Owner`s manual

TEMPERATURE PROGRAM KEYS: The
Up/Down Temperature Program keys are
used to set the desired water temperature.
Press the Up or Down keys to Increase (or
decrease) the desired temperature setting. The temperature
can be adjusted in 1ºF increments from 59ºF to 104ºF (or 15ºC
to 40º C). The desired temperature setting will remain in the
display for 5 seconds as confirmation of the new value, after 5
seconds the display will return to display the present water
temperature. NOTE: The Temperature Program Indicator will
appear to indicate that the temperature in the display is the
desired-programmed temperature and not the actual water
temperature.
HEATER OPERATION: When the water temperature drops
1ºF lower than the desired temperature, the heater will be
turned on until the water temperature reaches the desired
temperature plus 1ºF. The Heater On Indicator will appear on
the function panel when it is on. The Heater On Light Indicator
will blink on the function panel whenever there is a call for heat
and the heater has not yet been activated.
FREEZE PROTECTION: When the system senses cold
temperatures, it will automatically engage the freeze protection
mode for a monitoring period of 24 hours. During this time, the
pump will operate for 1 minute every 2 hours to circulate warm
water through the plumbing. When the pump is running due to
this feature, the Filter Cycle Indicator on the spaside panel will
blink. Filter Cycles will operate as determined by the program-
ming and will not be affected by the Freeze Protection Mode.
HIGH TEMPERATURE PROTECTION: If the water temper-
ature exceeds 122ºF at the High Temperature probe, the
system will display the message HL and will turn the heater off.
After the water temperature has cooled down, pressing any
key on the spaside panel control will allow the system to
restart. If the spa water temperature does not seem to be
elevated, the HL reading may have been caused by poor water
flow or electrical line interference (e.g. thunderstorms, voltage
surges, etc.). Simply reset and monitor the system. See
Troubleshooting, page 17. NOTE: The Freeze Protection
Circuit is in effect at all times that there is power applied to the
system and will automatically engage if needed.
DEFAULT SYSTEM OPERATIONS: When power is applied, or
there is a temporary loss of power, the system will initiate it's
default programming. The filter cycle starts 24 hours after the
system has been powered up, filters for one hour, and then
repeats every 24 hours. The maintained temperature will
default to 100º F. The freeze protection feature will stay in
effect. If a power loss condition is experienced, the spaside
display will blink until any key is pressed. This feature is to let
the user know that a power failure has occurred and that the
Temperature Program point has returned to the default value.
JETS KEY: The Jets key is used to turn the
pump on or off at selected speeds. The first
press will turn on the pump HIGH speed, the
second press will change the pump to LOW
speed, the third press will turn the pump off or return to a
heat or filtration mode (see note). A built-in timer will shut
the pump off 20 minutes after it has been started unless
the user does so manually. When the pump is on, the
Jets On Indicator will appear above the Jets key. NOTE:
You may not be able to turn the pump off if it has started
a filtration cycle or if the spa is calling for additional
heating. This is easily identified by observing the status
of the "Heater On Indicator" or the "Filter Cycle
Indicator".
LIGHT KEY: The Light key is used to turn the
light on or off. The first press of the Light key
will turn the light on. A second press will turn
the light off. The light will automatically turn
itself off after 2 hours. When the light is on, the Light On
Indicator will appear above the Light key.
PROGRAMMING FILTER CYCLES: You may choose to
filter your spa 1, 2, or 3 times daily as required to
maintain clean, sanitary water. At the same time, press
and release both the Jets key and the Up Arrow key.
The current setting for filtration cycle frequency will be
displayed. Do nothing and the control will revert to the
Default System Operation Mode, OR, to change the
frequency, press the Up or Down Arrow key. Pressing
the Jets key and Up Arrow key at the same time again
will start a Filtration Cycle, otherwise, the first cycle will
start 24 hours from the programming time. NOTE: The
cycles will repeat every 24, 12, or 8 hours within a 24
hour period, starting from the time programmed. It is
recommended that the system be powered up at a time
when the programmed cycles do not interfere with
sleeping hours.
PROGRAMMING CYCLE DURATION: You may choose
to filter your spa 60, 120, or 180 minutes per cycle as
required to maintain clean, sanitary water. At the same
time, press and release both the Light key and the Up
Arrow key. The current setting for filtration cycle duration
will be displayed (60,120,180). Do nothing and the
control will revert to the Default System Operation Mode,
OR, to change the frequency, press the Up or Down
Arrow key.
IMPORTANT PROGRAMMING NOTES: (1) If a program
change is not made within 5 seconds, the system will
default back to the monitoring mode. (2) While
programming, the Pump and Light features may have
been activated. Either can be turned off in the normal
way after programming is complete. The display will
return to indicate water temperature 5 seconds after the
keys are released.
9
SPORTUB 1050-54-56 Controller Operations
ADDITIONAL PROGRAMMING:To set temperature unit
( F or C) press and hold the light key for 5 seconds. This will
switch the system to the temperature that you prefer. Once the
selection has been made simply wait until the spaside control
reverts back to the temperature made.