INSTALLATION INSTRUCTIONS 1-800 UNIT No. 4400 & 4500 BATH ENCLOSURE NE INSTA ED LLAT HELP ION ? -45-B Call ASCO (452Mon 2726 8:00 day - Frida ) A.M. y Easte 4:30 P.M .
MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized aluminum. To assure a long lasting finish on the enclosure, wipe it down with a towel after each use. Never use a scouring agent to clean the aluminum. For occasional, more concentrated cleaning efforts, we find that Lysol Bathroom Cleaner works extremely well. Be sure that any over spray falling on the aluminum frame is rinsed thoroughly and dried.
4400/4500 PARTS LIST A. B. C. D. E. F. G. H. I. J. 1 2 6 6 4 1 2 4 4 8 K. L. M. N. S. T. U. V. X. W.
1 Measure the wall-to-wall opening at the center of the tub rim. Cut the tub track [A] 1/16” short of this dimension. An inexpensive miter box available at your local hardware store will help you get clean square cuts. WALL JAMB Position the tub track in the center of the tub rim with the tall leg to the exterior. It may be necessary to file a radius on the ends of the tub track and wall jambs to match the corners of the tub. TUB TRACK Press both wall jambs [B] into position over the tub track.
4 Replace one wall jamb [B] and attach to the wall with a #8 x 1 1/2” truss head screw [D] inserted through the center hole. Slip a nylon spacer [E] over a #8 x 1 1/2” truss head screw and install in the top hole of the wall jamb. Repeat for the bottom jamb. Check jamb for plumb and tighten screws. WALL JAMB NYLON SPACER NOTE: Do not over-tighten the jamb screws. 1 1/2” TRUSS HEAD SCREW 5 This bath enclosure is equipped with safety teelock wall jambs.
7 Slide one of the clear plastic discs [J], then a glass hole sleeve [K] onto the back plate [I]. Push the assembly through the hole in the glass panel, so that the glass hole sleeve is flush with the other side of the panel. Slide the other clear plastic disc onto the protruding end of the back plate, and then slide on the front plate [L]. Repeat this for the second hole on the panel. While holding the towel bar [N] in place, and screw the back plates into the towel bar.
10 Locate the nylon bottom guide [S] in the middle of the tub track [A] with the glass panels in the position shown. With a 7/64” bit, drill two holes into the V-groove through the mounting holes in the guide. Install the bottom guide with two #6 x 3/8” pan head screws [T] thru the drilled holes as shown. GLAZED PANELS CENTER GUIDE TUB TRACK (2) #6 X 3/8 “ PAN HEAD SCREW INTERIOR 11 Slide the stainless steel bumper inserts [U] into the four soft vinyl jamb bumpers [V].
13 Peel the backing from the Basco decal [W] and place it at the end of the header [F] on the interior face.
CURVED TOWEL BAR SUPPLEMENT Slide one of the clear plastic discs [J], then a glass hole sleeve [K] onto the back plate [I]. Push the assembly through the hole in the glass panel, so that the glass hole sleeve is flush with the other side of the panel. Slide the other clear plastic disc onto the protruding end of the back plate, and then slide on the front plate [L]. Repeat this for the second hole on the panel. While holding the towel bar [N] in place, and screw the back plates into the towel bar. I. J. K.
