Spa Owner's Manual FOR SPOR UB America's Get Away Spa! NOTE: Important Safety Instructions. Please read and follow all instructions before installing, operating or enjoying your spa. Please refer to the operational video that is supplied with spa. Save these instructions for future reference. UL ® UNDERWRITER'S LABORATORIES REV01/06 HOTTUBS.
A Brief History of Spas During the 5th century B.C., the mineral springs in Greece and the Aegean Islands served as healing clinics. At one particular clinic on the Island of Cos, a Greek physician Hypocrites practiced medicine while writing extensively on hydrotherapy. In the province of Leige, Belgium mineral springs were favored for centuries by notables and royalty, including Russian Czar Peter the Great and German Kaiser William II.
SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. WARNING - To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. 3. A wire connector is provided on this unit to connect a minimum No. 8 AWG (8.
SAFETY INSTRUCTIONS 11. Do not use the spa alone. 12. People with infections, skin sores or open wounds should not use the spa. 13. It is recommended that people shower before and after using the spa in order to keep spa operating cleaner, and to rinse off spa water chemicals. 14. Disconnect all electrical power before attempting any kind of service to the electrical module. 15. Always use unbreakable containers around the spa. Never use glass. 16.
SAFETY INSTRUCTIONS 20. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6 °F. The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness and fainting.
INSTALLATION GUIDELINES 5 1. Locate your spa on a solid, level surface that is structurally strong enough to Support its filled weight. 2. Installations on wooden decks or balconies should be checked to insure that the floor can support the weight of the full spa and the persons using it. 3. A reinforced poured concrete slab (min. 4" thick) is recommended. However, wood decking is also acceptable, provided it is constructed so that it meets the requirements outlined above. (see No. 2) 4.
120 VOLT INSTALLATION The provided power supply cord must be connected to a receptacle with a minimum circuit breaker size of 15 amperes. No other electrical appliance or fixture should be used on this circuit. The heater will provide 1100 watts (1.1 kw) of heat when the pump is operating in low speed and thermostat is calling for heat. Under no circumstances should an extension cord be used.
7
INITIAL STARTUP WARNING IN ORDER TO CHECK FOR POSSIBLE LEAKS, THE FOLLOWING STEPS ARE PERFORMED WITHOUT THE WOOD SKIRTING IN PLACE. TO PREVENT RISK OF ELECTRICAL SHOCK, DO NOT USE SPA AT THIS TIME. 1. 120 Volt Units: Make sure the power supply cord is "unplugged" 240 Volt Units: Make sure the power supply is "OFF". 2. Check to see that the Drain Valve (located to the left side of Equipment Module) is closed. 3. The slide valves on each side of the Equipment Module should be open.
SPORTUB 1050-54-56 Controller Operations JETS KEY: The Jets key is used to turn the pump on or off at selected speeds. The first press will turn on the pump HIGH speed, the second press will change the pump to LOW speed, the third press will turn the pump off or return to a heat or filtration mode (see note). A built-in timer will shut the pump off 20 minutes after it has been started unless the user does so manually. When the pump is on, the Jets On Indicator will appear above the Jets key.
SPORTUB II 1057-58 Controller Operations Programming Cycle Duration You may choose to filter spa 60, 120, 180 or 480 minutes per cycle as needed to maintain filtered water. To view the current length of each filter cycle, press & hold the Light button for 5 seconds. The current length of each filtration cycle will then be shown. This setting can be modified by holding the Up/Down button until the length of each cycle is shown.
QUICK PROGRAMMING NOTES IF YOU APPLY POWER TO SYSTEM AND DO NOTHING ELSE: 1. The primary filter cycle will occur in 24 hours and run for 120 min. This will repeat every 24 hours. 2. The spa will heat up to and maintain 100º F. (The freeze protection mode is available if required.) TO SET OR CHANGE THE FILTER CYCLE START TIMES: Refer to PROGRAMMING FILTER CYCLES in operating manual.
INSTALLING YOUR PURIFICATION DISPENSER There are several ways that the water chemistry can been maintained in your Baja Spas. As the photo's indicate below, Baja’s built in KLEEN H20 dispenser incorporates the filter lid for either chlorine / bromine tablets or Nature 2 purification system. The Nature 2 purification system, is only recommended for personal use or family spa installation. Chlorine/Bromine or similar is recommended for regular and heavy bather installation.
CABINET INSTALLATION 1 4 Attach coupling blocks to one end of side panel with toggle bolts and tool supplied with cabinet. (PS 1042, WW 1067/ 68) 2 Align with another side panel. Insert bolts and tighten securely. Install corner posts (pay attention to "up" arrows) to side panels, then small panels to each corner post around spa using panel bolts and bolt driver. 5 3 Position side panels under spa lip with black kickboard on the bottom. Completed Baja spa.
SPA MAINTENANCE SCHEDULE DAILY - CHECK WATER LEVEL, REFILL IF NECESSARY TO LINE ON SKIMMER PLATE. - CHECK CHEMICAL READING AND ADJUST AS NEEDED. - FOR PROPER FILTRATION, THE WATER SHOULD BE CIRCULATING FOR AT LEAST FOUR HOURS A DAY. WEEKLY - WIPE DOWN THE WATER LINE. - CHECK WATER FLOW AND CLEAN FILTER IF NECESSARY. MONTHLY - CLEAN FILTER CARTRIDGE. - CLEAN THE INSULATED SPA COVER. - TEST THE GFCI. THREE MONTHS - DRAIN THE SPA COMPLETELY, REFILL WITH WATER AND REPLENISH CHEMICALS.
REGULAR SPA MAINTENANCE EON SYNTHETIC CABINET: Your modular cabinet has been treated with a stain at the factory. It is suggested that the cabinet be treated annually with an additional coat of stain for maximum weather protection. Contact your Baja Spa Retailer for advice on which stain and oil work best in your area. DRAINING THE SPA (SEE PAGE 13): It is recommended to completely drain the spa at least four times a year. More frequent draining may be required depending on usage.
TROUBLESHOOTING Air lock plumbing system. “Bleed” the system, see start-up procedure page 8.
3 DOT CONTROL PANEL ALARMS SMART WINTER MODE/FREEZE PROTECTION: On board temperature sensors continuously monitor water and air temperature. If the temperature inside the control box falls below 59°F, the system will start a special program (Smart Winter Mode) to circulate the water in the plumbing. For the next 24 hours, the components will be automatically operated for a period of 1 minute every 2 hours to thoroughly circulate the water throughout the spa.
3 DOT ERROR IDENTIFICATION System Error LED 3 flashing dots below the temperature display is an indication that an error has occurred. To identify the error, follow these procedures: 1) Open the front cover of the systems control box. 2) Verify if the system error LED is illuminated on the printed circuit board. System Error LED not Illuminated: With Pump Running a) Press the Temp. Down Key to lower the temperature below the current water temperature.
Spa Delivery Checklist Dealer Name______________________________________________________________ Purchaser Information Name ___________________________________________________________ Address _________________________________________________________ _________________________________________________________ Phone (______)__________________________________ Spa Information Model______________________ Serial#________________________ Color_______________________ Equipment serial#______________________ Date
