 13.6cm)
Weight 0.6 Kg
Power Terminal Block: 200mA @ 24VDC, 10-48VDC
Power Consumption 4.8W Max.
Operating Temperature -34°C to 74°C
Storage Temperature -45°C to 93°C
Humidity 10 to 95%, non-condensing
Emissions FCC Part 15, Class A
CE: EN55022 (CISR22 Class A)
EN55024 (CISPR24 Class A)
Standards
ESD Standard (IEC 61000-4-2)
Radiated FRI Standards (IEC 61000-4-3)
Burst Standards (IEC 61000-4-4)
Surge Standards (IEC 61000-4-5)
Induced RFI Standards (IEC 61000-4-6)
Magnetic Field Standards (IEC 61000-4-8)
Voltage Dips Standards (IEC 61000-4-11)
Environmental Test Compliance:
Vibration Resistance (IEC 60068-2-6)
Shock (IEC 60068-2-27)
Free Fall (IEC 60068-2-32)
NEMA TS1/2 Environmental requirements for traffic control equipment