Installation & Assembly

ManualsBrandsBARNSMITH ManualsBarn Interior DoorsGlass and Metal Barn Door with Installation Hardware Kit

Table Of Contents

Main Components

x2 Rail

Tools Required

Tape Measure

Pencil

Cordless Drill

Phillips Screwdriver

Wrench level

Speed Square

1/4"

Mortise Router Head

Required for

Floor-Mounted Door

Guide InstallationAllen

IMPORTANT: BEFORE YOU BEGIN

IF INSTALLING DIRECTLY INTO A NON-CONCRETE WALL, DO NOT ATTEMPT TO INSTALL THE RAIL SOLELY TO THE

DRYWALL OR ANY WALL SURFACE AS THIS MAY NOT SUPPORT THE WEIGHT OF THE RAIL AND MOUNTED DOOR.

THE RAIL MUST BE INSTALLED ONTO A PIECE OF SOLID WOOD BLOCKING ( ) USING MOUNTING PACKAGE NOT INCLUDED

SCREWS ( ). ENSURE THE SOLID WOOD BLOCKING IS SECURED INTO THE STRUCTURAL PACKAGE NOT INCLUDED

SURFACE. USE A STUD FINDER WHERE NECESSARY TO LOCATE STUDS AND SECURE SAFELY. TYPICAL SOLID WOOD

BLOCKING SHOULD BE 81 3/4" x 5 1/2" x 7/8".

x2 Roller Hanger

BARN DOOR HARDWARE KIT

INSTALLATION GUIDE

TSQ13BK-6FT+TKM04

M6x12mm

x4 (4.2mm x 25mm）

Floor Screws

x4 5/16"(8mm)

Floor Anchor

x2 Internal

Floor -Mounted

Door Guide

3/16" x 1"

x1 Right Stopper

x1 Left Stopper

x5 Washers

Allen Key

x5 (8mm x 90mm)

Wall Screw

x5 Wall Spacer

5/16" x 3 9/16"

x 2

x4 Hex Bolts

3/16" x 15/32"

NOTE, SEPARATE BOLTS ARE PROVIDED FOR 1 3/8" DOORS AND LONGER BOLTS PROVIDED FOR 1 3/4" DOORS. IF

INSTALLING WITH THE INTERNAL FLOOR-MOUNTED DOOR GUIDE, THE DOOR MUST BE MORTISED 1/4" WIDE X 3/4"

DEEP CENTRALLY.

x5 1/2" (10mm)

Anchor Floor

M4x6mm

5/32" x 1/4"

x2 Actuator

(4.2mm x 19mm)

3/16 " x 25/32"

Max

oad

40KGS

soft close

attachment

X6 Phillips screw

x2 Anti-jump Block

Summary of content (6 pages)

PAGE 1
BARN DOOR HARDWARE KIT TSQ13BK-6FT+TKM04 INSTALLATION GUIDE Main Components x4 Hex Bolts x2 Anti-jump Block x5 Wall Spacer x5 1/2" (10mm) Anchor Floor x5 (8mm x 90mm) 5/16" x 3 9/16" Wall Screw x5 Washers x2 Actuator x1 Left Stopper x 2 Allen Key M4x6mm 5/32" x 1/4" X6 Phillips screw (4.2mm x 19mm) 3/16 " x 25/32" x2 soft close attachment x4 (4.
PAGE 2
BARN DOOR HARDWARE KIT TSQ13BK-6FT+TKM04 INSTALLATION GUIDE Step 1. Door Preparation The door is divided into three parts.Please connect ①and② by ③ and fixed with 13/64'' x 9/16'' screws. 35 63/64'' (914mm) 84 1/64'' (2134mm) 1 3 2 13/64''x9/16'' M5x14(x12) Step 2.Soft Close Installation 1 Unscrew the screw with a wrench firstly.Change the soft closes to the correct direction, then tighten and install them on the rail.
PAGE 3
BARN DOOR HARDWARE KIT TSQ13BK-6FT+TKM04 INSTALLATION GUIDE Step 3. Door Preparation – Strap Installation Install the rollers on the reserved hole of the top of door by 3/16''x15/32'' screw. Step 4. CONCRETE Wall Preparation1 If installing with an opening for 80" standard door size, remove the top trim and cut the side trim horizontally along the height of the opening.
PAGE 4
BARN DOOR HARDWARE KIT TSQ13BK-6FT+TKM04 INSTALLATION GUIDE Step 6. CONCRETE Rail Installation When installing directly into concrete, align the spacers to holes,insert using the provided anchors and hex bolts (with washers).Ensure to un-screw to separate the hex bolt and anchor to install correctly, securing with a wrench. (X5) Step 7. Hanging the Door Place the assembled door onto the secured rail and tighten Step 8.
PAGE 5
BARN DOOR HARDWARE KIT TSQ13BK-6FT+TKM04 INSTALLATION GUIDE Step 9. Floor-Mounted Door Guide Installation Once the door is plumb, position the floor-mounted door guide inside the mortised door, line up close to the opening. Slide the door side-to-side to ensure functionality for final placement then mark holes with a pencil and pre-drill 5/16" holes. If drilling directly into a concrete floor, use the provided anchors. 1 30mm 3/16''(30mm) 5/16''(Ø8) Ø8 1 673 m/6 4'' m ( 37 .5 m m ) Step 10.
PAGE 6
BARN DOOR HARDWARE KIT TSQ13BK-6FT+TKM04 INSTALLATION GUIDE Step 11.Install right soft close attachment 1.Push the door to the right, push it to the required position. place the actuator connector in the middle of the actuator claw. 2. Insert the washers and tighten it with a wrench. 3. Push the door to the left and install the actuator on the connector. 4. Move the actuator claw to the left, adjust the actuator to a limited position. adjust the height of the soft close, and make sure it works.