Installation Template

Template for PD006 Trim
Plantilla para el contramarco PD006
Gabarit pour la plaque de  nition PD006
Fold
Doble
Plier
Fold
Doble
Plier
Fold
Doble
Plier
Fold
Doble
Plier
4.6"
116,8 mm
4.6"
116,8 mm
2"
50,8 mm
2.36"
59,9 mm
0.15" (3,8 mm)
deep
QSPGVOEJEBE
QSPGPOEFVS
2"
50,8 mm
C
L
lock tDFSSBEVSBtTFSSVSF
8632
8602
8603
8601*
Ø 5/64"
3/4" (19,1 mm)
deep
QSPGVOEJEBE
QSPGPOEFVS
4X Ø 5/64"
3/4" (19,1 mm)
deep
QSPGVOEJEBE
QSPGPOEFVS
4X
3.75"
95,3 mm
5.56"
141,2 mm
5.56"
141,2 mm
3.75"
95,3 mm
2.36"
59,9 mm
0.15" (3,8 mm)
deep
QSPGVOEJEBE
QSPGPOEFVS
*If using a 8601 passage mortise, the trim plates may be
positioned anywhere on the door, as the trim does not interact
with the mortise box.
4JVUJMJ[BVOBNPSUBKBEFQBTPMBTQMBDBTEFMDPOUSBNBSDPQVFEFO
VCJDBSTFFODVBMRVJFSQBSUFEFMBQVFSUBZBRVFFMDPOUSBNBSDPOPJOUFSBDUÞB
DPOMBDBKBEFNPSUBKB
&ODBTEVUJMJTBUJPOEFMBNPSUBJTFEFQBTTBHFMFTQMBRVFTEFGJOJUJPO
QFVWFOUÐUSFTJUVÏFTËOJNQPSUFRVFMFOESPJUTVSMBQPSUFQVJTRVFDFMMFTDJ
OPOUQBTEJOGMVFODFTVSMBNPSUBJTF
Top line of 8632/8602/8603 mortise face
-ÓOFBTVQFSJPSEFMBDBSBEFNPSUBKB
-JHOFTVQÏSJFVSFEVEFWBOUEFTNPSUBJTFT
8601 Passage Mortise Box*
$BKBEFNPSUBKBEFQBTP
.PSUBJTFEFQBTTBHF
If backset is 2-1/2" (63,5 mm)
4JMBEJTUBODJBBMDFOUSPFT" (63,5 mm)
Si le ÏDBSUFNFOUFTUEFNN
If backset is 2-3/4" (70 mm)
4JMBEJTUBODJBBMDFOUSPFT" (70 mm)
Si le ÏDBSUFNFOUFTUEF" (70 mm)
If backset is 2-1/2" (63,5 mm)
4JMBEJTUBODJBBMDFOUSPFT" (63,5 mm)
Si le ÏDBSUFNFOUFTUEFNN
If backset is 2-3/4" (70 mm)
4JMBEJTUBODJBBMDFOUSPFT" (70 mm)
Si le ÏDBSUFNFOUFTUEF" (70 mm)
THRU
1BTBOUF
®USBWFST
THRU
1BTBOUF
®USBWFST
IMPORTANT: Drill pilot holes rst.
*.1035"/5&1SJNFSPQFSGPSFPSJýDJPTQJMPUP
*.1035"/5ø1FSDFSEBCPSEMFTUSPVTEFHVJEBHF
IMPORTANT: Drill pilot holes rst.
*.1035"/5&1SJNFSPQFSGPSF
PSJýDJPTQJMPUP
*.1035"/5ø1FSDFSEBCPSEMFT
USPVTEFHVJEBHF
IMPORTANT: Door must be at
least 1-3/4" (44 mm) thick for
ush mounting.
*.1035"/5&-BQVFSUBEFCFUFOFS
VOBODIPEFBMNFOPT
NNQBSBFMNPOUBKFBMSBT
*.1035"/5-BQPSUFEPJUBWPJSVOF
ÏQBJTTFVSEBVNPJOT
NNQPVSVONPOUBHFFODBTUSÏ
Step 1 Use the mortise template to
prep the door edge.
Step 2 Use the trim template to
prep the face of the door.
Step 3 Install the mortise.
Step 4 Install the trim.
Paso 1 Utilice la plantilla de la mortaja
para preparar el borde la puerta.
Paso 2 Utilice la plantilla del contramarco
para preparar la cara de la puerta.
Paso 3 Instale la mortaja.
Paso 4 Instale el contramarco.
Étape 1 Utiliser le gabarit de la mortaise
pour préparer le bord de porte.
Étape 2 Utiliser le gabarit le plus petit pour
préparer la face de la porte.
Étape 3 Installer la mortaise.
Étape 4 Installer la plaque de finition.
Flush Mounting (for Standard Mounting template, see page 1)
Montaje al ras (para la plantilla de montaje estándar, vea la página 1)
Montage encastré (pour le gabarit pour montage standard, voir page 1)
BALDWINHARDWARE.COM
800.566.1986
PK.1029 Rev 01 PD006 Trim
© 2014 Baldwin Hardware Corporation2 / 2